EF Logo

Volvo/Mack · MID 128 engine ECU - module, data link and power

Volvo/Mack J1939 data link 2 (aftertreatment) fault codes

The second J1939 data link connects the engine ECU to the aftertreatment control unit and NOx sensors.

FaultCheckMID 128PSID 229FMI 9Volvo/Mack · SAE J1939 data link 2
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PSID 229 FMI 2 and MID 128 PSID 229 FMI 9 are all about the j1939 data link 2 (aftertreatment). None needs an immediate stop. Start with this check: check the link wiring and connectors for chafing, corrosion and pins that have been pushed back.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Check the link wiring and connectors for chafing, corrosion and pins that have been pushed back

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PSID 229 FMI 2SAE J1939 data link 2 circuit shorted or open

    The engine ECM sees the J1939 data link 2 shorted to positive or ground, or open.· Erratic or implausible
    Check soon

    Causes

    • CAN 2 wire shorted to positive
    • CAN 2 wire shorted to ground
    • Open circuit on the CAN 2 harness
    • Damaged data link connector

    Checks

    1. 1Check resistance between the two CAN 2 wires at the engine ECM connector
    2. 2Check each CAN wire for a short to ground and to battery
    3. 3Inspect connectors for corrosion and bent pins
    4. 4Disconnect the aftertreatment module to see if the bus recovers
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Volvo/Mack MID 128 PSID 229 FMI 9SAE J1939 data link 2 - Lost communication with aftertreatment module

    The engine ECM no longer receives messages from the aftertreatment control module on the second J1939 data link (SPN 1231).· Lost message
    Check soon

    Causes

    • Damaged CAN 2 harness or connector between the engine ECM and the aftertreatment module
    • DEF pump or aftertreatment DEF module pulling down the data link
    • Aftertreatment control module failure
    • Low supply voltage to the aftertreatment module

    Checks

    1. 1First check if the fault is active; Mack says an inactive code counted in multiples of three on 2010-2013 MP7/MP8 may only need an engine software update
    2. 2Check battery voltage and the aftertreatment module power and ground
    3. 3Check the engine-side data link connectors for water and corrosion
    4. 4Measure the CAN 2 pair resistance at the engine ECM connector
    5. 5Isolate the DEF pump connector to see if the bus recovers
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Check the link wiring and connectors for chafing, corrosion and pins that have been pushed back
  2. 2Measure the resistance between the two data link wires with the power off and compare it with the expected value
  3. 3Check the supply and ground of the aftertreatment unit
  4. 4Check which other modules on the link are still answering to separate a wiring fault from one dead unit

Causes

  • Damaged wiring or a poor connector
  • Missing termination resistor
  • Aftertreatment unit not powered

When to stop

You'll notice: Aftertreatment warnings appear and regeneration or DEF dosing may be limited.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.