Hyundai · Transmission TCU codes (hex)
Hyundai TCU temperature and speed sensor inputs fault codes
The TCU reads transmission sump temperature, retarder temperature and four speed signals: engine, turbine, internal and output. A short or open on one of these inputs, or a logical mismatch between speeds, produces a code.
Where this code shows
Turn the key on and open the fault code or diagnosis menu on the cluster.
What do these codes mean?
Hyundai codes 3A to 39 are all about the tCU temperature and speed sensor inputs. The most common failure type is shorted high (6 of 17); none needs an immediate stop. Start with this check: check the sensor cable and connectors from the TCU to the transmission for chafing and corrosion.
How urgent are they?
None of the 17 codes here means stop now; 13 can wait until the shift ends, but find the cause before the next one; 4 are information only.
- Check soon13
- Info4
What should I check first?
Check the sensor cable and connectors from the TCU to the transmission for chafing and corrosion
Shared checks17 of 17
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Hyundai 3ATCU output speed input: short to battery voltage or open circuit
The output speed input voltage is too high, so the TCU loses the signal (output speed is the shaft speed that the TCU uses for gear selection and vehicle speed). Without output speed the TCU cannot pick gears from vehicle speed and uses a special gear selection mode, so automatic shifting may feel wrong. A signal should appear on the output speed input as soon as the machine rolls, and none means the wire is open. Check the output pickup tip and its seal.· Shorted highShorted highCheck soonCauses
- Output speed sensor cable shorted to battery voltage or open
- Output speed sensor failed
Checks
- 1Check the output speed sensor cable and connector
- 2Check the output speed sensor gap and condition
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 3BTCU output speed input: short to ground
The output speed input voltage is too low, so the TCU loses the signal (output speed is the shaft speed that the TCU uses for gear selection and vehicle speed). A grounded output speed line reads under the 1.00 V limit in the manual, and the TCU moves to its special gear selection mode. A flat low reading on the output speed input with the machine rolling confirms the short to ground.· Shorted lowShorted lowCheck soonCauses
- Output speed sensor cable shorted to ground
- Output speed sensor failed
Checks
- 1Check the output speed sensor cable for a path to ground
- 2Check the output sensor and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 3CTCU logical error at output speed input
The output speed reading is outside what the TCU can accept as plausible; output speed is the shaft speed that the TCU uses for gear selection and vehicle speed. A mismatch on output speed points to noise or a wrong gap at the pickup, and the TCU then uses its special gear selection mode. Compare output speed with the road speed on the cluster; a wild mismatch confirms a noise or gap fault.· Lost messageLost messageCheck soonCauses
- Output speed sensor gap wrong
- Signal interference on the output speed cable
Checks
- 1Check the output sensor gap against the manual
- 2Compare the output speed signal with the other speeds while running
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 3ETCU output speed zero does not fit the other speed signals
The output speed reads zero while other speed signals show motion, so the TCU switches to a special gear selection mode. This code shows when output speed reads zero while turbine and internal speed are moving, which is the classic sign of a dead output pickup or a broken wire. Roll the machine slowly and see whether any output speed value appears on the display.· Open circuitOpen circuitCheck soonCauses
- Output speed sensor failed or gap wrong
- Output speed cable broken
Checks
- 1Check the output speed sensor gap and cable
- 2Compare the output speed with turbine and internal speed while moving
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Hyundai 25TCU transmission sump temperature sensor: short to battery voltage or open circuit
The measured voltage on the sump temperature input is too high, so the TCU keeps running but assumes a default sump temperature. With the sump reading missing the TCU relies on a stored temperature, so any overheat protection that depends on sump temperature is blind until the sensor is repaired. Look at the sump sensor connector on the gearbox for oil seepage along the wire, which can wick into the plug. Compare with a similar machine if available.· Shorted highShorted highInfoCauses
- Cable shorted to battery voltage or open
- Sump temperature sensor failed
Checks
- 1Check the cable and connector from the TCU to the temperature sensor
- 2Check the sump temperature sensor wire for a break or contact with supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 26TCU transmission sump temperature sensor: short to ground
