EF Logo

JLG · Engine

JLG Engine speed, temperature, oil pressure, fuel level and ECM fault codes

The JLG control system reads the engine through its own sensors: the fuel level sender, the engine speed sensor, coolant temperature, oil pressure, and messages from the engine control module. A shutdown or warning follows when one of them reads out of range or goes missing.

FaultStop4-2JLG · Engine speed, temperature, oil pressure, fuel level and ECM
Code shows hereFAULT4-2

Where this code shows

Turn the key on and watch the fault lamp or platform display.

What do these codes mean?

JLG codes 4-2 to 4323 are all about the engine speed, temperature, oil pressure, fuel level and ECM. The most common failure type is shorted low (3 of 15); 3 need an immediate stop. Start with this check: read the sensor value in the analyzer and compare with the gauge or a known reading.

How urgent are they?

3 of 15 codes here mean stop now; the other 12 can wait until the shift ends, but find the cause before the next one.

  • Stop now3
  • Check soon12

What should I check first?

Read the sensor value in the analyzer and compare with the gauge or a known reading

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JLG 4-2Engine over temperature

    Engine coolant is hotter than the limit (above about 117 C on Ford engines, above 130 C on Deutz).· Real condition
    Stop now

    Causes

    • Coolant low from a leak or a loose hose clamp
    • Radiator fins or oil cooler blocked with dirt and chaff
    • Fan belt slipping or broken, or an electric fan that is not running
    • Thermostat stuck closed so the coolant does not circulate
    • Coolant temperature sender reading too high

    Checks

    1. 1Let the engine cool, then check the coolant level and look for leaks around the radiator and hoses
    2. 2Blow out the radiator and oil cooler and check the fins are not blocked
    3. 3Check the fan belt tension and condition, or the electric fan wiring and relay
    4. 4Compare the temperature on the analyzer with an infrared gun reading on the engine to check the sender
    5. 5Test the thermostat in hot water and replace it if it does not open
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JLG 4-3Engine fault

    Covers engine help messages: high engine temp, air filter bypassed, no alternator output (battery still under 12.5 V after 15 s running), low oil pressure, oil/coolant/fuel sensor shorts, Ford ECM codes passed through, and lost RS-485 link to a Ford ECM.· Other
    Check soon

    Causes

    • Low oil level or a failed oil pressure sender (Deutz low pressure shows under about 8 PSI)
    • Alternator not charging or the belt slipping
    • Air filter restriction switch tripped by a clogged filter
    • Sensor wiring shorted to ground or battery on oil, coolant or fuel inputs
    • Ford ECM fault code stored, or the RS-485 link to the ECM lost

    Checks

    1. 1Read the Help message to see the exact engine item named
    2. 2Check the oil level and measure oil pressure with a mechanical gauge
    3. 3Measure charging voltage at the battery with the engine running
    4. 4Check the air filter restriction switch and its wire, and replace a clogged element
    5. 5For a Ford fault code, read the code from the ECM and diagnose it there
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 5-5Engine RPM / speed sensor problem

    On diesel machines the controller sees an invalid engine speed (over about 4000 RPM, roughly 8875 Hz) or no speed signal while oil pressure is above 8 PSI for 3 s.· Other
    Check soon

    Causes

    • Engine speed pickup faulty or set at the wrong gap from the flywheel
    • Wiring fault at the ground module speed input, open or shorted
    • Pickup wire picking up noise from the alternator or ignition wiring
    • Engine stalled while the oil pressure input still reads good

    Checks

    1. 1Check the Help message for SPEED SENSOR READING INVALID or SPEED INPUT LOST
    2. 2Inspect the speed sensor connector and wire to the ground module for damage
    3. 3Measure the pickup resistance and the air gap to the flywheel against the manual
    4. 4Look for a noise source near the sensor wire and re-route if it runs along the alternator lead
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 0031Fuel level low - Engine shutdown

    The fuel level input has fallen below the shutdown limit, so the controller shuts the engine down to stop it running dry.· Lost message
    Check soon

    Causes

    • Tank genuinely low on fuel
    • Fuel sender reading low from a stuck float or a poor connection

    Checks

    1. 1Dip the tank and compare with the gauge; refuel and restart if it is really low
    2. 2If the tank is full, test the sender and its wire as for the fuel sender family above
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JLG 431Fuel Sensor - Short to battery

