JCB · Aftertreatment ECU - SCR / DEF
JCB Fault Code P207F‑00
DEF quality error
What does JCB code P207F-00 mean?
The aftertreatment system reports poor DEF quality, usually found after a refill. The system may keep the warning on and later restrict engine power if the fluid is not corrected. Urgency: check soon - the machine may derate or limit a function. Check first: sample the DEF and check it with a refractometer for the correct concentration.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Sample the DEF and check it with a refractometer for the correct concentration
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- Diluted DEF or water added to the tank
- Wrong fluid, such as plain water or contaminated fluid, in the DEF tank
- Old DEF that has degraded after long storage or heat
- Quality sensor faulty or its wiring damaged
1 more causeFewer causes
- DEF contaminated by dirt from a dirty funnel or container
How it failed
You'll notice: The aftertreatment system warns that DEF quality is poor, usually after a refill.
Real conditionRead from how the source describes the code
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DEF quality, quality sensor temperature and SCR efficiency
5 other codes on this part are also real condition (P3402-87, P3403-87, P3405-87, P3406-87 and more). When they show together, start at the wiring and connector they share.
- P207F-00DEF quality errorReal conditionCheck soon
- P207F-86DEF concentration message error from head unit (invalid signal)Lost messageCheck soon
- P207F-87DEF quality message error from head unitLost messageCheck soon
- P2000-00SCR conversion efficiency below thresholdOtherCheck soon
- P2000-02SCR conversion efficiency below thresholdErratic or implausibleCheck soon
- P2000-04SCR conversion efficiency below threshold (system internal failure)Erratic or implausibleCheck soon
- P2000-06SCR conversion efficiency below thresholdErratic or implausibleCheck soon
- P3401-87Excessive SCR catalyst DEF temperature errorOtherCheck soon
- P3402-87DEF concentration too highReal conditionCheck soon
Show the other 10 codesHide the other codes
- P3403-87DEF concentration too lowReal conditionCheck soon
- P3404-87Excessive DEF temperature in SCR systemOtherCheck soon
- P3405-87DEF temperature too high for SCR catalystReal conditionCheck soon
- P3406-87DEF temperature too low for SCR catalystReal conditionCheck soon
- P3407-87DEF temperature sensor open circuitOpen circuitCheck soon
- P3408-87SCR DEF temperature sensor short circuitShort circuitCheck soon
- P3409-87Excessive ambient or operating level error for DEF propertiesOtherCheck soon
- P3410-87DEF level too highReal conditionCheck soon
- P3424SCR partially blocked (overloaded)Erratic or implausibleCheck soon
- P3425SCR fully blocked (plugged)Erratic or implausibleCheck soon
Other JCB codes: Aftertreatment ECU - SCR / DEF
- P204FDEF repeat-offence inducement active
- P2BAA-00Consumption warning requested
- P2BAA-F0Consumption level 2 requested
- P2BAB-00EGR warning requested
- P2BAB-F0EGR level 2 requested, forced idle
- P2BAD-00Inducement override active
- P2BAE-00Driver warning for system tampering
- P2BAE-F0System tampering level 2 requested
Related on Equipments Finder
Source
Partao JCB fault code list, page 11 (code table)
This source lists P207F-00 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Tier 4 Final / Stage V machines with SCR.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
