Deutz · EGR
Deutz Fault Code SPN 411 FMI 0
Engine - EGR differential pressure - Data above normal operational range (Most severe level)
What does Deutz code SPN 411 FMI 0 mean?
The EGR differential pressure sensor (on the EGR cooler or venturi, connected by two small pressure hoses) reports a value above the allowed range. Urgency: check soon - the machine may derate or limit a function. Check first: check the real value against a mechanical gauge or second reading before touching the EGR differential pressure sensor.
- FMI 0
- Data above normal, most severe
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the real value against a mechanical gauge or second reading before touching the EGR differential pressure sensor
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- A blocked downstream hose or heavy soot in the EGR path can give a genuine high differential reading
- Hose or port feeding the sensor blocked with dirt
- EGR differential pressure sensor drifting high or reading with an offset
How it failed
You'll notice: Warning or derate: EGR flow control is lost; expect reduced power, a lamp, and possibly a derate because the EMR4 cannot measure recirculated gas flow.
Real conditionRead from FMI 0: data above normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: EGR sensors: differential pressure, temperature and mass flow
4 other codes on this part are also real condition (SPN 2659 FMI 0, SPN 2659 FMI 1, SPN 523960 FMI 0, SPN 523960 FMI 1). When they show together, start at the wiring and connector they share.
- SPN 132 FMI 11Engine - Air mass - Root cause not knownOtherCheck soon
- SPN 411 FMI 0Engine - EGR differential pressure - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 411 FMI 2Engine - EGR differential pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 411 FMI 3Engine - EGR differential pressure - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 411 FMI 4Engine - EGR differential pressure - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 411 FMI 11Engine - EGR differential pressure - Root cause not knownOtherCheck soon
- SPN 412 FMI 3Engine - EGR temperature sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 412 FMI 4Engine - EGR temperature sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 2659 FMI 0Engine - EGR mass flow - Data above normal operational range (Most severe level)Real conditionCheck soon
Show the other 5 codesHide the other codes
- SPN 2659 FMI 1Engine - EGR mass flow - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 2659 FMI 2Engine - EGR mass flow - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 2659 FMI 12Engine - EGR mass flow - Bad intelligent device or componentPart or controllerCheck soon
- SPN 523960 FMI 0Engine - EGR temperature after EGR cooler - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 523960 FMI 1Engine - EGR temperature after EGR cooler - Data below normal operational range (Most severe level)Real conditionCheck soon
Other Deutz codes: EGR
- SPN 51 FMI 0Engine - Throttle valve / Throttle valve position - Data above normal operational range (Most severe level)
- SPN 51 FMI 1Engine - Throttle valve / Throttle valve position - Data below normal operational range (Most severe level)
- SPN 51 FMI 3Engine - Throttle valve / Throttle valve position - Voltage above normal or shorted to high source
- SPN 51 FMI 4Engine - Throttle valve / Throttle valve position - Voltage below normal or shorted to low source
- SPN 51 FMI 5Engine - Throttle valve / Throttle valve position - Current below normal or open circuit
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 14
This source lists SPN 411 FMI 0 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
