John Deere · Basic control unit (BCU) - tractor
John Deere Battery, alternator and tractor basic control unit (BCU) fault codes
The system voltage codes report a battery that is too low or too high, from the ECU and from the tractor BCU, and the monitor raises an alternator alarm when output is wrong. The BCU codes cover its internal fault and CAN link, the service interval reminders, the handbrake, the differential lock solenoid, the LTC coolant pump relay and the turn-signal switch.
Where this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
What do these codes mean?
John Deere codes BCU 000070.31 to BCU 302004.31 are all about the battery, alternator and tractor basic control unit (BCU). The most common failure type is shorted low (6 of 22); 4 need an immediate stop. Start with this check: measure battery voltage at rest and with the engine running; charging should be above rest voltage and not far over the manual limit.
How urgent are they?
4 of 22 codes here mean stop now; 14 can wait until the shift ends, but find the cause before the next one; 4 are information only.
- Stop now4
- Check soon14
- Info4
What should I check first?
Measure battery voltage at rest and with the engine running; charging should be above rest voltage and not far over the manual limit
Shared checks22 of 22
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
John Deere BCU 000070.31Handbrake fault
The BCU reports a problem with the handbrake (parking brake) circuit. The control unit cannot confirm the parking brake state, so the tractor may refuse to move, show a brake warning or not hold on a slope.· OtherOtherCheck soonCauses
- Parking brake switch worn, dirty or misadjusted
- Wiring or connector to the handbrake switch damaged or corroded
- Parking brake not fully released or applied
- BCU input fault when the switch and wiring test good
Checks
- 1Apply and release the handbrake and watch the brake input on the display; it must change cleanly
- 2Inspect the handbrake switch plug and wiring for corrosion, chafe and loose pins
- 3Check that the lever and linkage fully release and apply the brake
- 4Measure the switch circuit continuity in both lever positions and compare with the wiring diagram
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere ECU 000158.01Battery voltage low
The ECU sees its supply voltage drop below the lower limit. Low supply can set other communication codes, cause the engine to stall or restart poorly, and the operator may see a battery warning.· Shorted lowShorted lowCheck soonCauses
- Weak or discharged batteries
- Loose or corroded battery terminals or earth straps
- Alternator not charging
- High resistance in the ECU supply wire or fuse holder
Checks
- 1Measure battery voltage with the engine off and again with the engine running
- 2Check and clean battery terminals and the main earth strap
- 3Test the alternator output under load and check the belt tension and condition
- 4Voltage-drop test the ECU supply feed and ground circuits
- 5Load test the batteries if the voltage drops while cranking
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
John Deere ECU 000158.17Battery voltage low (power removed from ECU)
The ECU reports its supply was removed or fell low enough to count as a power loss, usually from a loose feed, a blown fuse or a failing relay.· Shorted lowShorted lowCheck soonCauses
- A real low condition on the machine, such as low level, low pressure or a cold engine, behind the battery voltage at the ECU
- The battery voltage at the ECU reading low because of a drifting sensor
- Supply or feed problem that holds the value down
Checks
- 1Confirm the real value with an independent gauge or by inspection before blaming the battery voltage at the ECU
- 2Look for related codes and for a physical cause such as a low level, leak or weak supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
John Deere BCU 000168.16System voltage too high with engine running
The tractor system voltage reading is above its normal range, so the controller reports a high value; this can be a real condition on the machine and not only a wiring fault.· Shorted highShorted highCheck soonCauses
- A real high condition on the machine, such as heat, load or restriction, behind the tractor system voltage
- The tractor system voltage reading high because of a drifting sensor
- Cooling, intake or supply problem that pushes the value up
Checks
- 1Confirm the real value with an independent gauge or thermometer before blaming the tractor system voltage
- 2Look for related codes and for a physical cause such as a blocked cooler or restriction
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
John Deere BCU 000168.17System voltage too low at about 1,500 rpm
The tractor system voltage reading is below its normal range, so the controller reports a low value; this can be a real condition on the machine and not only a wiring fault.· Shorted lowShorted lowCheck soonCauses
- A real low condition on the machine, such as low level, low pressure or a cold engine, behind the tractor system voltage
- The tractor system voltage reading low because of a drifting sensor
- Supply or feed problem that holds the value down
Checks
- 1Confirm the real value with an independent gauge or by inspection before blaming the tractor system voltage
- 2Look for related codes and for a physical cause such as a low level, leak or weak supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
John Deere BCU 000168.18System voltage too low above 1,500 rpm
The tractor system voltage reading is below its normal range, so the controller reports a low value; this can be a real condition on the machine and not only a wiring fault.· Shorted lowShorted lowCheck soonCauses
- A real low condition on the machine, such as low level, low pressure or a cold engine, behind the tractor system voltage
- The tractor system voltage reading low because of a drifting sensor
- Supply or feed problem that holds the value down
Checks
- 1Confirm the real value with an independent gauge or by inspection before blaming the tractor system voltage
- 2Look for related codes and for a physical cause such as a low level, leak or weak supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
