Thermo King · Engine speed and starting (SR-2/SR-3/SR-4)
Thermo King Fault Code 07
Check engine RPM sensor
What does Thermo King code 07 mean?
The controller is not getting a valid speed signal from the engine RPM sensor, usually a magnetic pickup at the flywheel, so it cannot tell whether the engine is running or at what speed. Urgency: stop now - shut down and fix before working on. Check first: check the pickup is seated and the tip is clean and free of metal swarf.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check the pickup is seated and the tip is clean and free of metal swarf
Then 4 more checksWhere this code shows
Press the alarm key or open the Alarms menu on the controller display to list active alarms.
Checks
0 of 5 done
Causes
- Magnetic pickup gap wrong or sensor loose in the bell housing
- Pickup coil open or wiring broken
- Metal debris on the pickup tip
- Connector pins corroded on the engine harness
How it failed
You'll notice: Engine may crank and start but the controller shuts it down, or it cranks too long; alarm 07 shown and engine speed control is lost.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine starting, glow plugs and engine speed
- 07Check engine RPM sensorOtherStop now
- 15Check glow plugs or intake air heaterOtherCheck soon
- 16Manual start not completedOtherInformation
- 17Engine failed to crankOtherStop now
- 20Engine failed to startOtherStop now
- 33Check engine RPMOtherCheck soon
- 40Check high speed circuitOtherCheck soon
- 42Unit forced to low speedOtherCheck soon
- 43Unit forced to low speed modulationOtherCheck soon
Show the other 14 codesHide the other codes
- 55Check engine speedsOtherCheck soon
- 511Engine wait to start time delay expiredOtherInformation
- 600Check crankshaft speed sensorOtherStop now
- 601Check camshaft speed sensorOtherCheck soon
- 611Check glow plug circuitOtherCheck soon
- 620No RPM detected during start attemptOtherStop now
- 642ECU forced low speedOtherInformation
- 800Crankshaft position sensor errorOtherInformation
- 801Camshaft position sensor errorOtherInformation
- 811Glow plug circuit errorOtherInformation
- 839Engine speed errorOtherInformation
- 842Engine running in safe mode - low speedOtherInformation
- 844Engine failed to crank (engine ECU)OtherStop now
- 845Starter relay errorOtherInformation
Other Thermo King codes: Engine speed and starting (SR-2/SR-3/SR-4)
Source
Thermo King Alarm Codes - North America (thermoking.com alarm code list)
This source lists 07 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Thermo King SR-2, SR-3, SR-4 truck and trailer units and related Thermo King controllers (the families the source lists).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
