John Deere · Engine control unit (ECU) - Cooling
John Deere Fault Code ECU 000111.01
Coolant level low
What does John Deere code ECU 000111.01 mean?
The coolant level sensor shows the coolant level is low. The operator may see a low coolant warning, and running on risks overheating and engine damage. Urgency: stop now - shut down and fix before working on. Check first: with the engine cold, check the coolant level in the surge tank and top it up with the correct coolant.
- ECU
- Which controller reports it
- 000111
- Engine coolant level
- .01
- Data below normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
With the engine cold, check the coolant level in the surge tank and top it up with the correct coolant
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Coolant level really low from a leak or an overdue top-up
- Radiator or surge tank cap not sealing and letting coolant out
- Coolant level sensor faulty or coated with deposits
- Level sensor wiring damaged
How it failed
You'll notice: The coolant level sensor says the coolant is low.
Real conditionRead from how the source describes the code
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine coolant, intake air and fuel temperature
1 other code on this part is also real condition (ECU 000111.07). When they show together, start at the wiring and connector they share.
- ECU 000110.04Engine coolant temperature low voltage inputShorted lowCheck soon
- ECU 000110.15Engine coolant temperature slightly highLost messageCheck soon
- ECU 000110.16Engine coolant temperature high: cool downLost messageCheck soon
- ECU 000110.17Engine coolant temperature low: warm upLost messageCheck soon
- ECU 000111.01Coolant level lowReal conditionStop now
- ECU 000111.07Coolant loss detectedReal conditionStop now
- ECU 000111.17Coolant level low (moderate)OtherCheck soon
- ECU 000111.18Coolant level low: moderately severe levelOtherCheck soon
- ECU 000174.00Fuel temperature highShorted highCheck soon
Show the other 11 codesHide the other codes
- ECU 000105.00Intake air temperature highShorted highCheck soon
- ECU 000105.04Intake air temperature signal faultErratic or implausibleCheck soon
- ECU 000105.15Intake air temperature high: cooling system dustLost messageCheck soon
- ECU 000105.16Intake manifold air temperature drastically highLost messageCheck soon
- ECU 000110.00Coolant temperature highShorted highStop now
- ECU 000110.03Engine coolant temperature signal highOtherCheck soon
- ECU 000174.03Fuel temperature sensor inaccessibleOtherCheck soon
- ECU 000174.04Fuel temperature signal voltage lowShorted lowCheck soon
- ECU 000174.16Fuel temperature increasedLost messageCheck soon
- ECU 003587.05Cold start aid solenoid open circuitOpen circuitCheck soon
- ECU 003587.06Cold start aid solenoid short circuitLost messageCheck soon
Other John Deere codes: Engine control unit (ECU) - Cooling
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists ECU 000111.01 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
