EF Logo

Kubota · Engine ECU - SPN / FMI codes

Kubota ECU internal faults, CAN bus and accelerator position fault codes

This page covers the engine ECU itself and its inputs from the machine: ECU internal faults, the ECU link, the engine CAN bus and frames, the accelerator position sensors and the catch-all E:9400 other engine failures. The engine ECU runs self-checks on its memory and processors.

More about these parts

The engine ECU is a separate controller that must exchange data with the machine controller over the CAN bus. The engine ECU receives frames from the machine controller for parking switch, vehicle speed, regeneration switch, neutral switch and speed requests. The accelerator has two position sensors that the engine ECU compares to detect faults.

FaultCheckSPN29-FMI3Kubota · Accelerator position sensor 2
Code shows hereFAULTSPN29-FMI3

Where this code shows

Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.

What do these codes mean?

Kubota codes SPN29-FMI3 to SPN523700-FMI13 are all about the eCU internal faults, CAN bus and accelerator position. Most are erratic or implausible faults; 6 need an immediate stop. Start with this check: check battery voltage and the ECU supply fuses.

How urgent are they?

6 of 21 codes here mean stop now; the other 15 can wait until the shift ends, but find the cause before the next one.

  • Stop now6
  • Check soon15

What should I check first?

Check battery voltage and the ECU supply fuses

Shared checks

21 of 21

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Kubota SPN29-FMI3Accelerator position sensor 2 - Short to battery

    SPN 29 FMI 3 means the accelerator position sensor 2 signal reads above its range, which points to a short to battery positive.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to battery positive or to a sensor supply
    • Failed accelerator position sensor 2
    • Chafed harness touching a live wire

    Checks

    1. 1With the accelerator position sensor 2 unplugged and the key on, measure the signal wire; any voltage above 5 V points to a harness short
    2. 2Check the harness near the engine brackets for chafing against live wires
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN29-FMI4Accelerator position sensor 2 - Ground short or open circuit

    SPN 29 FMI 4 means the accelerator position sensor 2 signal reads below its range, which points to an open circuit or a short to ground.· Shorted low
    Check soon

    Causes

    • Open circuit in the accelerator position sensor 2 signal or ground wire
    • Signal wire shorted to ground
    • Failed accelerator position sensor 2 or corroded connector

    Checks

    1. 1Unplug the accelerator position sensor 2 and check the signal wire for continuity to the ECU and for a short to ground
    2. 2Inspect the accelerator position sensor 2 connector for water, corrosion and pushed-back pins
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN91-FMI2Accelerator position sensor correlation error

    SPN 91 FMI 2 means the two accelerator position sensors do not agree with each other.· Erratic or implausible
    Check soon

    Causes

    • One sensor drifted or failed
    • Shared supply fault
    • Wiring fault

    Checks

    1. 1Read both values in Diagmaster and compare them
    2. 2Check the supply voltage at both sensors
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN91-FMI3Accelerator position sensor 1 - Short to battery

    SPN 91 FMI 3 means accelerator sensor 1 reads above its range.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to supply
    • Failed sensor
    • Connector fault

    Checks

    1. 1Read the throttle value in Diagmaster with the control at rest
    2. 2Check the signal wire for a short to a supply line
    3. 3Inspect the connector for water and corrosion
    4. 4Back-probe the sensor for a stable 5 V supply
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Kubota SPN91-FMI4Accelerator position sensor 1 - Ground short or open circuit

    SPN 91 FMI 4 means accelerator sensor 1 reads below its range, an open circuit or short to ground.· Shorted low
    Check soon

    Causes

    • Accelerator sensor failed
    • Sensor signal wire open or grounded
    • Connector fault

    Checks

    1. 1Read the throttle value in Diagmaster while moving the control
    2. 2Back-probe supply, ground and signal; expect about 5 V and a signal between roughly 0.5 and 4.5 V
    3. 3Check the wires for continuity and a short to ground
    4. 4Inspect the accelerator sensor connector for pushed-back pins and water
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Kubota SPN628-FMI2ECU flash ROM error

