EF Logo

J1939 · Turbo

SPN 103 Fault Code

Engine turbocharger 1 speed

What does SPN 103 mean?

Rotational speed of the turbocharger shaft, from a speed sensor on the turbo housing. The ECM uses it to protect the turbo from overspeed and to control boost. How urgent it is depends on the FMI after SPN 103 - pick it below. Check first: compare the turbo speed reading with boost pressure under load; they should rise together.

FaultActiveSPN 103FMI --J1939 engine ECU
SPN 103
Engine turbocharger 1 speed
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 103 - pick it below.

What should I check first?

Compare the turbo speed reading with boost pressure under load; they should rise together

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 103?

You'll notice: The turbo speed signal is wrong, so the ECM cannot protect the turbo from over-speeding.

Find the number shown after SPN 103 on your display.

  • 0SPN 103 FMI 0: Value is above the normal range, most severe levelReal conditionCummins ISX15, Mack MP8, Mack MP7, Volvo D13
  • 1SPN 103 FMI 1: Value is below the normal range, most severe levelReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 3 more
  • 2SPN 103 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 2 more
  • 3SPN 103 FMI 3: Turbo speed signal is high or shorted to supply, or reads too highShorted highPACCAR MX-13
  • 4SPN 103 FMI 4: Turbo speed signal is low or shorted to ground, or reads too lowShorted lowDetroit DD15, Detroit DD13, PACCAR MX-13
  • 9SPN 103 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageMack MP8, Mack MP7, Volvo D13
  • 10SPN 103 FMI 10: The value is changing at an abnormal rateErratic or implausiblePACCAR MX-13
  • 15SPN 103 FMI 15: Value is above the normal range, least severe levelReal conditionCummins ISX15, Mack MP8, Mack MP7, Volvo D13
  • 16SPN 103 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15
  • 17SPN 103 FMI 17: Value is below the normal range, least severe levelReal conditionMack MP8, Mack MP7, Volvo D13
  • 18SPN 103 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15

Checks

0 of 5 done

When to stop

Make the machine safe before you start: on firm level ground, attachments down, key out.

How urgent SPN 103 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Speed sensor circuit fault: open, short or damaged wiring from the turbo speed sensor to the ECM
  • Sensor gap or damaged sensor tip at the turbo housing
  • Turbo itself failing: worn bearings or damaged compressor wheel giving a true low or erratic speed
  • Oil or heat damage to the sensor connector at the turbo

Source

Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)

This list names SPN 103 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.