EF Logo

Kubota · Engine ECU - SPN / FMI codes

Kubota Exhaust gas temperature sensors and high exhaust temperature fault codes

This page covers exhaust temperature: the T0, T1 and T2 sensor circuits, the E:92xx sensor errors, and the high and out-of-range exhaust temperature codes. Three exhaust temperature sensors sit before the oxidation catalyst, between the catalyst and the particulate filter, and at the filter outlet.

More about these parts

The exhaust gas temperature sensors T0, T1 and T2 sit around the oxidation catalyst and the particulate filter in the engine's SPN code table. The engine ECU expects the exhaust temperature at the oxidation catalyst and the particulate filter to follow a pattern during regeneration. These codes report exhaust gas temperatures above the allowed limit at the oxidation catalyst or the filter outlet, or a failure of all temperature sensors.

FaultStopSPN3242-FMI0Kubota · Exhaust gas temperature sensor T1
Code shows hereFAULTSPN3242-FMI0

Where this code shows

Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.

What do these codes mean?

Kubota codes SPN3242-FMI0 to SPN523601-FMI0 are all about the exhaust gas temperature sensors and high exhaust temperature. The most common failure type is real condition (9 of 19); 6 need an immediate stop. Start with this check: compare the three exhaust temperature readings in Diagmaster with the engine cold; they should be close.

How urgent are they?

6 of 19 codes here mean stop now; the other 13 can wait until the shift ends, but find the cause before the next one.

  • Stop now6
  • Check soon13

What should I check first?

Compare the three exhaust temperature readings in Diagmaster with the engine cold; they should be close

Shared checks

19 of 19

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Kubota SPN3242-FMI0Exhaust gas temperature sensor T1 - Emergency high

    SPN 3242 FMI 0 means exhaust sensor T1 reached the emergency high temperature.· Real condition
    Stop now

    Causes

    • Unburned fuel burning in the catalyst
    • Clogged particulate filter
    • Sensor T1 reading wrongly

    Checks

    1. 1Check for injector or fuel codes first
    2. 2Compare sensor T1 with the other two exhaust sensors in Diagmaster
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN3242-FMI3Exhaust gas temperature sensor T1 - Open circuit or short to battery

    SPN 3242 FMI 3 means the exhaust gas temperature sensor T1 signal reads above its range, which points to an open circuit or a short to battery positive.· Shorted high
    Check soon

    Causes

    • Open signal or ground wire letting the signal float high
    • Signal wire shorted to battery positive
    • Failed exhaust gas temperature sensor T1 or corroded connector

    Checks

    1. 1Unplug the exhaust gas temperature sensor T1 and check the signal and ground wires for continuity back to the ECU
    2. 2With the key on, measure the signal wire for voltage above the 5 V supply
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN3242-FMI4Exhaust gas temperature sensor T1 - Short to ground

    SPN 3242 FMI 4 means the exhaust gas temperature sensor T1 circuit is shorted to ground.· Shorted low
    Check soon

    Causes

    • Wire chafed through and touching the engine or frame
    • Failed exhaust gas temperature sensor T1
    • Water inside the exhaust gas temperature sensor T1 connector

    Checks

    1. 1Unplug the exhaust gas temperature sensor T1 and measure the wire to ground with the key off; it should read open
    2. 2Follow the harness and look for chafed insulation at brackets and sleeves
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN3246-FMI0Exhaust gas temperature sensor T2 - Emergency high

    SPN 3246 FMI 0 means exhaust sensor T2 reached the emergency high temperature.· Real condition
    Stop now

    Causes

    • Unburned fuel burning in the catalyst
    • Clogged particulate filter
    • Sensor T2 reading wrongly

    Checks

    1. 1Check for injector or fuel codes first
    2. 2Compare sensor T2 with the other two exhaust sensors in Diagmaster
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN3246-FMI3Exhaust gas temperature sensor T2 - Open circuit or short to battery

    Same open-circuit or short-to-battery fault as SPN 3242, on exhaust gas temperature sensor T2.· Shorted high
    Check soon

    Causes

    • Open signal or ground wire at sensor T2
    • Sensor T2 connector corroded

    Checks

    1. 1Check the sensor T2 signal and ground wires for continuity back to the ECU.
    2. 2Key on, look for voltage above 5 V on the sensor T2 signal wire.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN3246-FMI4Exhaust gas temperature sensor T2 - Short to ground