    The controller reads battery voltage on the fuel sensor output while it is commanded off, so the circuit is shorted to battery.· Shorted high
    Check soon

    Causes

    • Fuel level sender signal wire shorted to a supply wire at the tank where the sender wire is exposed to fuel and vibration
    • Fuel sender float arm stuck at the top of the tank or the sender element open, so the gauge sticks at full
    • Sender element in the fuel level sender open or shorted high
    • Open ground or return wire at the fuel level sender, letting the signal float to supply

    Checks

    1. 1Unplug the fuel level sender in the fuel tank and measure the signal wire with the key on; battery voltage means a short to supply
    2. 2Check the ground and return continuity from the fuel level sender back to the module with the plug off
    3. 3Inspect the harness at the tank where the sender wire is exposed to fuel and vibration for rub marks that could touch a supply feed
    4. 4Dip the tank and compare with the gauge; a wrong gauge with the sender unplugged proves the signal is stuck
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JLG 432Fuel Sensor - Short to ground

    The controller sees the fuel sensor output pulled low while it is commanded on, so the circuit is shorted to ground.· Shorted low
    Check soon

    Causes

    • Signal wire of the fuel level sender rubbed through to earth at the tank where the sender wire is exposed to fuel and vibration
    • Fuel sender wire shorted to the tank or chassis, so the gauge sticks at empty
    • Sender element in the fuel level sender shorted low
    • Open supply or 5 V reference to the fuel level sender

    Checks

    1. 1Unplug the fuel level sender in the fuel tank and check the signal wire to the frame for continuity; there should be none
    2. 2Measure the reference supply (about 5 V) at the fuel level sender plug with the key on
    3. 3Look at the plug for a loose connector, pushed-back pins, water or corrosion
    4. 4With the sender plug off, a gauge that reads empty means the signal is held at ground in the wiring
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JLG 433Oil Pressure - Short to battery

    The controller reads battery voltage on the oil pressure output while it is commanded off, so the circuit is shorted to battery.· Shorted high
    Check soon

    Causes

    • Oil pressure sender signal wire shorted to a supply wire on the engine where heat and oil attack the sender wire
    • Oil pressure sender stuck at maximum or its signal touching a supply wire, so low pressure protection is blind
    • Oil pressure sender failed internally and now reads at the top of its range
    • Broken ground wire to the oil pressure sender so the signal cannot be pulled down

    Checks

    1. 1Unplug the oil pressure sender on the engine block and measure the signal wire with the key on; battery voltage means a short to supply
    2. 2Check the ground and return continuity from the oil pressure sender back to the module with the plug off
    3. 3Inspect the harness on the engine where heat and oil attack the sender wire for rub marks that could touch a supply feed
    4. 4With the key on and the engine stopped the reading should be near zero; a maximum reading then shows the signal is stuck high
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JLG 434Oil Pressure - Short to ground

    The controller sees the oil pressure output pulled low while it is commanded on, so the circuit is shorted to ground.· Shorted low
    Check soon

    Causes

    • Signal wire of the oil pressure sender rubbed through to earth on the engine where heat and oil attack the sender wire
    • Oil pressure sender shorted to ground internally or its wire rubbed through, so the engine thinks it has no oil pressure
    • Oil pressure sender failed internally and now reads at the bottom of its range
    • Missing 5 V reference at the oil pressure sender plug

    Checks

    1. 1Unplug the oil pressure sender on the engine block and check the signal wire to the frame for continuity; there should be none
    2. 2Measure the reference supply (about 5 V) at the oil pressure sender plug with the key on
    3. 3Look at the plug for a loose connector, pushed-back pins, water or corrosion
    4. 4Check with a mechanical gauge before blaming the engine: if real pressure is good, the sender or its wire is the fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JLG 435Coolant Temperature - Short to ground

    The controller sees the coolant temperature output pulled low while it is commanded on, so the circuit is shorted to ground.· Shorted low
    Check soon

    Causes

    • Coolant temperature sender signal wire chafed to the frame on the engine where heat hardens the sender wire
    • Coolant temperature sender wire rubbed to the engine block, so the reading sits at the cold end
    • Sender element in the coolant temperature sender shorted low
    • Open supply or 5 V reference to the coolant temperature sender

