EF Logo

JCB · Engine ECU (Dieselmax / Ecomax) - temperature sensors

JCB Fuel, oil and coolant temperature sensors and engine overheating fault codes

The fuel temperature sensor and the engine oil temperature sensor are thermistors that tell the ECU how hot the diesel and the oil are. The ECU uses them to correct fuel quantity and protect the engine and pump.

More about these parts

The coolant temperature sensor is a thermistor in the engine coolant that tells the ECU how hot the engine is. The ECU uses it for starting, fan control, fuel quantity and overheating protection. These codes and alarms report coolant that is too hot or too low for safe running. They come from the machine and engine controllers and warn the operator before engine damage.

FaultCheckP0117JCB · Fuel, oil and coolant temperature sensors and engine overheating
Code shows hereFAULTP0117

Where this code shows

Switch the key on and note any warning lamp or fault icon on the cluster.

What do these codes mean?

JCB codes P0115 to B1546 are all about the fuel, oil and coolant temperature sensors and engine overheating. The most common failure type is lost message (4 of 18); 2 need an immediate stop. Start with this check: compare the reading with coolant temperature on a cold engine, the three should be close.

How urgent are they?

2 of 18 codes here mean stop now; the other 16 can wait until the shift ends, but find the cause before the next one.

  • Stop now2
  • Check soon16

What should I check first?

Compare the reading with coolant temperature on a cold engine, the three should be close

Shared checks

18 of 18

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JCB P0115Coolant temperature sensor 1 circuit fault

    The ECU sees the engine coolant temperature sensor signal out of range or missing.· Other
    Check soon

    Causes

    • Coolant temperature sensor failed or its resistance drifting
    • Damaged harness or loose connector at the sensor
    • Coolant level low so the sensor is not covered
    • Corrosion at the sensor pins affecting the signal
    • Poor ECU ground adding error to the reading

    Checks

    1. 1Read the coolant temperature live and compare it with a gauge or infrared thermometer on the sensor body
    2. 2Check the coolant level and that the sensor is in the liquid
    3. 3Inspect the sensor connector for corrosion and spread pins
    4. 4Check the signal wire for chafing and for continuity back to the ECU
    5. 5Measure the sensor resistance cold and warm and check it changes smoothly
    6. 6Check the ECU ground and the 5 V reference for other sensor faults
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0116Coolant temperature sensor range/performance

    Coolant temperature sensor range/performance.· Erratic or implausible
    Check soon

    Causes

    • Coolant temperature sensor range/performance drifting or worn so it no longer matches the real condition
    • Poor connection or high resistance in the coolant temperature sensor range/performance circuit
    • A related fault elsewhere making this reading look wrong

    Checks

    1. 1Compare the coolant temperature sensor range/performance value on live data with a known good value or a reference gauge
    2. 2Check the coolant temperature sensor range/performance connector and wiring for high resistance and intermittent contact
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P0117Coolant temperature sensor signal low

    The voltage from the coolant sensor is too low, which reads as an impossibly hot engine, usually a short to ground.· Shorted low
    Check soon

    Causes

    • Signal wire shorted to ground
    • Coolant temperature sensor shorted internally
    • Water in the connector bridging the signal pin to ground
    • Harness rubbed through against the engine or a bracket
    • Damaged ECU input, which is rare

    Checks

    1. 1With key on, read the live temperature and check it reads an impossibly high value
    2. 2Unplug the sensor and see whether the reading swings to the opposite extreme
    3. 3Check the signal wire for a short to ground with the connector unplugged
    4. 4Inspect the sensor plug near the thermostat housing for water or corrosion
    5. 5Look along the harness for rub marks against the block or brackets
    6. 6Measure the sensor resistance and see whether it is close to zero ohms
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P0118Coolant temperature sensor signal high

    The voltage from the coolant sensor is too high, which reads as an extremely cold engine, usually an open circuit.· Open circuit
    Check soon

    Causes

    • Open circuit in the coolant sensor wiring near the thermostat housing
    • Coolant sensor unplugged, or its pins corroded by coolant seepage
    • Signal wire shorted to the 5 V reference or to supply
    • Coolant temperature sensor failed open
    • Wire broken at the plug from engine vibration

    Checks

    1. 1Read the live coolant temperature with the engine warm and confirm it is stuck at a very low value
    2. 2Check the plug is fully seated and look at the pins for green coolant corrosion
    3. 3Check the signal wire for continuity from the sensor plug to the ECU
    4. 4Check the signal wire for a short to supply with the sensor unplugged
    5. 5Measure the sensor resistance and see if it reads open
    6. 6Jumper the two sensor pins together and watch the reading swing to maximum
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0180Fuel temperature sensor A circuit fault

    The engine ECU flagged a fault on the fuel temperature sensor A circuit without saying whether the signal is low, high or erratic.· Erratic or implausible
    Check soon

    Causes

    • Fuel temperature sensor A open internally or damaged where it screws into the fuel path
    • Terminal fretting or moisture at the sensor plug that makes the reading come and go
    • Harness damage between the sensor and the engine ECU

