J1939 · Engine speed/timing
SPN 636 Fault Code
Engine position sensor
What does SPN 636 mean?
The sensor that reports crank or cam position to the ECM so it can time injection. Lists from different engine makers label SPN 636 as the camshaft or the crankshaft position input. How urgent it is depends on the FMI after SPN 636 - pick it below. Check first: check the crank signal while cranking in the service tool; the speed should show a steady value.
- SPN 636
- Engine position sensor
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 636 - pick it below.
What should I check first?
Check the crank signal while cranking in the service tool; the speed should show a steady value
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 636?
You'll notice: The crank position signal is lost, wrong or out of step with the cam signal, so the engine may crank without starting, run rough or stall.
Find the number shown after SPN 636 on your display. FMI 2 has its own page with causes and checks.
- 1SPN 636 FMI 1: Position sensor signal voltage is too lowReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 2SPN 636 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleMack MP8, Mack MP7, Volvo D13
- 3SPN 636 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 3 more
- 4SPN 636 FMI 4: Position sensor signal is shorted to groundShorted lowDetroit DD15
- 8SPN 636 FMI 8: Abnormal frequency, pulse width or period of the signalErratic or implausibleMack MP8, Mack MP7, Volvo D13
- 10SPN 636 FMI 10: Position sensor signal is erraticErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 11SPN 636 FMI 11: Position sensor has failedOtherDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 15SPN 636 FMI 15: The camshaft and crankshaft signals do not match each otherReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 31SPN 636 FMI 31: An error was detected on the position sensor signalReal conditionDetroit DD15
Checks
0 of 5 done
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
How urgent SPN 636 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Sensor circuit fault: wiring open, shorted or chafed at the crank sensor plug on the flywheel housing
- Sensor gap wrong, or the sensor loose, dirty or damaged
- Tone wheel on the crank damaged or loose, so the signal has missing or extra teeth
- Cam sensor or timing gear fault that upsets the crank-to-cam relationship
Other Engine speed/timing codes
Source
Detroit Diesel DD15 2017-2020 fault codes list (Diesel Laptops)
This list names SPN 636 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Detroit DD13 and DD15 (2017-2020); same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