The measured voltage on the sump temperature input is too low, so the TCU keeps running but assumes a default sump temperature. A short to ground at this sensor looks like a very hot sump to the controller, so compare with a real oil temperature before concluding the gearbox is overheating. Look at the sump sensor wire where it passes the gearbox housing for rubbed insulation that could touch metal.· Shorted lowShorted lowInfoCauses
- Cable shorted to vehicle ground
- Sump temperature sensor failed
Checks
- 1Check the cable and connector from the TCU to the temperature sensor
- 2Check the sump temperature sensor wire for chafing to the housing
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 27TCU retarder temperature sensor: short to battery voltage or open circuit
The measured voltage on the retarder temperature input is too high, so the TCU keeps running but assumes a default retarder temperature. The retarder temperature input protects the retarder oil, so with the signal gone the TCU assumes a default value and cannot warn of retarder overheating. Look at the retarder sensor plug for oil or heat damage that can open the circuit. A visual check of the retarder oil level is worthwhile.· Shorted highShorted highInfoCauses
- Retarder temperature cable shorted to battery voltage or open
- Retarder temperature sensor failed
Checks
- 1Check the cable and connector from the TCU to the temperature sensor
- 2Check the retarder temperature sensor wire for a break or contact with supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 28TCU retarder temperature sensor: short to ground
The measured voltage on the retarder temperature input is too low, so the TCU keeps running but assumes a default retarder temperature. A grounded retarder sensor wire looks like extreme retarder heat, so check the real oil temperature before acting on any related warning. Look at where the retarder sensor wire runs close to hot housings for melted insulation touching metal.· Shorted lowShorted lowInfoCauses
- Retarder temperature cable shorted to ground
- Retarder temperature sensor failed
Checks
- 1Check the cable and connector from the TCU to the temperature sensor
- 2Check the retarder temperature sensor wire for chafing to ground
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 31TCU engine speed input: short to battery voltage or open circuit
The engine speed input voltage is too high, so the TCU loses the signal (engine speed is the input side of the converter and the TCU compares it with turbine speed to judge converter slip). Without the engine speed the TCU cannot see converter slip and falls back to substitute clutch control with timed shifts, which feel harsher than normal. On the cluster the engine speed reading from the engine controller can be used to tell whether the engine itself is running normally. Check the pickup gap against the manual.· Shorted highShorted highCheck soonCauses
- Engine speed sensor cable shorted to battery voltage or open
- Engine speed sensor failed
Checks
- 1Check the engine speed sensor cable and connector
- 2Check the engine speed sensor gap and condition
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 32TCU engine speed input: short to ground
The engine speed input voltage is too low, so the TCU loses the signal (engine speed is the input side of the converter and the TCU compares it with turbine speed to judge converter slip). A grounded engine speed line produces a voltage below the 0.45 V limit the manual quotes, which is why the TCU treats the engine speed as missing. A meter on the signal pin with the engine running should show a changing signal, and a flat low reading confirms the short.· Shorted lowShorted lowCheck soonCauses
- Engine speed sensor cable shorted to ground
- Engine speed sensor failed
Checks
- 1Check the engine speed sensor cable for a path to ground
- 2Check the engine sensor and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 33TCU logical error at engine speed input
The engine speed reading is outside what the TCU can accept as plausible; engine speed is the input side of the converter and the TCU compares it with turbine speed to judge converter slip. A mismatch here usually means the engine speed signal has noise or the pickup gap is wrong, so shift quality gets worse under load. Compare the TCU engine speed with the cluster engine speed from the engine controller; they should agree within a few rpm at steady idle.· Lost messageLost messageCheck soonCauses
- Engine speed sensor gap wrong
- Signal interference on the engine speed cable
Checks
- 1Check the engine sensor gap against the manual
- 2Compare the engine speed signal with the other speeds while running
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 34TCU turbine speed input: short to battery voltage or open circuit
The turbine speed input voltage is too high, so the TCU loses the signal (turbine speed is the converter output and tells the TCU how fast the gearbox input is turning). Without turbine speed the TCU loses the converter output reading and falls back to substitute clutch control, which makes shifts less smooth. A speed signal should appear on the turbine input with the engine running and the machine in gear, and nothing there means the wire is open. Check the pickup gap and the pickup tip for damage.· Shorted highShorted highCheck soonCauses
