EF Logo

Kubota · Engine ECU - SPN / FMI codes

Kubota Intake air, boost, airflow and throttle fault codes

This page covers the air path: boost pressure, air pressure sensors, mass air flow, the intake throttle, intake air performance and the barometric (ambient air) pressure sensor. The boost or intake manifold sensor and the atmospheric sensor give the engine ECU the air pressure it needs to calculate fuelling and exhaust gas recirculation.

More about these parts

The engine ECU compares the air that reaches the engine with what it expects for the load. The mass air flow sensor measures the air going into the engine and the intake throttle valve closes a little during regeneration to raise exhaust temperature. The boost pressure sensor in the intake manifold tells the engine ECU how much the turbocharger is pushing. The mass air flow sensor measures how much air enters the engine. The intake throttle valve, which is partly closed during regeneration, is moved by a motor with a lift sensor. The barometric sensor tells the engine ECU the air pressure around the machine so fuel and smoke limits can be corrected for altitude.

FaultCheckSPN102-FMI3Kubota · Boost pressure sensor
Code shows hereFAULTSPN102-FMI3

Where this code shows

Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.

What do these codes mean?

Kubota codes SPN102-FMI3 to SPN523582-FMI4 are all about the intake air, boost, airflow and throttle. The most common failure type is shorted high (4 of 17); none needs an immediate stop. Start with this check: read the pressure in Diagmaster with the key on and the engine off; it should match the local air pressure.

How urgent are they?

None of the 17 codes here means stop now; all 17 can wait until the shift ends, but find the cause before the next one.

  • Check soon17

What should I check first?

Read the pressure in Diagmaster with the key on and the engine off; it should match the local air pressure

Shared checks

17 of 17

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Kubota SPN102-FMI3Boost pressure sensor - Short to battery

    SPN 102 FMI 3 means the boost pressure sensor reads above range.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to supply
    • Failed boost sensor
    • Connector contamination with oil

    Checks

    1. 1Read the boost at key on; an impossibly high value confirms the fault
    2. 2Unplug the sensor and check whether the reading changes
    3. 3Check the boost sensor signal wire for a short to a supply line
    4. 4Inspect the boost sensor connector for oil mist and water
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN102-FMI4Boost pressure sensor - Open circuit or short to ground

    SPN 102 FMI 4 means the boost pressure sensor reads below range.· Shorted low
    Check soon

    Causes

    • Open boost sensor signal wire
    • Signal wire shorted to ground
    • Failed boost sensor

    Checks

    1. 1Read the boost value in Diagmaster at key on; it should match atmospheric pressure
    2. 2Back-probe supply, ground and signal at the sensor connector
    3. 3Check the signal wire for an open or short to ground
    4. 4Inspect the connector and sensor port for soot
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN108-FMI3Barometric pressure sensor - Short to battery

    SPN 108 FMI 3 means the barometric pressure sensor circuit is shorted to battery positive.· Shorted high
    Check soon

    Causes

    • Wire chafed and touching a live supply wire
    • Failed barometric pressure sensor
    • Water inside the barometric pressure sensor connector

    Checks

    1. 1Unplug the barometric pressure sensor and check with the key on that the wire carries no voltage
    2. 2Follow the harness and look for rubbed insulation next to power wires
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN108-FMI4Barometric pressure sensor - Short to ground

    SPN 108 FMI 4 means the barometric pressure sensor circuit is shorted to ground.· Shorted low
    Check soon

    Causes

    • Wire chafed through and touching the engine or frame
    • Failed barometric pressure sensor
    • Water inside the barometric pressure sensor connector

    Checks

    1. 1Unplug the barometric pressure sensor and measure the wire to ground with the key off; it should read open
    2. 2Follow the harness and look for chafed insulation at brackets and sleeves
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN132-FMI1Intake air volume low

    SPN 132 FMI 1 means the engine takes in less air than the ECU expects for the fuel it is injecting.· Real condition
    Check soon

    Causes

    • Blocked air cleaner or collapsed intake hose
    • Air leak between the air flow sensor and the intake
    • Dirty air flow sensor element

    Checks

    1. 1Check the air cleaner and its restriction indicator and the intake hose between filter and turbo
    2. 2Compare the air flow value in Diagmaster at idle with the reading at high idle
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN132-FMI3MAF sensor - Short to battery

    SPN 132 FMI 3 means the mass air flow sensor signal is above range, typically a short to a supply line or a failed sensor circuit.· Shorted high
    Check soon

    Causes

    • MAF sensor electronics failed
    • Signal short to supply
    • Connector bridged by water

    Checks

    1. 1Read the intake air flow at key on; a high reading with no airflow confirms the fault
    2. 2Check the MAF sensor wiring for a short to a supply line
    3. 3Inspect the MAF sensor connector for moisture and bridged terminals
    4. 4Look at the harness routing near the intake for chafing
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN132-FMI4MAF sensor - Open circuit or ground short

    SPN 132 FMI 4 means the mass air flow sensor signal is below range, typically an open circuit or short to ground.· Shorted low
    Check soon

    Causes

    • MAF sensor failed
    • Open signal wire
    • Signal short to ground

    Checks

    1. 1Read the intake air flow in Diagmaster at idle
    2. 2Check the signal wire for an open or a short to ground
    3. 3Inspect the connector for corrosion and bent pins
    4. 4Check the air path for obstruction before the sensor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN132-FMI15Boost pressure is low

    SPN 132 FMI 15 is a mild warning that boost pressure stays lower than the ECU expects for the load.· Real condition
    Check soon

