John Deere · Main controller (MCZ) - options
John Deere Fault Code MCZ 11457.02
2-speed activation solenoid not detected
What does John Deere code MCZ 11457.02 mean?
The MCZ expects a 2-speed (combined pump flow) solenoid and cannot find it. If the machine does not have that kit, the code is a configuration leftover and can be cleared. Urgency: information - a reminder or status message. Check first: confirm whether the machine really has a 2-speed (combined flow) kit fitted.
- MCZ
- Which controller reports it
- 11457
- What is at fault
- .02
- How it failed
Can I keep running with it?
Information
A reminder or status message. Nothing is failing yet.
What should I check first?
Confirm whether the machine really has a 2-speed (combined flow) kit fitted
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- No 2-speed kit fitted but the controller is set up to expect one
- Open wire or unplugged connector to the 2-speed solenoid
- Failed solenoid coil
- Wrong controller option configuration after a controller swap
How it failed
You'll notice: The MCZ cannot find the 2-speed (combined flow) solenoid.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Dig, regeneration and travel speed solenoids
1 other code on this part is also lost message (MCZ 11458.02). When they show together, start at the wiring and connector they share.
- MCZ 11407.043-Spool solenoid valve unit (SG) feedback low inputOpen circuitCheck soon
- MCZ 11428.024-Spool solenoid valve unit (SD) abnormal feedbackOtherCheck soon
- MCZ 11428.034-Spool solenoid valve unit (SD) feedback high inputReal conditionCheck soon
- MCZ 11428.044-Spool solenoid valve unit (SD) feedback low inputReal conditionCheck soon
- MCZ 11457.022-speed activation solenoid not detectedLost messageInformation
- MCZ 11458.02Selector valve solenoid not detectedLost messageInformation
- MCZ 11948.02Power dig solenoid feedback current abnormalOtherCheck soon
- MCZ 11948.03Power dig solenoid feedback current highShorted highCheck soon
- MCZ 11948.04Power dig solenoid feedback current lowOpen circuitCheck soon
Show the other 14 codesHide the other codes
- MCZ 11402.02Dig regenerative solenoid feedback current abnormalOtherCheck soon
- MCZ 11402.03Dig regenerative solenoid feedback current highReal conditionCheck soon
- MCZ 11402.04Dig regenerative solenoid feedback current lowReal conditionCheck soon
- MCZ 11403.02Arm regenerative solenoid feedback current abnormalOtherCheck soon
- MCZ 11403.03Arm regenerative solenoid feedback current highReal conditionCheck soon
- MCZ 11403.04Arm regenerative solenoid feedback current lowReal conditionCheck soon
- MCZ 11404.02Power dig solenoid feedback current abnormalOtherCheck soon
- MCZ 11404.03Power dig solenoid feedback current highShorted highCheck soon
- MCZ 11404.04Power dig solenoid feedback current lowOpen circuitCheck soon
- MCZ 11405.02Travel speed solenoid feedback current abnormalOtherCheck soon
- MCZ 11405.03Travel speed solenoid feedback current highReal conditionCheck soon
- MCZ 11405.04Travel speed solenoid feedback current lowReal conditionCheck soon
- MCZ 11407.023-Spool solenoid valve unit (SG) abnormal feedbackOtherCheck soon
- MCZ 11407.033-Spool solenoid valve unit (SG) feedback high inputShorted highCheck soon
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists MCZ 11457.02 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
