EF Logo

Volvo/Mack · MID 144 vehicle ECU

Volvo/Mack Accelerator pedal position fault codes

The accelerator pedal sensor tells the vehicle ECU how far the driver presses the pedal. It uses a main signal and idle validation switches.

FaultCheckMID 144PID 91FMI 3Volvo/Mack · Accelerator pedal position
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 144 PID 91 FMI 3 to MID 144 PID 91 FMI 6 are all about the accelerator pedal position. The most common failure type is shorted low (2 of 4); none needs an immediate stop. Start with this check: inspect the pedal connector and harness for corrosion, chafing and pins that are loose or pushed back.

How urgent are they?

None of the 4 codes here means stop now; all 4 can wait until the shift ends, but find the cause before the next one.

  • Check soon4

What should I check first?

Inspect the pedal connector and harness for corrosion, chafing and pins that are loose or pushed back

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 144 PID 91 FMI 3Accelerator pedal position signal high

    The pedal position sensor signal is above about 4.3 V, which the VECU treats as an abnormally high voltage or a short to a higher voltage.· Shorted high
    Check soon

    Causes

    • Accelerator pedal position harness shorted high
    • Faulty accelerator pedal position sensor
    • Short to battery voltage in the pedal connector

    Checks

    1. 1Read the pedal percentage with the pedal released; it should sit at zero
    2. 2Unplug the pedal sensor and measure the sensor supply at the harness plug
    3. 3Check the pedal signal wire for a short to a supply wire with the key off
    4. 4Check the pedal connector for bent pins and corrosion
    5. 5Replace the pedal assembly after the harness passes
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 144 PID 91 FMI 4Accelerator pedal position signal low

    The pedal position sensor signal is below about 0.4 V, which the VECU treats as an abnormally low voltage or a short to a lower voltage.· Shorted low
    Check soon

    Causes

    • Accelerator pedal position harness shorted low
    • Faulty accelerator pedal position sensor
    • Lost sensor signal wire

    Checks

    1. 1Read the pedal value in the scan tool as you press the pedal; a flat reading near zero confirms the fault
    2. 2Unplug the sensor and check the supply and ground pins at the harness
    3. 3Test the signal wire for a short to ground with the key off
    4. 4Check for an open signal wire by continuity to the VECU
    5. 5Replace the pedal assembly if the harness tests good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 144 PID 91 FMI 5Accelerator pedal position low compared with idle validation switches

    The pedal input is too low compared with the idle validation switches IVS1 and IVS2.· Open circuit
    Check soon

    Causes

    • Faulty accelerator pedal position sensor
    • Open sensor wiring
    • Idle validation switch disagreement

    Checks

    1. 1Compare the pedal reading and the idle validation switch state while pressing the pedal slowly
    2. 2Check the pedal connector and wiring for opens
    3. 3Check the pedal sensor supply voltage at the plug
    4. 4Replace the pedal assembly if the readings disagree on a good harness
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 144 PID 91 FMI 6Accelerator pedal position high compared with idle validation switches / loss of sensor ground

    The pedal input is too low compared with IVS1 and IVS2 in the opposite direction, which the VECU reads as high current or a short to ground.· Shorted low
    Check soon

    Causes

    • Faulty accelerator pedal position sensor
    • Loss of the pedal sensor ground
    • Short to ground in the signal wire

    Checks

    1. 1Measure the pedal sensor ground at the harness plug with the key on
    2. 2Check the signal wire for a short to ground with the key off
    3. 3Compare pedal and idle validation switch states in the scan tool
    4. 4Replace the pedal assembly if the ground and signal are good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Inspect the pedal connector and harness for corrosion, chafing and pins that are loose or pushed back
  2. 2Check the sensor supply and ground at the pedal plug with the key on and compare with the service data
  3. 3Read the pedal position on the scan tool
  4. 4Compare idle validation with pedal released

Causes

  • Pedal sensor failed
  • Damaged wiring or connector
  • Sensor supply fault

Most common here: shorted low (2 of 4)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: The engine does not respond to the pedal correctly, may idle only, and a check lamp comes on.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.