JLG · Platform / ground controls
JLG Fault Code 2‑2
Drive or steer selection fault
What does JLG code 2-2 mean?
The drive or steer inputs are in a state the controller will not accept: joystick moved before the footswitch, steer selected before the footswitch, both steer switches active, or the joystick signal out of range. Urgency: check soon - the machine may derate or limit a function. Check first: release everything, let the footswitch open, then press the footswitch first and select drive after.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Release everything, let the footswitch open, then press the footswitch first and select drive after
Then 4 more checksWhere this code shows
Turn the key on and watch the fault lamp or platform display.
Checks
0 of 5 done
Causes
- Operator moved the drive joystick or steer switch before pressing the footswitch
- Footswitch held closed about 7 seconds with nothing selected
- Drive joystick centre tap voltage outside its window (resistive about 3.08-3.83 V, inductive about 2.18-2.70 V)
- Q-Prox sensor on an inductive joystick reading above about 3.18 V, or joystick not neutral
1 more causeFewer causes
- Steer rocker switches stuck or wiring shorted
How it failed
You'll notice: Drive and steer do not respond from the platform even though the engine runs.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Footswitch, joysticks, steer switches and start sequence
- 2-1Footswitch or keyswitch faultReal conditionCheck soon
- 2-2Drive or steer selection faultOtherCheck soon
- 2-3Boom function selection faultOtherCheck soon
- 2-4Steering digital inputs faultyOtherCheck soon
- 2-7Accelerator input faultyOtherCheck soon
- 0011Footswitch openOtherInformation
- 213Footswitch faultyOtherCheck soon
- 224Function problem - steer left permanently selectedOtherCheck soon
- 225Function problem - steer right permanently selectedOtherCheck soon
Show the other 17 codesHide the other codes
- 227Steer switches faultyReal conditionCheck soon
- 234Function switches faulty - check diagnostics/boomReal conditionCheck soon
- 235Function switches locked - selected before aux powerOtherCheck soon
- 236Function switches locked - selected before start switchOtherCheck soon
- 237Start switch locked - selected before keyswitchOtherCheck soon
- 2211Footswitch interlock trippedReal conditionCheck soon
- 2212Drive locked - joystick moved before footswitchOtherCheck soon
- 2213Steer locked - selected before footswitchOtherCheck soon
- 2216Drive/steer joystick out of range highShorted highCheck soon
- 2217Drive/steer joystick centre tap badOtherCheck soon
- 2219Lift/swing joystick out of range highOtherCheck soon
- 2220Lift/swing joystick centre tap badOtherCheck soon
- 2221Lift/swing locked - joystick moved before footswitchOtherCheck soon
- 2222Waiting for footswitch to be openOtherInformation
- 2223Function switches locked - selected before enableOtherCheck soon
- 2224Footswitch selected before startOtherCheck soon
- 2310Function problem - ground enable permanently selectedOtherCheck soon
Other JLG codes: Platform / ground controls
Related on Equipments Finder
Source
JLG 600S/600SJ/660SJ/600A/AJ Service and Maintenance Manual 3120840, section 6 (Tables 6-3, 6-5)
This source lists 2-2 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JLG boom lifts with the JLG Control System (600S, 600SJ, 660SJ, 600A/AJ, 450A, 510A, 400S, 1200/1350SJP families).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