- Turbine speed sensor cable shorted to battery voltage or open
- Turbine speed sensor failed
Checks
- 1Check the turbine speed sensor cable and connector
- 2Check the turbine speed sensor gap and condition
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 35TCU turbine speed input: short to ground
The turbine speed input voltage is too low, so the TCU loses the signal (turbine speed is the converter output and tells the TCU how fast the gearbox input is turning). A grounded turbine line reads under the 0.45 V limit quoted in the manual, which is why the TCU treats turbine speed as missing. A flat low reading on the turbine input with the engine running confirms the short to ground.· Shorted lowShorted lowCheck soonCauses
- Turbine speed sensor cable shorted to ground
- Turbine speed sensor failed
Checks
- 1Check the turbine speed sensor cable for a path to ground
- 2Check the turbine sensor and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 36TCU logical error at turbine speed input
The turbine speed reading is outside what the TCU can accept as plausible; turbine speed is the converter output and tells the TCU how fast the gearbox input is turning. A mismatch on turbine speed usually points to noise or a wrong gap at that pickup, and shifts become rough as the TCU distrusts the reading. Compare turbine speed with engine speed in gear: they should relate according to the converter ratio and a wild mismatch confirms a noise or gap fault.· Lost messageLost messageCheck soonCauses
- Turbine speed sensor gap wrong
- Signal interference on the turbine speed cable
Checks
- 1Check the turbine sensor gap against the manual
- 2Compare the turbine speed signal with the other speeds while running
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 37TCU internal speed input: short to battery voltage or open circuit
The internal speed input voltage is too high, so the TCU loses the signal (internal speed is the gearbox shaft speed the TCU uses to judge clutch slip). Without internal speed the TCU cannot judge clutch slip and falls back to substitute clutch control. A signal should appear on the internal speed input as soon as the transmission rotates in gear. Check the pickup tip for metal debris.· Shorted highShorted highCheck soonCauses
- Internal speed sensor cable shorted to battery voltage or open
- Internal speed sensor failed
Checks
- 1Check the internal speed sensor cable and connector
- 2Check the internal speed sensor gap and condition
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Hyundai 38TCU internal speed input: short to ground
The internal speed input voltage is too low, so the TCU loses the signal (internal speed is the gearbox shaft speed the TCU uses to judge clutch slip). A grounded line on this input reads under the 0.45 V limit in the manual, and the TCU treats internal speed as missing. A flat low reading on the internal speed input with the shaft turning confirms the short to ground.· Shorted lowShorted lowCheck soonCauses
- Internal speed sensor cable shorted to ground
- Internal speed sensor failed
Checks
- 1Check the internal speed sensor cable for a path to ground
- 2Check the internal sensor and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Hyundai 39TCU logical error at internal speed input
The internal speed reading is outside what the TCU can accept as plausible; internal speed is the gearbox shaft speed the TCU uses to judge clutch slip. A mismatch on internal speed points to noise or a wrong gap at that pickup, and shifting may become rough. Compare internal speed with output speed in each gear: the ratio should match the gear and a mismatch confirms a noise or gap fault.· Lost messageLost messageCheck soonCauses
- Internal speed sensor gap wrong
- Signal interference on the internal speed cable
Checks
- 1Check the internal sensor gap against the manual
- 2Compare the internal speed signal with the other speeds while running
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Shared checks
Checks, in order
- 1Check the sensor cable and connectors from the TCU to the transmission for chafing and corrosion
- 2Check the speed sensor gap and sensor face for damage or metal debris
- 3Check the sensor resistance or signal against a known-good sensor
- 4Look for a short to ground or battery voltage along the cable run
- 5Clear the code and see whether it comes back with the engine running
Causes
- Speed sensor gap wrong or sensor damaged
- Sensor cable chafed or connector corroded
- Temperature sensor failed
- A wiring short to ground or battery voltage
Most common here: shorted high (6 of 17)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: Shifting may become harsh, the TCU may fall back to substitute clutch control or a special gear selection mode, and the display shows a two character hex code.
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
