EF Logo

JLG · Platform / ground controls

JLG Footswitch, joysticks, steer switches and start sequence fault codes

These are the operator inputs of a JLG boom lift: the footswitch and keyswitch, the drive and steer joystick, the lift and swing joystick, the steer switches, the function switches with the ground enable, and the start-up order checks that lock a switch out if it was used too early. The platform and ground modules read each one and report a fault when a contact disagrees with its partner, sticks, or is used out of sequence.

FaultCheck2-1JLG · Footswitch, joysticks, steer switches and start sequence
Code shows hereFAULT2-1

Where this code shows

Turn the key on and watch the fault lamp or platform display.

What do these codes mean?

JLG codes 2-1 to 2310 are all about the footswitch, joysticks, steer switches and start sequence. The most common failure type is real condition (4 of 26); none needs an immediate stop. Start with this check: read the Help message on the analyzer to see which input is named.

How urgent are they?

None of the 26 codes here means stop now; 24 can wait until the shift ends, but find the cause before the next one; 2 are information only.

  • Check soon24
  • Info2

What should I check first?

Read the Help message on the analyzer to see which input is named

Shared checks

26 of 26

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JLG 2-1Footswitch or keyswitch fault

    The controller sees the two footswitch contacts reading the same state for over a second, or the keyswitch input is invalid.· Real condition
    Check soon

    Causes

    • Footswitch with one contact stuck or worn so both channels agree
    • Broken or pinched footswitch cable inside the platform control box
    • Corroded platform module connector at the footswitch input
    • Keyswitch contacts worn or key left between positions
    • Platform module input damaged (rare)

    Checks

    1. 1Read the Help message on the analyzer: FSW FAULTY or KEYSWITCH FAULTY
    2. 2Open the platform box and check the two footswitch wires change state opposite to each other when pressed and released
    3. 3Ohm the footswitch cable end to end and wiggle it while watching the analyzer
    4. 4Clean and reseat the platform module connector
    5. 5Cycle the EMS button, then retest; replace the footswitch if the fault returns
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JLG 2-2Drive or steer selection fault

    The drive or steer inputs are in a state the controller will not accept: joystick moved before the footswitch, steer selected before the footswitch, both steer switches active, or the joystick signal out of range.· Other
    Check soon

    Causes

    • Operator moved the drive joystick or steer switch before pressing the footswitch
    • Footswitch held closed about 7 seconds with nothing selected
    • Drive joystick centre tap voltage outside its window (resistive about 3.08-3.83 V, inductive about 2.18-2.70 V)
    • Q-Prox sensor on an inductive joystick reading above about 3.18 V, or joystick not neutral
    • Steer rocker switches stuck or wiring shorted

    Checks

    1. 1Release everything, let the footswitch open, then press the footswitch first and select drive after
    2. 2Read the Help message to see which variant it is (D/S JOY. CENTER TAP BAD, OUT OF RANGE, STEER SWITCHES FAULTY)
    3. 3Measure joystick supply and centre tap at the platform module with the joystick untouched
    4. 4Check the 7 V sensor reference is steady and not shorted
    5. 5Replace the drive joystick if the centre tap stays out of window
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2-3Boom function selection fault

    A boom function (lift, swing, telescope, jib, level, rotate) was selected in the wrong order or its joystick or switch is bad: both directions at once, selected before key or footswitch, or selected before aux power.· Other
    Check soon

    Causes

    • Function switch or lift/swing joystick moved before the footswitch or key was on
    • Both directions of one function closed together (stuck rocker)
    • Lift/swing joystick centre tap out of window or Q-Prox sensor fault
    • Ground function selected before aux power was applied
    • Water in the platform control box shorting switch inputs

    Checks

    1. 1Release all functions, cycle the footswitch and retry in the correct order
    2. 2Use the analyzer diagnostics menu to find which input shows active with nothing pressed
    3. 3Check the suspect switch contacts with a meter at the platform box terminals
    4. 4Measure the lift/swing joystick centre tap at rest
    5. 5Dry out and reseal the platform box; replace the joystick or switch found faulty
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2-4Steering digital inputs faulty

    The steering digital inputs do not make sense to the controller.· Other
    Check soon

    Causes

    • Steer rocker or switch contacts worn so both directions read as pressed
    • Platform harness chafed or pinched near the steer switch
    • Moisture or corrosion in the platform control box on the steer inputs
    • Steer input stuck active from a failed rocker spring

    Checks

    1. 1Read the Help message on the analyzer and note which steer input is named
    2. 2Open the diagnostics screen and watch both steer inputs while the switch is pushed each way
    3. 3Ohm the steer switch in each position with the wires removed; the two inputs should never read closed together
    4. 4Inspect the platform harness connector for water, loose pins and rub marks on the cable
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2-7Accelerator input faulty