    Checks

    1. 1With the engine cold, read the fuel temperature on live data and compare it with ambient and coolant temperature; a cold engine should read close to all of them
    2. 2Unplug sensor A and measure its resistance, then warm the sensor in your hand and confirm the value moves smoothly
    3. 3Wiggle the harness while watching the reading to separate a broken wire from a failed thermistor
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P0181Fuel temperature sensor fault

    The fuel temperature reading is present but does not make sense against the other engine temperatures, for example it stays fixed while the engine warms up.· Erratic or implausible
    Check soon

    Causes

    • Fuel temperature sensor is stuck or slow to respond
    • Corroded plug adding resistance, so the reading is offset but not out of range
    • Sensor fitted in a poor position after fuel system work and reading ambient air rather than fuel

    Checks

    1. 1Compare fuel temperature with coolant temperature after a cold soak; the two should start together and the fuel value should then climb steadily
    2. 2Run the engine to working temperature and watch whether the fuel value rises at all or stays frozen
    3. 3Replace the sensor only after the plug pins have been cleaned and the harness checked, since offset readings are often connector resistance
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P0181-87Missing fuel temperature CAN message

    The fuel temperature value is passed to this controller as a CAN message and that message stopped arriving.· Lost message
    Check soon

    Causes

    • Engine ECU not sending the fuel temperature frame, for example during a reset or low supply voltage
    • CAN high or low wire open or chafed between the engine ECU and the receiving controller

    Checks

    1. 1Read the engine ECU's own fault list; if it reports no fuel temperature fault, the problem is the bus and not the sensor
    2. 2Check battery voltage during cranking and the CAN wiring and termination before touching the sensor
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P0182Fuel temperature sensor A signal low

    The fuel temperature sensor A signal sits below its allowed range, which the ECU reads as an impossibly cold fuel.· Other
    Check soon

    Causes

    • Fuel temperature signal wire chafed against the engine block or a bracket
    • Sensor thermistor shorted internally
    • Water inside the sensor plug creating a leak path to ground

    Checks

    1. 1Unplug sensor A; if the live value jumps to the open-circuit default, the sensor is the short, if it stays low the wire is grounded
    2. 2Measure the signal wire to ground with the plug removed and the key off; it should not read a short
    3. 3Inspect the harness run where it passes brackets and the fuel rail for rubbed insulation
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0183Fuel temperature sensor A signal high

    The fuel temperature sensor A signal sits above its allowed range, which the ECU reads as extremely hot or disconnected fuel.· Shorted high
    Check soon

    Causes

    • Open circuit in the fuel temperature signal wire
    • Sensor plug not fully latched or pins pushed back
    • Signal wire shorted to a supply, for example a chafed lead against another live wire

    Checks

    1. 1With key on, check for the sensor reference voltage at the plug and for the ground return
    2. 2Bridge the two sensor pins with a short jumper and see whether the reading drops to a very low value; if it does, the wiring to the ECU is fine and the sensor is open
    3. 3Check continuity from the sensor plug to the ECU pin for each of the two wires
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P0195Oil temperature sensor external voltage fault

    The ECU found the engine oil temperature sensor outside its expected voltage window on the external supply side.· Other
    Check soon

    Causes

    • Wrong voltage reaching the oil temperature sensor from the ECU supply
    • Sensor plug or ECU pin corroded, adding resistance in the feed
    • Another sensor on the same circuit pulling the voltage down

    Checks

    1. 1Measure the voltage at the oil temperature sensor plug with the key on and compare it with the other sensors on the same feed
    2. 2Unplug other sensors one at a time on the shared feed to see whether the voltage recovers
    3. 3Look for water or oil inside the sensor plug
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0196Oil temperature sensor signal gradient fault

    The oil temperature signal is changing faster than oil in a running engine can heat or cool, so the ECU treats it as unreliable.· Lost message
    Check soon

    Causes

    • Loose pin in the oil temperature sensor plug making the value jump
    • Cracked sensor body or internal break that opens and closes with vibration
    • Chafed signal wire that touches ground only when the engine shakes

    Checks

    1. 1Record the oil temperature on live data while the engine runs and look for steps or spikes of many degrees in a second
    2. 2Tap and flex the harness near the sensor while watching the reading
    3. 3Measure the sensor resistance at two different temperatures and confirm it changes smoothly with no jumps
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P0196-87Missing oil temperature CAN message from engine ECU

    The oil temperature value is sent by the engine ECU over CAN and the message did not arrive.· Lost message
    Check soon

    Causes

    • Engine ECU not transmitting the oil temperature frame
    • CAN wiring or connector fault between the engine ECU and the controller reporting the fault

    Checks

    1. 1See whether the engine ECU shows its own oil temperature fault; if not, the bus is the suspect
    2. 2Check CAN high and low continuity and the terminating resistance, then repeat the read with the engine running
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P0197Oil temperature sensor signal low