    SPN 628 FMI 2 means the ECU flash memory check failed.· Erratic or implausible
    Stop now

    Causes

    • ECU memory failure
    • Interrupted software load
    • Unstable supply voltage

    Checks

    1. 1Check the supply voltage and ECU fuses
    2. 2Have the ECU reflashed or replaced
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN1077-FMI2ECU CPU (main IC) error

    SPN 1077 FMI 2 means the main processor chip of the ECU reports an internal error.· Erratic or implausible
    Stop now

    Causes

    • ECU internal failure
    • Unstable supply voltage
    • Water damage

    Checks

    1. 1Check the supply voltage and earths
    2. 2Replace the ECU if the code returns after cycling the key
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota E:9121Engine ECU error

    The engine ECU has an internal fault.· Part or controller
    Stop now

    Causes

    • Engine ECU internal fault
    • Corrupted software
    • Power or ground fault

    Checks

    1. 1Check the ECU power and ground at its connector with a meter
    2. 2Inspect the ECU connectors for water and corrosion
    3. 3Recheck the ECU fuses and the main relay for voltage drop under load
    4. 4Reflash or replace the ECU through a Kubota dealer
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Kubota E:9122ECU communication failure

    The engine ECU and the machine controller cannot talk to each other.· Other
    Stop now

    Causes

    • CAN wiring fault
    • ECU power fault
    • ECU failure

    Checks

    1. 1Check the CAN wiring between engine ECU and machine controller for breaks and chafing
    2. 2Measure the CAN resistance at the diagnostic connector
    3. 3Check the engine ECU power supply and ground at its connector with key on
    4. 4Inspect the connectors for water and pushed-back pins
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota E:9400Other engine failures

    A general engine failure that does not fit any of the other E:9xxx codes.· Other
    Check soon

    Causes

    • Unspecified engine ECU fault
    • Stored engine DTC
    • Sensor fault
    • Software error

    Checks

    1. 1Read the stored codes with Diagmaster for the detail
    2. 2Inspect the engine harness and ECU connectors for damage and water
    3. 3Check the key sensors in Diagmaster for plausible, stable readings
    4. 4Contact a Kubota dealer with the codes you found
    5. 5Clear the codes and retest the machine to see which one returns first
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Kubota SPN523527-FMI2ECU CPU (monitoring IC) error

    SPN 523527 FMI 2 means the monitoring chip that watches the main processor reports an error.· Erratic or implausible
    Stop now

    Causes

    • ECU internal failure
    • Unstable supply voltage
    • Water damage

    Checks

    1. 1Check the supply voltage and earths
    2. 2Replace the ECU if the code returns after cycling the key
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523543-FMI2Accelerator position sensor error (CAN)

    SPN 523543 FMI 2 means the accelerator value received over CAN is not plausible.· Erratic or implausible
    Check soon

    Causes

    • CAN wiring fault between the controller and the ECU
    • Accelerator sensor fault at the machine controller
    • Connector fault

    Checks

    1. 1Check the CAN wiring and the accelerator sensor in the machine controller
    2. 2Read the accelerator value in Diagmaster
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523547-FMI2CAN2 bus off

    The ECU has stopped communicating on its CAN2 bus (bus off), so every frame carried there is lost at once.· Erratic or implausible
    Check soon

    Causes

    • Short or open on the CAN2 pair
    • Bus loaded down by a failed node

    Checks

    1. 1Measure CAN-H to CAN-L resistance on the CAN2 pair at the diagnostic connector.
    2. 2Unplug nodes one at a time to see whether the bus recovers.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523548-FMI2CAN-KBT frame error

    The frame sent by the Kubota machine controller (KBT) arrives damaged or incomplete, so the ECU ignores its content.· Erratic or implausible
    Check soon