    Same short-to-ground fault as SPN 3242, on exhaust gas temperature sensor T2.· Shorted low
    Check soon

    Causes

    • Sensor T2 wire rubbed through to the frame
    • Failed sensor T2

    Checks

    1. 1Unplug sensor T2 and check its wire to ground reads open with the key off.
    2. 2Follow the T2 harness through its brackets and sleeve for rubbed insulation.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN3252-FMI0Oxidation catalyst heated by unburned fuel

    SPN 3252 FMI 0 means the oxidation catalyst is getting hot because unburned fuel reaches it.· Real condition
    Stop now

    Causes

    • Leaking or stuck-open injector
    • Rail pressure too high
    • Poor combustion

    Checks

    1. 1Check the injectors and read the other fuel codes
    2. 2Check the oil level for fuel dilution
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN4765-FMI0Exhaust gas temperature sensor T0 - Emergency high

    SPN 4765 FMI 0 means exhaust sensor T0 reached the emergency high temperature.· Real condition
    Stop now

    Causes

    • Unburned fuel burning in the catalyst
    • Clogged particulate filter
    • Sensor T0 reading wrongly

    Checks

    1. 1Check for injector or fuel codes first
    2. 2Compare sensor T0 with the other two exhaust sensors in Diagmaster
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN4765-FMI3Exhaust gas temperature sensor T0 - Open circuit or short to battery

    Same open-circuit or short-to-battery fault as SPN 3242, on exhaust gas temperature sensor T0.· Shorted high
    Check soon

    Causes

    • Open signal or ground wire at sensor T0
    • Sensor T0 connector corroded

    Checks

    1. 1Check the sensor T0 signal and ground wires for continuity back to the ECU.
    2. 2Key on, look for voltage above 5 V on the sensor T0 signal wire.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN4765-FMI4Exhaust gas temperature sensor T0 - Short to ground

    Same short-to-ground fault as SPN 3242, on exhaust gas temperature sensor T0.· Shorted low
    Check soon

    Causes

    • Sensor T0 wire rubbed through to the frame
    • Failed sensor T0

    Checks

    1. 1Unplug sensor T0 and check its wire to ground reads open with the key off.
    2. 2Follow the T0 harness through its brackets and sleeve for rubbed insulation.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota E:9205Exhaust temperature sensor error (DOC inlet)

    The exhaust temperature sensor at the diesel oxidation catalyst inlet reports an abnormal value.· Other
    Check soon

    Causes

    • DOC inlet temperature sensor failed
    • Wiring damaged by exhaust heat
    • Connector corroded

    Checks

    1. 1Read the DOC inlet temperature cold; it should be close to ambient
    2. 2Inspect the sensor wiring for heat damage and chafing
    3. 3Measure the sensor resistance against the manual curve
    4. 4Check the sensor connector near the DOC for soot, heat damage and water
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9206Exhaust temperature sensor error (DOC outlet)

    The sensor between the DOC and the DPF reports an abnormal value.· Other
    Check soon

    Causes

    • DOC outlet temperature sensor failed
    • Heat damaged harness near the catalyst
    • Connector fault at the mid-exhaust plug

    Checks

    1. 1Compare this sensor with the DOC inlet reading when the engine is cold
    2. 2Inspect the harness where it passes the exhaust pipe
    3. 3Measure the sensor resistance and compare it with the manual curve
    4. 4Check the exhaust pipe joints for leaks that cool the sensor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9207Exhaust temperature sensor error (DPF outlet)

    The sensor on the DPF outlet reports an abnormal value.· Real condition
    Check soon

    Causes

    • DPF outlet temperature sensor failed
    • Heat damaged harness at the tailpipe end
    • Corroded connector

    Checks

    1. 1Check this sensor cold against the other exhaust sensors; all should be near ambient
    2. 2Inspect the harness at the outlet side for heat damage
    3. 3Measure sensor resistance against the manual curve
    4. 4Clean the tailpipe-side connector of soot and check the terminals for corrosion
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota E:9208All exhaust temperature sensors failed at once