    The ground or platform module sees the accelerator (throttle) input as invalid, so it cannot trust the engine speed request.· Other
    Check soon

    Causes

    • Throttle or accelerator switch/pot with a worn or open contact
    • Harness between the throttle device and the platform or ground module chafed or broken
    • Corroded or loose pin in the module connector for the throttle input
    • Throttle actuator or its feedback circuit damaged on the engine
    • Module input stage damaged (least likely)

    Checks

    1. 1Plug in the analyzer, read the Help message and note which module (ground or platform) is reporting the accelerator input
    2. 2Open the analyzer diagnostics and watch the throttle input while moving the throttle switch through each position; it should change cleanly
    3. 3With the connector unplugged, check the wires from the throttle device to the module pins for continuity and for shorts to each other or to chassis
    4. 4Clean and reseat the module connector, looking for pushed-back or green pins at the throttle input
    5. 5Swap in a known good throttle switch or pot to separate a device fault from a wiring fault, and replace the faulty part
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 0011Footswitch open

    The controller reports the footswitch input as open, which is the normal state with the pedal released.· Other
    Info

    Causes

    • Pedal released as normal
    • Pedal contacts or cable open so the controller never sees it closed

    Checks

    1. 1Press the pedal and watch the footswitch input in the analyzer change to closed
    2. 2If it never closes, ohm the pedal cable and check the plug in the platform box
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 213Footswitch faulty

    The two footswitch signals have been in the same state for too long, so the controller judges the footswitch faulty.· Other
    Check soon

    Causes

    • Footswitch contact stuck or worn so both signals match
    • Footswitch cable pinched or broken inside the platform box
    • Platform module connector corroded at the footswitch pins
    • Water in the platform control box
    • Platform module input fault

    Checks

    1. 1Watch both footswitch inputs in the analyzer diagnostics; they should switch in opposite states as the pedal is pressed and released
    2. 2Ohm each footswitch contact in both positions with the cable disconnected from the module
    3. 3Flex the footswitch cable along its length while watching the analyzer for dropouts
    4. 4Open the platform box and check for water, corrosion and loose pins on the connector
    5. 5Recycle the EMS button, retest, and replace the footswitch if the fault comes back
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 224Function problem - Steer left permanently selected

    The steer left input reads as selected with nobody pressing it, so the controller treats it as stuck on and may block steering or other functions.· Other
    Check soon

    Causes

    • Steer left switch jammed or sticking
    • Steer left wire shorted to a supply wire

    Checks

    1. 1Release the switch and read the steer left input in the analyzer
    2. 2Unplug the switch and see whether the input clears
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 225Function problem - Steer right permanently selected

    The steer right input reads as selected with nobody pressing it, so the controller treats it as stuck on and may block steering or other functions.· Other
    Check soon

    Causes

    • Steer right switch jammed or sticking
    • Steer right wire shorted to a supply wire

    Checks

    1. 1Release the switch and read the steer right input in the analyzer
    2. 2Unplug the switch and see whether the input clears
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 227Steer switches faulty

    The controller finds the steer switch pair unreliable, for example left and right selected together, so steering is blocked until the inputs read sensibly.· Real condition
    Check soon

    Causes

    • Left and right wires shorted together
    • Switch damaged so both contacts close together

    Checks

    1. 1Check that only one steer input changes when each direction is pressed
    2. 2Check the switch wiring between the switch and the module
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JLG 234Function switches faulty - Check diagnostics/boom

    The controller thinks the function switches are faulty and tells you to check the boom function menu in diagnostics.· Real condition
    Check soon

    Causes

    • Function switch stuck in the on position
    • Water in the platform control box
    • Harness short between two function switch wires
    • Corroded connector at the platform module

    Checks

    1. 1Open the analyzer diagnostics boom menu and look for any input showing active with nothing pressed
    2. 2Press each function switch and watch its input change, noting any that stay on or flicker
    3. 3Check the offending switch with a meter for continuity in each position
    4. 4Open the platform box, look for moisture and corrosion, and dry and reseal it
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JLG 235Function switches locked - Selected before aux power

    A function switch was selected before auxiliary power was switched on, so the controller locks that function until everything is released and the aux power sequence is repeated.· Other
    Check soon

    Causes

    • Function switch held while aux power was being selected
    • Aux power switch contact slow to close so the function input arrives first

    Checks

    1. 1Release the function switches, select aux power, then select the function
    2. 2Read the aux power input in the analyzer while operating the switch to confirm it registers cleanly
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 236Function switches locked - Selected before start switch