    Causes

    • Boost leak at a hose clamp or charge air pipe
    • Turbocharger worn or sticking
    • Blocked air cleaner

    Checks

    1. 1Inspect and tighten the hoses and clamps between the turbo and the intake manifold
    2. 2Read the boost pressure under load in Diagmaster and compare it with the load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota E:9107Intake air pressure sensor system error

    The boost or intake manifold pressure sensor signal is out of range.· Other
    Check soon

    Causes

    • Boost pressure sensor failed
    • Plugged sensor port or hose
    • Wire open or short

    Checks

    1. 1Compare the boost reading at key on with atmospheric pressure
    2. 2Check the sensor port and hose for soot or oil blockage
    3. 3Back-probe the 5 V supply, ground and signal at the sensor
    4. 4Inspect the intake system for leaks and loose clamps
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9112Atmospheric pressure sensor system error

    The barometric pressure sensor reads outside its range.· Lost message
    Check soon

    Causes

    • Barometric sensor failed
    • Wire fault
    • ECU internal sensor fault

    Checks

    1. 1Compare the pressure reading at key on with the local atmospheric value
    2. 2Inspect the sensor wiring and connector for damage
    3. 3Check the sensor supply and ground at the connector
    4. 4Replace the sensor, or the ECU if the sensor is built into it
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Kubota E:9200Mass air flow sensor system error

    The mass air flow (MAF) sensor on the intake is giving an abnormal signal.· Lost message
    Check soon

    Causes

    • MAF sensor element dirty or failed
    • Air leak between the sensor and the turbo or manifold
    • Open or shorted wire at the MAF connector

    Checks

    1. 1Inspect the air cleaner and intake hose for restriction, cracks and loose clamps
    2. 2Read intake air quantity in Diagmaster at idle and compare it with a known good machine
    3. 3Check the MAF connector and wires for water, pushed-back pins and chafing
    4. 4Back-probe the sensor supply and signal for a stable reading while the engine runs
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Kubota E:9203Intake air throttle error

    The intake throttle valve that helps raise exhaust temperature for regeneration is not moving as commanded.· Other
    Check soon

    Causes

    • Throttle valve sticking with soot
    • Throttle actuator motor failed
    • Lift sensor on the valve reading out of range

    Checks

    1. 1Look at the throttle valve for soot build-up and free movement
    2. 2Command the throttle in Diagmaster and watch the commanded versus actual position
    3. 3Check the throttle connector and wires for damage and water
    4. 4Measure the lift sensor signal; it should move smoothly between about 0.5 and 4.5 V
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9305Engine air intake system error (poor air intake)

    The engine is not getting enough intake air for the fuel it is injecting.· Other
    Check soon

    Causes

    • Air cleaner clogged
    • Intake hose collapsed
    • Air leak

    Checks

    1. 1Inspect the air cleaner element and replace it if clogged
    2. 2Check the intake hoses for collapse and cracks
    3. 3Read the MAF airflow value in Diagmaster at idle and compare with a good machine
    4. 4Check the intake clamps and joints for leaks that let dirty air in
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9306Engine air intake system error (boost pressure too low)

    The measured boost pressure is lower than the ECU expects for the load, so the engine cannot make its full power.· Real condition
    Check soon

    Causes

    • Boost leak
    • Turbo worn
    • Boost sensor fault

    Checks

    1. 1Check the turbo outlet hoses and clamps for boost leaks, oil mist or splits
    2. 2Read the boost pressure in Diagmaster under load
    3. 3Check the turbo shaft for play and oil leaking from the compressor housing
    4. 4Check the boost sensor signal for a stuck value
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN523580-FMI2Intake throttle feedback error

    SPN 523580 FMI 2 means the intake throttle valve does not reach the commanded position.· Erratic or implausible
    Check soon

    Causes

    • Valve stuck with soot
    • Motor failed
    • Feedback wire fault

    Checks

    1. 1Inspect the valve for soot
    2. 2Command the valve in Diagmaster
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523582-FMI3Intake throttle lift sensor high

    SPN 523582 FMI 3 means the lift sensor of the intake throttle reads too high.· Shorted high
    Check soon

    Causes

    • Sensor wire shorted to battery
    • Sensor failed
    • Corroded connector

    Checks

    1. 1Check the sensor connector and wires
    2. 2Read the position in Diagmaster
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN523582-FMI4Intake throttle lift sensor low

    SPN 523582 FMI 4 means the lift sensor of the intake throttle reads too low.· Shorted low
    Check soon

    Causes

    • Sensor wire open or shorted to ground
    • Sensor failed
    • Corroded connector

    Checks

    1. 1Check the sensor connector and wires
    2. 2Read the position in Diagmaster
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Read the pressure in Diagmaster with the key on and the engine off; it should match the local air pressure
  2. 2Check the air cleaner and its restriction indicator
  3. 3Inspect the air cleaner and intake hose for restriction and leaks
  4. 4Read the boost pressure in Diagmaster while the engine is under load
  5. 5Check the air cleaner and the intake hose between filter and turbo for leaks
  6. 6Inspect the throttle valve for soot and free movement
  7. 7Compare the barometric reading in Diagmaster with the known air pressure for your site altitude

Causes

  • Sensor supply or ground wire damaged
  • Blocked air cleaner or intake hose
  • Dirty air flow sensor element or wiring fault
  • Boost sensor wiring or connector fault

Most common here: shorted high (4 of 17)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: Loss of power, black smoke or poor power at altitude, with the E:91xx code.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.