    All exhaust temperature sensors fail together, which points to a shared supply, ground or ECU problem rather than three separate sensors.· Real condition
    Check soon

    Causes

    • Shared 5 V supply or ground problem
    • Harness damaged between the exhaust and the ECU
    • Water in the exhaust sensor connector

    Checks

    1. 1Check the ECU supply and ground pins for the exhaust sensor group
    2. 2Inspect the harness for a pinched or burnt bundle
    3. 3Measure each sensor separately for open or short
    4. 4Check connectors for water ingress and corrosion
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota E:9307Exhaust temperature (DOC inlet) out of specification

    The DOC inlet temperature is outside the range the ECU expects during regeneration, so the cycle is stopped or fails.· Other
    Check soon

    Causes

    • Sensor fault at the DOC inlet
    • Fuel dosing fault
    • Exhaust leak ahead of the DOC

    Checks

    1. 1Read the DOC inlet sensor during regeneration in Diagmaster
    2. 2Check the fuel dosing and injectors for faults
    3. 3Check the exhaust manifold and turbo outlet joints for leaks before the DOC
    4. 4Inspect the DOC inlet face for soot, cracks or melted material
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9308Exhaust temperature (DOC outlet) out of specification

    The temperature leaving the DOC is outside what the ECU expects, which can mean the catalyst is not reacting properly.· Lost message
    Check soon

    Causes

    • Sensor fault at the DOC outlet
    • Poor DOC activity from age or contamination
    • Exhaust leak between DOC and DPF

    Checks

    1. 1Read the DOC outlet sensor during regeneration against the inlet
    2. 2Look at the DOC condition for soot, oil fouling or a washed-out coating
    3. 3Check the joints between the DOC and the DPF for exhaust leaks
    4. 4Check fuel dosing and the injectors for faults that starve the DOC of heat
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Kubota E:9309Exhaust temperature (DPF outlet) out of specification

    The DPF outlet temperature is outside the range the ECU expects, which may mean the filter is overheating or not regenerating.· Real condition
    Check soon

    Causes

    • Sensor fault at the DPF outlet
    • DPF overheating from heavy soot
    • Exhaust leak at the outlet

    Checks

    1. 1Read the DPF outlet temperature during regeneration
    2. 2Check the DPF canister for heat discolouration and cracking from overheating
    3. 3Check the DPF outlet pipe and muffler joints for exhaust leaks
    4. 4Check the soot load and ash counters for the DPF in Diagmaster
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN523599-FMI0All exhaust gas temperature sensors failed

    SPN 523599 FMI 0 means all exhaust sensors report failure at once.· Real condition
    Stop now

    Causes

    • Shared sensor supply or ground fault
    • Harness burnt near the filter
    • ECU input fault

    Checks

    1. 1Inspect the harness at the DPF for heat damage
    2. 2Measure the shared supply and ground at a sensor connector
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Kubota SPN523601-FMI0High exhaust temperature after emergency high temperature code

    SPN 523601 FMI 0 means the exhaust stayed too hot after the emergency high temperature code was raised.· Real condition
    Stop now

    Causes

    • Cause of the first overheat not fixed
    • Clogged filter
    • Injector leak

    Checks

    1. 1Read all stored exhaust codes and clear them after repair
    2. 2Check the filter condition with the differential pressure reading
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Compare the three exhaust temperature readings in Diagmaster with the engine cold; they should be close
  2. 2Compare T0, T1 and T2 in Diagmaster with a cold engine; all three should read alike
  3. 3Compare the three exhaust temperatures in Diagmaster during a regeneration
  4. 4Check for injector or fuel system codes first
  5. 5Inspect the harness and sleeve near the DPF for burnt or worn insulation
  6. 6Inspect the harness at the bottom of the grey sleeve before the DPF muffler
  7. 7Inspect the exhaust for leaks and the sensors for damage

Causes

  • Sensor wire chafed or burnt near the exhaust
  • Sensor wire burnt or rubbed through at the DPF sleeve
  • Exhaust temperature sensor reading wrongly
  • Unburned fuel reaching the catalyst from an injector fault

Most common here: real condition (9 of 19)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: DPF lamp and the E:92xx code; regeneration may not run and the engine can be limited.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.