    Causes

    • Machine controller not sending a valid KBT frame
    • Loose CAN connector

    Checks

    1. 1Connect Diagmaster and check whether the machine controller is listed as present.
    2. 2Reseat the machine controller connector and recheck.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523591-FMI2CAN CCVS (parking switch and vehicle speed) frame error

    The CCVS frame that carries the parking switch and vehicle speed is bad, so the ECU does not know if the machine is parked or moving.· Erratic or implausible
    Check soon

    Causes

    • Machine controller not sending CCVS
    • Parking switch or speed signal fault upstream

    Checks

    1. 1Watch the parking switch state in Diagmaster while applying the parking brake.
    2. 2Check the machine controller for its own speed or switch faults.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523592-FMI2CAN CM1 (regeneration switch) frame error

    The CM1 frame that carries the regeneration switch is bad, so pressing the switch has no effect on the ECU.· Erratic or implausible
    Check soon

    Causes

    • Machine controller not sending CM1
    • Regeneration switch wiring fault upstream

    Checks

    1. 1Press the regeneration switch and watch whether its state changes in Diagmaster.
    2. 2Check the switch connector at the machine controller.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523595-FMI2CAN ETC5 (neutral switch) frame error

    The ETC5 frame that carries the neutral switch is bad, so the ECU cannot tell whether the drive is in neutral.· Erratic or implausible
    Check soon

    Causes

    • Machine controller not sending ETC5
    • Neutral switch wiring fault upstream

    Checks

    1. 1Move the drive control to neutral and watch the neutral state in Diagmaster.
    2. 2Check the neutral switch connector and wiring to the machine controller.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523596-FMI2CAN TSC1 frame error

    The TSC1 frame that carries the engine speed request is bad, so the ECU ignores speed commands from the machine controller.· Erratic or implausible
    Check soon

    Causes

    • Machine controller not sending TSC1
    • Accelerator signal fault upstream

    Checks

    1. 1Move the accelerator and watch whether the requested speed follows in Diagmaster.
    2. 2Check the machine controller for accelerator codes of its own.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523598-FMI2CAN EBC1 frame error

    The EBC1 frame from the machine controller is bad, so the ECU loses that message and flags a data error.· Erratic or implausible
    Check soon

    Causes

    • Machine controller not sending EBC1
    • Intermittent contact in the CAN connector

    Checks

    1. 1Read the active frames in Diagmaster and confirm EBC1 is missing.
    2. 2Wiggle the CAN harness at the machine controller while watching the code.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523604-FMI2CAN1 bus off

    The ECU has gone bus off on its CAN1 bus, the main link to the machine controller, so the engine takes no requests from it.· Erratic or implausible
    Check soon

    Causes

    • CAN1 wire shorted or open
    • Terminating resistor missing or failed

    Checks

    1. 1Measure CAN-H to CAN-L resistance on CAN1 with the key off.
    2. 2Check the ECU and machine controller connectors on the CAN1 pair.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Kubota SPN523700-FMI13EEPROM check sum error

    SPN 523700 FMI 13 means the stored calibration data failed its check sum.· Part or controller
    Stop now

    Causes

    • Corrupted ECU memory
    • Interrupted programming
    • Supply voltage dropped during a write

    Checks

    1. 1Check the supply voltage
    2. 2Have the ECU reprogrammed
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

Shared checks

Checks, in order

  1. 1Check battery voltage and the ECU supply fuses
  2. 2Check the battery voltage and the ECU fuses and relay
  3. 3Measure the CAN-H to CAN-L resistance at the diagnostic connector
  4. 4Read both accelerator sensor values in Diagmaster and compare them
  5. 5Inspect the ECU connector for water and corrosion
  6. 6Check the connectors at the ECU and the machine controller
  7. 7Measure the 5 V supply at the sensor connector

Causes

  • Unspecified engine failure logged by the ECU
  • Low or unstable supply voltage
  • CAN wiring or connector fault between the ECU and the machine controller
  • CAN wiring or connector fault

Most codes here: erratic or implausible (13 of 21)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: The engine may not start or may stop by itself, with the engine ECU lamp on and a code stored.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.