    A function switch was selected before the start switch was used, so the controller locks it until switches are released and the start sequence repeated.· Other
    Check soon

    Causes

    • Function switch left selected while the start switch was operated
    • Start switch contacts dirty so it registers after the function

    Checks

    1. 1Release all function switches, press start, then select the function
    2. 2Read the start input in the analyzer and check it changes the moment the switch is pressed
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 237Start switch locked - Selected before keyswitch

    The start switch was selected before the keyswitch was in position, so the start is locked until the switches are released and the key used first.· Other
    Check soon

    Causes

    • Start switch held while the key was still being turned
    • Keyswitch slow to reach its run position because of worn contacts

    Checks

    1. 1Release the start switch, turn the key fully to run, then press start
    2. 2Read the keyswitch input in the analyzer and check it shows on before the start input changes
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2211Footswitch interlock tripped

    The footswitch interlock tripped, for example the footswitch was closed with no function selected for too long, or closed at an unexpected time.· Real condition
    Check soon

    Causes

    • Footswitch held down at power-up or for too long with nothing selected
    • A joystick or function switch stuck in a selected state
    • Worn footswitch contact making a noisy, on-off signal
    • Water or corrosion in the platform control box
    • Footswitch cable chafed where it enters the box

    Checks

    1. 1Release the footswitch and the stick, cycle power and retry in the right order
    2. 2Open the analyzer diagnostics and check that no function input is active with everything released
    3. 3Ohm and flex the footswitch cable and contacts for an intermittent break
    4. 4Inspect the platform box for moisture and reseat the module connector
    5. 5Replace the footswitch or the stuck function switch if the fault repeats
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JLG 2212Drive locked - Joystick moved before footswitch

    The drive stick was off centre when the footswitch was pressed, so the controller locked drive until you let go of the stick and start again in order.· Other
    Check soon

    Causes

    • Operator put the drive stick forward while the foot was still off the pedal
    • Drive stick not centring because its spring or boot is binding

    Checks

    1. 1Return the drive stick to centre, release the pedal and press the pedal first before moving the stick
    2. 2With the stick at rest read the drive axis in the analyzer; any value away from zero means the stick itself is the fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2213Steer locked - Selected before footswitch

    A steer switch was already pressed when the footswitch went down, so the controller locked steering until all steer switches are released and the pedal sequence is repeated.· Other
    Check soon

    Causes

    • Steer thumb switch on the drive stick pressed or sticking as the pedal went down
    • Steer rocker contact closed by dirt so it looks pressed at start-up

    Checks

    1. 1Release both steer switches, release the pedal, then press the pedal before steering
    2. 2Read the steer inputs at rest in the analyzer and find the one showing selected
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2216Drive/steer joystick out of range high

    The drive/steer joystick signal is above its valid window, for example because the sensor reference is out of tolerance or a signal wire is shorted to battery.· Shorted high
    Check soon

    Causes

    • Drive joystick signal wire touching the battery supply at the joystick plug or in the platform cable
    • 7 V sensor reference pulled out of tolerance by a short on another sensor sharing the feed
    • Drive joystick damaged internally and reading above its window with the stick released
    • Cable chafed where it enters the platform control box

    Checks

    1. 1Read the drive joystick signal and the reference in the analyzer and compare with the manual values for a resistive or inductive joystick
    2. 2Measure the reference at the platform module; unplug other sensors on the same feed to find a short pulling it off
    3. 3Inspect the joystick cable and connector for a pin touching the supply
    4. 4Check the output with the stick released and then moved; it should rise smoothly
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JLG 2217Drive/steer joystick centre tap bad

    The drive/steer joystick centre tap is outside its allowed window (resistive about 3.08-3.83 V, inductive about 2.18-2.70 V).· Other
    Check soon

    Causes

    • Drive stick spring or boot damaged, so the stick does not come back to the exact neutral point the controller wants
    • Worn track or sensor in the drive joystick, giving a centre voltage outside about 3.08-3.83 V on a resistive stick or 2.18-2.70 V on an inductive one
    • Corroded pins at the drive joystick plug adding resistance to the centre-tap wire
    • Platform module reference supply too high or too low, shifting the whole window

    Checks

    1. 1Let go of the drive stick and read the centre tap in diagnostics, then compare with the window for the joystick fitted
    2. 2Push the stick through neutral by hand and see whether the boot or the spring holds it off centre
    3. 3Measure the reference supply at the platform module with the stick untouched
    4. 4Look at the drive joystick plug and the platform module pins for green corrosion
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2219Lift/swing joystick out of range high

    The lift/swing joystick signal is above its valid window, so the controller blocks boom lift and swing until it returns to range.· Other
    Check soon