    The oil temperature signal is below range, so the ECU thinks the oil is far colder than possible.· Other
    Check soon

    Causes

    • Oil temperature signal wire shorted to ground
    • Sensor internally shorted
    • Water or oil wicked into the plug creating a leak to ground

    Checks

    1. 1Unplug the oil temperature sensor and watch the live value; if it jumps to the open default the sensor is the short
    2. 2Measure the signal wire to ground with the key off and the plug removed
    3. 3Check the engine harness where it crosses the block for chafing
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0198Oil temperature sensor signal high

    The oil temperature signal is above range, so the ECU thinks the oil is extremely hot or the sensor is not connected.· Shorted high
    Check soon

    Causes

    • Open circuit in the oil temperature signal or return wire
    • Sensor unplugged or its terminal pushed back out of position
    • Signal wire shorted to a supply wire

    Checks

    1. 1Compare the reading with the coolant temperature; if coolant is normal and oil reads at maximum, suspect the sensor circuit
    2. 2Bridge the sensor plug pins with a jumper and see whether the reading falls; that proves the wiring to the ECU is intact
    3. 3Check the sensor connector for a pushed-back pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P0217Coolant temperature above limit (overheating)

    Engine coolant temperature has gone above the maximum limit set in the ECU.· Shorted high
    Stop now

    Causes

    • Coolant level low from a leak, or air trapped in the system after a repair
    • Radiator core or charge cooler blocked with dirt, chaff or oil on the outside
    • Fan not running, belt slipping or the hydraulic fan drive not responding
    • Thermostat stuck closed or water pump worn
    • Coolant sensor wrong, so overheating is partly a false reading

    Checks

    1. 1Let the engine cool, then check the coolant level and look for leaks, damp hoses and oil in the coolant
    2. 2Clean the radiator and cooler fins, looking through them for light
    3. 3Check fan speed and belt tension, and the fan solenoid if the machine has a variable fan
    4. 4Check the thermostat opens by feeling hoses warm up in sequence
    5. 5Compare the ECU temperature with an infrared reading on the sensor housing
    6. 6Check the pressure cap holds pressure and the overflow reservoir is not empty
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB C1021Engine coolant level low

    The machine controller sees a low engine coolant level from the level switch or sender.· Other
    Check soon

    Causes

    • Coolant level genuinely low from a hose, radiator or water pump leak
    • Air pocket in the cooling system after a recent drain or repair
    • Coolant level sender or switch failed or covered in scale
    • Wiring fault or loose connector at the level sender
    • Overflow bottle cap or pressure cap not sealing and letting coolant out

    Checks

    1. 1With the engine cold, check the coolant level in the radiator and in the expansion tank
    2. 2Look for wet hoses, drips under the engine and white residue at joints
    3. 3Check the level sender and its connector for corrosion
    4. 4Check the sender wiring for continuity back to the controller
    5. 5Bleed air from the system and recheck the level after running
    6. 6Check the cap seals and pressure rating, and replace it if it is worn
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB B1543Critical high coolant temperature

    Coolant temperature has reached the critical level.· Lost message
    Stop now

    Causes

    • Low coolant level or a leak
    • Radiator or cooler blocked, or the fan not running
    • Thermostat stuck closed or water pump failing
    • Head gasket leak letting exhaust gas into the coolant
    • Faulty coolant sensor giving a false high reading

    Checks

    1. 1Shut the engine down and let it cool before opening the cap
    2. 2Check the coolant level once cool and look for leaks around hoses
    3. 3Clean the radiator and check the fan and belt
    4. 4Check the thermostat and hoses for temperature differences
    5. 5Look for bubbles or oil in the coolant that point to a head gasket leak
    6. 6Compare the display temperature with an infrared reading at the sensor
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB B1546Coolant temperature high (operator level)

    Coolant temperature is high enough to show an operator warning, but is not yet critical.· Other
    Check soon

    Causes

    • Radiator fins blocked with dirt or chaff
    • Coolant level low
    • Fan drive or belt not working properly

    Checks

    1. 1Reduce the load and let the engine idle so the temperature falls
    2. 2Clean the radiator fins and check the airflow through the core
    3. 3Check the coolant level once the engine has cooled down
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Compare the reading with coolant temperature on a cold engine, the three should be close
  2. 2Compare the sensor reading with an infrared reading on the housing when the engine is cold and warm
  3. 3Stop and let the engine cool before opening the cap, then check the coolant level and look for leaks
  4. 4Measure the sensor resistance and compare it with the manual curve at a known temperature
  5. 5Measure the sensor resistance and compare it with the manual curve
  6. 6Clean the radiator and cooler fins and check the fan, belt and fan solenoid
  7. 7Check the signal wire for a short to ground or to the 5 V supply

Causes

  • Sensor thermistor failed or drifting
  • Low coolant level or a leak
  • Corroded connector or loose pin
  • Corroded or loose connector

Most common here: lost message (4 of 18)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: The engine usually keeps running with a check lamp on, and the ECU may use a default temperature that reduces power on a hot day.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.