John Deere ECU 000627.01Electronic injection voltage low
The injection supply voltage is below the ECU limit, so the injectors may not fire correctly.· Shorted lowShorted lowCheck soonCauses
- A real low condition on the machine, such as low level, low pressure or a cold engine, behind the battery voltage at the ECU
- The battery voltage at the ECU reading low because of a drifting sensor
- Supply or feed problem that holds the value down
Checks
- 1Confirm the real value with an independent gauge or by inspection before blaming the battery voltage at the ECU
- 2Look for related codes and for a physical cause such as a low level, leak or weak supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
John Deere ECU 000627.18Battery voltage below normal
The ECU saw its battery supply fall below normal. The operator may see a low voltage warning, and the engine may run poorly or set other communication codes.· Shorted lowShorted lowCheck soonCauses
- Batteries run low from short work cycles or a charging fault
- Poor battery or earth connections dropping voltage under load
- Alternator belt slipping or the alternator not keeping up
Checks
- 1Measure battery voltage at rest and again with the engine running at high idle
- 2Check the alternator belt tension and condition
- 3Clean the battery terminals and the earth straps at the engine and the frame
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
John Deere BCU 000629.12Control unit internal fault
The BCU reports an internal fault of the control unit itself, so it can no longer be trusted to run tractor functions.· Lost messageLost messageStop nowCauses
- Wiring or connector fault in the circuit behind this code
- The part or unit the code names failing
- Low or unstable supply voltage to the controller
Checks
- 1Check the connector and wiring behind this code for corrosion, oil and pins that are pushed out
- 2Measure supply voltage and ground at the controller and clear the code to see if it returns
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere BCU 000639.12Control unit interior system error
The BCU reports an interior system error inside the control unit, so its own checks failed.· OtherOtherStop nowCauses
- Wiring or connector fault in the circuit behind this code
- The part or unit the code names failing
- Low or unstable supply voltage to the controller
Checks
- 1Check the connector and wiring behind this code for corrosion, oil and pins that are pushed out
- 2Measure supply voltage and ground at the controller and clear the code to see if it returns
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere BCU 000639.1329-bit CAN bus high error rate
The controller does not receive the expected basic control unit (BCU) and its 29-bit CAN bus, or it arrives too slowly or with invalid data, so that data cannot be used.· Lost messageLost messageCheck soonCauses
- The unit that should send the basic control unit (BCU) and its 29-bit CAN bus is off, damaged or missing its power
- Broken, shorted or corroded CAN wire or connector between the units
- Missing or faulty CAN termination on the bus
Checks
- 1Check the power, ground and fuse of the unit that sends the basic control unit (BCU) and its 29-bit CAN bus before the CAN wiring
- 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere BCU 000639.1429-bit CAN bus higher error rate
The controller does not receive the expected basic control unit (BCU) and its 29-bit CAN bus, or it arrives too slowly or with invalid data, so that data cannot be used.· Lost messageLost messageCheck soonCauses
- The unit that should send the basic control unit (BCU) and its 29-bit CAN bus is off, damaged or missing its power
- Broken, shorted or corroded CAN wire or connector between the units
- Missing or faulty CAN termination on the bus
Checks
- 1Check the power, ground and fuse of the unit that sends the basic control unit (BCU) and its 29-bit CAN bus before the CAN wiring
- 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere BCU 000746.31Differential lock solenoid valve circuit fault
The BCU reports a circuit problem on the differential lock solenoid valve. The solenoid is driven open or shorted, so the differential lock may not engage when the operator presses the switch, or it may stay engaged.· OtherOtherCheck soonCauses
- Differential lock solenoid coil open or shorted
- Wire to the solenoid chafed or broken
- Connector at the solenoid corroded or loose
- BCU output stage failing
Checks
- 1Measure the differential lock solenoid coil resistance at its plug and compare with the manual value
- 2Inspect the solenoid harness and plug for chafe, corrosion and loose pins
- 3Operate the differential lock switch and watch the commanded output on the service screen
- 4Check the supply fuse for the solenoid before replacing the valve
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere BCU 001676.31LTC coolant pump relay circuit fault
The BCU reports a circuit error on the relay that switches the LTC coolant pump. The relay or its wiring is open or shorted, so the pump may not run when the controller commands it, which risks heat build up in the circuit it cools.· OtherOtherCheck soonCauses
- Coolant pump relay failed or stuck
- Relay socket or its connector corroded or loose
- Wire between the BCU and the relay chafed or broken
- Pump itself drawing too much current and burning the relay
Checks
- 1Swap the relay with a similar one in the fuse box and see whether the code clears
- 2Inspect the relay socket and the pump plug for corrosion and burnt terminals
- 3Measure the relay coil circuit continuity from the BCU with the plugs removed
- 4Check that the coolant pump turns freely and runs when commanded
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere DSZ 13304.02Alternator alarm (output above 33.5 V)
The monitor saw charging voltage above 33.5 V on the 24 V system. Overcharging can damage batteries and electronics, and the operator may see a battery or alternator warning.· Lost messageLost messageStop nowCauses
- Alternator regulator failed high
- Loose battery or sense wire at the alternator
- Faulty battery connection causing the regulator to over-correct
Checks
- 1Measure battery voltage with the engine running at idle and at high speed