    Causes

    • Lift/swing stick signal wire touching battery supply inside the platform control box
    • Shared sensor reference out of tolerance because of a short elsewhere on the same feed
    • Lift/swing joystick failed internally and now reads high even when released
    • Platform box cable or connector damaged, putting a live pin against the signal pin

    Checks

    1. 1With the stick released, read the lift/swing signal in diagnostics and compare it with the manual values for the fitted joystick
    2. 2Unplug other sensors one at a time while watching the reference at the platform module to find a short dragging it up
    3. 3Inspect the lift/swing joystick cable and plug for a chafed wire against a supply
    4. 4Move the stick slowly through its travel; the reading should move smoothly and not jump in steps
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2220Lift/swing joystick centre tap bad

    The lift/swing joystick centre tap is outside its allowed voltage window, so the controller will not accept the stick as neutral.· Other
    Check soon

    Causes

    • Boom joystick that no longer centres, with a weak spring or a boot caught by the control box
    • Track or sensor inside the lift/swing joystick worn, giving a centre voltage outside the window
    • High resistance in the lift/swing joystick plug or the wires to the platform module
    • Reference supply to the sensor off from a fault on the same feed

    Checks

    1. 1Release the lift/swing stick and read its centre tap in diagnostics against the window for the fitted joystick
    2. 2Make sure the stick returns freely to neutral and nothing in the control box is pressing on it
    3. 3Measure the sensor reference at the platform module with the stick at rest
    4. 4Check the plug and wires between the joystick and the platform module for corrosion and a backed-out pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2221Lift/swing locked - Joystick moved before footswitch

    The lift and swing stick was off centre when the footswitch was pressed, so lift and swing stay locked until the stick is released and the sequence repeated.· Other
    Check soon

    Causes

    • Operator moved the lift or swing stick before the pedal was pressed
    • Lift and swing stick not springing back to its centre notch

    Checks

    1. 1Centre the lift and swing stick, lift your foot and press the pedal before touching the stick
    2. 2Watch the lift and swing axes in the analyzer with the stick released; they should rest at zero
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2222Waiting for footswitch to be open

    The controller will not carry on until the footswitch is released, which makes the operator lift off the pedal before starting again.· Other
    Info

    Causes

    • Pedal held down at power-up or after a lockout
    • Pedal contacts stuck closed

    Checks

    1. 1Take your foot off the pedal and wait for the message to clear
    2. 2If the input stays closed with the pedal released, test the pedal and its cable
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2223Function switches locked - Selected before enable

    A function switch was selected before the enable was given, so the controller locks that function until everything is released and enable is applied first.· Other
    Check soon

    Causes

    • Function rocker held while the enable trigger was still open
    • Enable trigger worn so it registers late compared with the function switch

    Checks

    1. 1Release every function switch, press the enable, then select the function
    2. 2Read the enable input in the analyzer while squeezing the trigger and watch whether it changes before the function input does
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2224Footswitch selected before start

    The footswitch was pressed before the start sequence was complete, so platform functions stay locked until the pedal is released and the start repeated.· Other
    Check soon

    Causes

    • Operator standing on the pedal while turning the key or pressing start
    • Footswitch contact stuck closed so it looks pressed at power-up

    Checks

    1. 1Take your foot off the pedal, cycle the key and start, then press the pedal last
    2. 2With the key on and nobody on the pedal read the footswitch input; if it shows pressed the footswitch is the fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 2310Function problem - Ground enable permanently selected

    The ground enable input reads as selected while nobody is pressing it, so the controller treats it as stuck on and may lock ground control functions or the platform sequence.· Other
    Check soon

    Causes

    • Ground enable switch jammed or not returning
    • Ground enable wire shorted to a supply wire

    Checks

    1. 1With everything released, read the ground enable input in the analyzer and see whether it shows selected
    2. 2Unplug the enable switch; if the input clears the switch is at fault, if not suspect the wiring or module
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Read the Help message on the analyzer to see which input is named
  2. 2Release every stick, switch and the pedal, cycle the key and repeat the start-up in the right order
  3. 3With all controls at rest read the input in the analyzer; one that does not rest at zero is the faulty part
  4. 4Open the control box and look for moisture, bent levers, pinched cable and green pins
  5. 5Replace the part that disagrees with its partner, then cycle EMS

Causes

  • A worn or jammed footswitch, joystick or rocker that no longer returns to centre
  • Broken or pinched cable inside the platform control box
  • Corroded connector at the platform module input
  • Operator selecting a function before the step it depends on (key, start, enable, pedal)

Most common here: real condition (4 of 26)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The platform controls go dead or one function stays locked while the fault lamp flashes the code.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.