    Checks

    1. 1Unplug the coolant temperature sender on the engine and check the signal wire to the frame for continuity; there should be none
    2. 2Measure the reference supply (about 5 V) at the coolant temperature sender plug with the key on
    3. 3Look at the plug for a loose connector, pushed-back pins, water or corrosion
    4. 4A reading that stays cold while the engine is hot to the touch points at the sender signal shorted to ground
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JLG 437Engine trouble code

    The engine control module has stored a trouble code of its own, which the machine controller passes on as a general engine fault message.· Other
    Check soon

    Causes

    • Fault stored in the engine ECM
    • Engine sensor or actuator fault

    Checks

    1. 1Read the stored engine code with the engine diagnostic tool
    2. 2Fix that fault and clear it
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 438High engine temperature

    Engine coolant temperature is above its limit (about 117 C Ford, 130 C Deutz).· Real condition
    Stop now

    Causes

    • Low coolant level or a leak
    • Radiator fins blocked with dirt or chaff
    • Cooling fan or drive belt failed
    • Thermostat stuck closed
    • Coolant temperature sensor reading high

    Checks

    1. 1Stop the engine and let it cool before opening the cap, then check the coolant level and look for leaks
    2. 2Clean the radiator and charge air cooler fins and check airflow is not blocked
    3. 3Check the fan, fan drive and belt tension and condition
    4. 4Compare the temperature on the analyzer with an infrared reading on the engine to check the sensor
    5. 5Test the thermostat and replace it or the sensor if either is faulty
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JLG 4311Low oil pressure

    Engine oil pressure is low (Deutz: under about 8 PSI after 10 s of running).· Other
    Stop now

    Causes

    • Low engine oil level
    • Worn engine bearings or oil pump
    • Faulty oil pressure sender
    • Wiring to the oil pressure sender damaged
    • Oil too thin or wrong grade after a top-up

    Checks

    1. 1Shut the engine down and check the oil level on the dipstick and top up if low
    2. 2Fit a mechanical gauge to the oil pressure port and compare with the engine specification
    3. 3Check the sender connector and wire for corrosion and chafing
    4. 4Compare the analyzer reading with the gauge to find out if the sender is lying
    5. 5Replace the sender if the gauge shows good pressure, otherwise investigate the engine before running it
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 4314Wrong engine selected - ECM detected

    The engine control module reports an engine type that does not match the engine selected in the machine settings.· Other
    Check soon

    Causes

    • Wrong engine chosen in the analyzer settings
    • Engine or ECM replaced with a different type

    Checks

    1. 1Compare the engine selection in the analyzer with the engine plate
    2. 2Correct the setting and cycle EMS
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 4322Loss of engine speed sensor

    The controller has lost the engine speed signal altogether, so it cannot confirm the engine is running or hold its speed.· Other
    Check soon

    Causes

    • Speed sensor failed or its wire broken
    • Connector loose or corroded

    Checks

    1. 1Check the sensor wire and plug and measure its signal
    2. 2Replace the sensor if there is no signal
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JLG 4323Speed sensor reading invalid speed

    The engine speed reading is not believable, being over the limit the controller allows.· Real condition
    Check soon

    Causes

    • Electrical noise on the speed pickup wire
    • Wrong flywheel teeth setting in the machine configuration
    • Engine speed pickup fault
    • Poor pickup connector contact

    Checks

    1. 1Compare the analyzer rpm with a hand tachometer at idle and at higher speed
    2. 2Check configuration digit 20 (flywheel teeth) against the engine fitted
    3. 3Inspect the pickup wiring for damage and routing close to noisy cables
    4. 4Check the pickup connector and the gap between pickup and flywheel
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Read the sensor value in the analyzer and compare with the gauge or a known reading
  2. 2Check the real condition first: coolant, oil level and pressure, fuel level
  3. 3Inspect the sensor connector and wiring for damage and moisture
  4. 4Unplug the sensor and see whether the reading goes to an open-circuit value
  5. 5Replace the sensor or repair the harness, then clear the code

Causes

  • Sensor failed, shorted or reading out of range
  • Harness damaged between the sensor and the module
  • Real engine condition: overheating, low oil pressure, low fuel
  • Engine control module message not arriving or in error

Most common here: shorted low (3 of 15)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: The engine warning lamp lights, engine speed is limited or the engine shuts down, and the code names the sensor or message involved.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.