JCB · Hydraulic controller (HECU)
JCB Function and attachment solenoids fault codes
These solenoids control relief pressure, boom priority, quick hitch, auxiliary and ISO control patterns, the arm limiter, the hammer speed and regeneration load assist. Each one switches a single hydraulic function on the excavator or loader.
Where this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
What do these codes mean?
JCB codes C030A to C1357 are all about the function and attachment solenoids. The most common failure type is short circuit (10 of 20); none needs an immediate stop. Start with this check: identify the function named in the code and find its valve on the block before measuring anything.
How urgent are they?
None of the 20 codes here means stop now; 18 can wait until the shift ends, but find the cause before the next one; 2 are information only.
- Check soon18
- Info2
What should I check first?
Identify the function named in the code and find its valve on the block before measuring anything
Shared checks20 of 20
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
JCB C030AQuick hitch lamp short circuit
The quick hitch lamp circuit is shorted. This is an indicator only: the hitch itself still works, but the lamp in the cab cannot show the hitch state.· Short circuitShort circuitInfoCauses
- Quick hitch lamp bulb or LED shorted
- Lamp wire touching ground
Checks
- 1Check the lamp and its wire for a short
- 2Replace the lamp and recheck
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C030BQuick hitch boom warning lamp open circuit
The quick hitch boom warning lamp circuit is open, so the lamp that warns about the hitch and boom position cannot light. The hitch function itself is not affected.· Open circuitOpen circuitInfoCauses
- Lamp burnt out or its plug loose
- Open lamp wire
Checks
- 1Check the lamp bulb and its feed
- 2Check the lamp wire for continuity
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C130FBoom priority solenoid short circuit
The controller found the boom priority solenoid output shorted, which switches it off to protect the driver. The boom priority solenoid gives the boom priority over other functions, so the boom does not get priority when combined movements are made.· Short circuitShort circuitCheck soonCauses
- Boom priority solenoid coil shorted internally
- Wire to the boom priority solenoid chafed against the frame
Checks
- 1Measure the boom priority solenoid coil resistance against the manual value
- 2Combine boom and another movement and note whether the boom keeps its speed
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C0308Quick hitch solenoid short circuit
The controller found the quick hitch solenoid output shorted, which switches it off to protect the driver. The quick hitch solenoid locks and releases the quick hitch, so the quick hitch will not lock or release from the cab, so attachment changes are blocked.· Short circuitShort circuitCheck soonCauses
- Quick hitch solenoid coil shorted internally
- Wire to the quick hitch solenoid chafed against the frame
Checks
- 1Measure the quick hitch solenoid coil resistance against the manual value
- 2Operate the quick hitch switch and listen for the solenoid click at the valve
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C0309Quick hitch solenoid open circuit
The controller finds no current path in the quick hitch solenoid circuit, an open circuit. The quick hitch solenoid locks and releases the quick hitch, so the quick hitch will not lock or release from the cab, so attachment changes are blocked.· Open circuitOpen circuitCheck soonCauses
- Quick hitch solenoid coil open or the wire to it broken
- Loose or corroded pin at the quick hitch solenoid plug
Checks
- 1Check continuity of the quick hitch solenoid coil and its wires
- 2Operate the quick hitch switch and listen for the solenoid click at the valve
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C0314Auxiliary mode changeover solenoid short circuit
The controller found the auxiliary mode changeover solenoid output shorted, which switches it off to protect the driver. The auxiliary mode changeover solenoid switches the auxiliary circuit between its modes, so the auxiliary circuit stays in one mode, so a double-acting attachment may only work one way.· Short circuitShort circuitCheck soonCauses
- Auxiliary mode changeover solenoid coil shorted internally
- Wire to the auxiliary mode changeover solenoid chafed against the frame
Checks
- 1Measure the auxiliary mode changeover solenoid coil resistance against the manual value
- 2Test the auxiliary mode switch and check the spool changes
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C0315Auxiliary mode changeover solenoid open circuit
The controller finds no current path in the auxiliary mode changeover solenoid circuit, an open circuit. The auxiliary mode changeover solenoid switches the auxiliary circuit between its modes, so the auxiliary circuit stays in one mode, so a double-acting attachment may only work one way.· Open circuitOpen circuitCheck soonCauses