- 2Check the alternator output wire and sense wire connections
- 3Check battery terminals and earth straps for corrosion
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ICZ 13304.02Alternator alarm (output above 33.5 V)
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The monitor saw charging voltage above 33.5 V on the 24 V system. Overcharging can damage batteries and electronics, and the operator may see a battery or alternator warning.· Lost messageLost messageStop nowCauses
- Alternator regulator failed high
- Loose battery or sense wire at the alternator
- Faulty battery connection causing the regulator to over-correct
Checks
- 1Measure battery voltage with the engine running at idle and at high speed
- 2Check the alternator output wire and sense wire connections
- 3Check battery terminals and earth straps for corrosion
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ICZ 20103.02Alternator alarm
The monitor raises the Alternator alarm warning, which means the condition it watches on the alternator charging is outside its normal state or the input to it is faulty.· OtherOtherCheck soonCauses
- The real condition the alternator charging monitors is present
- Switch or sensor of the alternator charging failing or wired wrongly
- Harness or connector fault between the input and the monitor
Checks
- 1Confirm the real condition at the alternator charging on the machine before replacing parts
- 2Check the switch or sensor plug and wiring for the alternator charging
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere BCU 299780.07Turn-signal switch fault
The BCU reports a fault on the turn-signal switch. The switch gives a signal the control unit does not accept as valid, so the indicators may not flash, may flash on one side only or stay on.· OtherOtherCheck soonCauses
- Turn-signal switch worn or stuck
- Switch connector corroded or loose
- Wiring between the switch and the BCU chafed
- BCU input fault when the switch tests good
Checks
- 1Operate the turn-signal switch in each position and watch its input on the display
- 2Inspect the switch plug under the steering column for corrosion and loose pins
- 3Check the wiring from the switch to the BCU for chafe where it passes the steering column
- 4Measure the switch contacts for continuity in each position against the wiring diagram
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere BCU 302001.31Service interval reminder: 250 hours
The controller has set a condition code for the service interval reminder: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part.· OtherOtherInfoCauses
- The real condition behind the service interval reminder is present
- A related component or circuit that causes the condition
- The message or reminder was not reset after the earlier service
Checks
- 1Confirm on the machine that the condition behind the service interval reminder is real and act on it
- 2Read all other codes active at the same time, since this one is often a consequence of another fault
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere BCU 302002.31Service interval reminder: 500 hours
The controller has set a condition code for the service interval reminder: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part.· OtherOtherInfoCauses
- The real condition behind the service interval reminder is present
- A related component or circuit that causes the condition
- The message or reminder was not reset after the earlier service
Checks
- 1Confirm on the machine that the condition behind the service interval reminder is real and act on it
- 2Read all other codes active at the same time, since this one is often a consequence of another fault
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere BCU 302003.31Service interval reminder: 750 hours
The controller has set a condition code for the service interval reminder: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part.· OtherOtherInfoCauses
- The real condition behind the service interval reminder is present
- A related component or circuit that causes the condition
- The message or reminder was not reset after the earlier service
Checks
- 1Confirm on the machine that the condition behind the service interval reminder is real and act on it
- 2Read all other codes active at the same time, since this one is often a consequence of another fault
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere BCU 302004.31Service interval reminder: 1,500 hours
The controller has set a condition code for the service interval reminder: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part.· OtherOtherInfoCauses
- The real condition behind the service interval reminder is present
- A related component or circuit that causes the condition
- The message or reminder was not reset after the earlier service
Checks
- 1Confirm on the machine that the condition behind the service interval reminder is real and act on it
- 2Read all other codes active at the same time, since this one is often a consequence of another fault
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Measure battery voltage at rest and with the engine running; charging should be above rest voltage and not far over the manual limit
- 2Clean and tighten the battery and ground cable ends before anything else
- 3Clear the service reminder only after the service is done, using the monitor procedure
- 4For a function code check the solenoid, relay or switch it names and its wiring with both ends unplugged
- 5Read other active codes: voltage faults often set many other codes at once
Causes
- Battery weak, loose terminals or a corroded ground cable
- Alternator or its regulator not charging, or charging too high
- Wiring fault or failed relay or solenoid in the circuit the BCU names
- Controller internal fault or CAN link problem
Most common here: shorted low (6 of 22)
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
When to stop
You'll notice: Charging problems can reset controllers and set many unrelated codes; a BCU function fault disables the one function, and a service reminder only tells you maintenance is due.
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
- Inside the Yard - John Deere fault codes list (ECU engine codes)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