- Auxiliary mode changeover solenoid coil open or the wire to it broken
- Loose or corroded pin at the auxiliary mode changeover solenoid plug
Checks
- 1Check continuity of the auxiliary mode changeover solenoid coil and its wires
- 2Test the auxiliary mode switch and check the spool changes
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C0316ISO controls changeover output short circuit
The controller found the ISO controls changeover output output shorted, which switches it off to protect the driver. The ISO controls changeover output changes the joystick pattern between the available control layouts, so the joystick pattern cannot be changed and may be stuck in the wrong layout.· Short circuitShort circuitCheck soonCauses
- Iso controls changeover output coil shorted internally
- Wire to the ISO controls changeover output chafed against the frame
Checks
- 1Measure the ISO controls changeover output coil resistance against the manual value
- 2Switch the pattern selector and see whether the output toggles on live data
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C0317ISO controls changeover output open circuit
The controller finds no current path in the ISO controls changeover output circuit, an open circuit. The ISO controls changeover output changes the joystick pattern between the available control layouts, so the joystick pattern cannot be changed and may be stuck in the wrong layout.· Open circuitOpen circuitCheck soonCauses
- Iso controls changeover output coil open or the wire to it broken
- Loose or corroded pin at the ISO controls changeover output plug
Checks
- 1Check continuity of the ISO controls changeover output coil and its wires
- 2Switch the pattern selector and see whether the output toggles on live data
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C0318Arm limiter solenoid output short circuit
The controller found the arm limiter solenoid output shorted, which switches it off to protect the driver. The arm limiter solenoid limits arm movement near the cab, so the arm limiter does not engage, so the arm may reach positions that are normally prevented.· Short circuitShort circuitCheck soonCauses
- Arm limiter solenoid coil shorted internally
- Wire to the arm limiter solenoid chafed against the frame
Checks
- 1Measure the arm limiter solenoid coil resistance against the manual value
- 2Check the limiter on the machine and the solenoid plug
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C0319Arm limiter solenoid open circuit
The controller finds no current path in the arm limiter solenoid circuit, an open circuit. The arm limiter solenoid limits arm movement near the cab, so the arm limiter does not engage, so the arm may reach positions that are normally prevented.· Open circuitOpen circuitCheck soonCauses
- Arm limiter solenoid coil open or the wire to it broken
- Loose or corroded pin at the arm limiter solenoid plug
Checks
- 1Check continuity of the arm limiter solenoid coil and its wires
- 2Check the limiter on the machine and the solenoid plug
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C0326Hammer speed regulator solenoid short circuit
The controller found the hammer speed regulator solenoid output shorted, which switches it off to protect the driver. The hammer speed regulator solenoid sets the hammer attachment speed, so the hammer runs at the wrong speed or flow.· Short circuitShort circuitCheck soonCauses
- Hammer speed regulator solenoid coil shorted internally
- Wire to the hammer speed regulator solenoid chafed against the frame
Checks
- 1Measure the hammer speed regulator solenoid coil resistance against the manual value
- 2Run the hammer function and compare the commanded and measured current
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C0327Hammer speed regulator solenoid open circuit
The controller finds no current path in the hammer speed regulator solenoid circuit, an open circuit. The hammer speed regulator solenoid sets the hammer attachment speed, so the hammer runs at the wrong speed or flow.· Open circuitOpen circuitCheck soonCauses
- Hammer speed regulator solenoid coil open or the wire to it broken
- Loose or corroded pin at the hammer speed regulator solenoid plug
Checks
- 1Check continuity of the hammer speed regulator solenoid coil and its wires
- 2Run the hammer function and compare the commanded and measured current
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C1300Short circuit in 2-stage MRV solenoid circuit
The controller found the 2-stage MRV solenoid output shorted, which switches it off to protect the driver. The 2-stage MRV solenoid switches the main relief valve between its two pressure stages, so the main relief stays at one pressure stage, so work power may be low.· Short circuitShort circuitCheck soonCauses
- 2-stage mrv solenoid coil shorted internally
- Wire to the 2-stage MRV solenoid chafed against the frame
Checks
- 1Measure the 2-stage MRV solenoid coil resistance against the manual value
- 2Monitor main pressure while commanding both stages
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C13012-stage MRV solenoid open circuit
The controller finds no current path in the 2-stage MRV solenoid circuit, an open circuit. The 2-stage MRV solenoid switches the main relief valve between its two pressure stages, so the main relief stays at one pressure stage, so work power may be low.· Open circuitOpen circuitCheck soonCauses
- 2-stage mrv solenoid coil open or the wire to it broken
- Loose or corroded pin at the 2-stage MRV solenoid plug
Checks
- 1Check continuity of the 2-stage MRV solenoid coil and its wires
- 2Monitor main pressure while commanding both stages
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C1305Max flow control solenoid short circuit
The controller found the max flow control solenoid output shorted, which switches it off to protect the driver. The max flow control solenoid limits maximum pump flow, so maximum flow cannot be controlled so some functions move too fast or too slowly.· Short circuitShort circuitCheck soonCauses
- Max flow control solenoid coil shorted internally
- Wire to the max flow control solenoid chafed against the frame
Checks
- 1Measure the max flow control solenoid coil resistance against the manual value
- 2Command the max flow control and watch the flow value
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C1306Max flow control solenoid open circuit
The controller finds no current path in the max flow control solenoid circuit, an open circuit. The max flow control solenoid limits maximum pump flow, so maximum flow cannot be controlled so some functions move too fast or too slowly.· Open circuitOpen circuitCheck soonCauses
- Max flow control solenoid coil open or the wire to it broken
- Loose or corroded pin at the max flow control solenoid plug
Checks
- 1Check continuity of the max flow control solenoid coil and its wires
- 2Command the max flow control and watch the flow value
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C1310Boom priority solenoid open circuit
The controller finds no current path in the boom priority solenoid circuit, an open circuit. The boom priority solenoid gives the boom priority over other functions, so the boom does not get priority when combined movements are made.· Open circuitOpen circuitCheck soonCauses
- Boom priority solenoid coil open or the wire to it broken
- Loose or corroded pin at the boom priority solenoid plug
Checks
- 1Check continuity of the boom priority solenoid coil and its wires
- 2Combine boom and another movement and note whether the boom keeps its speed
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB C1356Regen load assist solenoid short circuit
The controller found the regeneration load assist solenoid output shorted, which switches it off to protect the driver. The regeneration load assist solenoid assists the regeneration circuit under load, so regeneration load assist is off, so some digging movements may feel slower.· Short circuitShort circuitCheck soonCauses
- Regeneration load assist solenoid coil shorted internally
- Wire to the regeneration load assist solenoid chafed against the frame
Checks
- 1Measure the regeneration load assist solenoid coil resistance against the manual value
- 2Check the solenoid current when the function is commanded
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB C1357Regen load assist solenoid open circuit
The controller finds no current path in the regeneration load assist solenoid circuit, an open circuit. The regeneration load assist solenoid assists the regeneration circuit under load, so regeneration load assist is off, so some digging movements may feel slower.· Open circuitOpen circuitCheck soonCauses
- Regeneration load assist solenoid coil open or the wire to it broken
- Loose or corroded pin at the regeneration load assist solenoid plug
Checks
- 1Check continuity of the regeneration load assist solenoid coil and its wires
- 2Check the solenoid current when the function is commanded
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Shared checks
Checks, in order
- 1Identify the function named in the code and find its valve on the block before measuring anything
- 2Measure that valve coil resistance and compare it with a similar coil on the same block
- 3Check the quick hitch and boom warning lamp bulbs when a lamp output is named
- 4Run the output test for that function and confirm the valve clicks and the attachment moves
Causes
- Valve coil failed on the named function
- Harness chafed where the boom or arm hoses flex
- Lamp or indicator output open on a quick hitch warning
- Connector at the valve block full of water or oil
Most common here: short circuit (10 of 20)
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
When to stop
You'll notice: A single function or attachment may not work, for example the quick hitch will not release or the hammer runs at the wrong speed.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Partao JCB fault code list, page 1 (code table)
- Partao JCB fault code list, page 2 (code table)
- Partao JCB fault code list, page 4 (code table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
