Deutz · Exhaust aftertreatment (DPF/DOC)
Deutz Fault Code SPN 3253 FMI 2
Exhaust aftertreatment - DPF differential pressure - Data erratic intermittent or incorrect
What does Deutz code SPN 3253 FMI 2 mean?
The EMR4 sees the DPF differential pressure sensor (on the machine side near the diesel particulate filter, with one hose before and one after the filter) signal jump or disagree with other values. Urgency: check soon - the machine may derate or limit a function. Check first: watch the DPF differential pressure sensor value in SerDia while wiggling the connector and harness.
- SPN 3253
- What is at fault
- FMI 2
- Erratic or incorrect data
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Watch the DPF differential pressure sensor value in SerDia while wiggling the connector and harness
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- Harness chafed against a bracket in a spot that only touches under vibration
- DPF differential pressure sensor on its way out
- Hoses swapped between inlet and outlet side
How it failed
You'll notice: The reading wanders and warnings come and go.
Erratic or implausibleRead from FMI 2: erratic or incorrect data
The reading jumps, drifts or disagrees with the sensors around it.
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DPF differential pressure, DPF and DOC temperature, and DPF load
3 other codes on this part are also erratic or implausible (SPN 3699 FMI 2, SPN 4768 FMI 2, SPN 4769 FMI 2). When they show together, start at the wiring and connector they share.
- SPN 3248 FMI 4Exhaust aftertreatment - Temperature after DPF - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 3251 FMI 0Exhaust aftertreatment - DPF differential pressure - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 3251 FMI 1Exhaust aftertreatment - DPF differential pressure - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 3253 FMI 2Exhaust aftertreatment - DPF differential pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 3253 FMI 3Exhaust aftertreatment - DPF differential pressure - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 3253 FMI 4Exhaust aftertreatment - DPF differential pressure - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 3699 FMI 0Exhaust aftertreatment - Passive regeneration - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 3699 FMI 2Exhaust aftertreatment - Passive regeneration - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 4765 FMI 0Exhaust aftertreatment - Temperature upstream DOC - Data above normal operational range (Most severe level)Real conditionCheck soon
Show the other 15 codesHide the other codes
- SPN 4766 FMI 0Exhaust aftertreatment - Temperature downstream DOC - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 4768 FMI 2Exhaust aftertreatment - Temperature sensor before DOC - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 4768 FMI 3Exhaust aftertreatment - Temperature sensor before DOC - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 4768 FMI 4Exhaust aftertreatment - Temperature sensor before DOC - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 4769 FMI 2Exhaust aftertreatment - Temperature sensor after DOC - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 4769 FMI 3Exhaust aftertreatment - Temperature sensor after DOC - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 4769 FMI 4Exhaust aftertreatment - Temperature sensor after DOC - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 524018 FMI 14Exhaust aftertreatment - DPF regeneration request - Special instructionsOtherInformation
- SPN 524022 FMI 14Exhaust aftertreatment - Soot load - Special instructionsOtherInformation
- SPN 524024 FMI 11Exhaust aftertreatment - DOC temperature difference - Root cause not knownOtherCheck soon
- SPN 524134 FMI 0Exhaust aftertreatment - DPF ash load - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 524135 FMI 0Exhaust aftertreatment - DPF soot load - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 524135 FMI 14Exhaust aftertreatment - DPF soot load - Special instructionsOtherInformation
- SPN 524283 FMI 12Exhaust aftertreatment - Swapped hoses for differential pressure sensor DPF - Bad intelligent device or componentPart or controllerCheck soon
- SPN 524284 FMI 12Exhaust aftertreatment - DOC removed - Bad intelligent device or componentPart or controllerCheck soon
Other Deutz codes: Exhaust aftertreatment (DPF/DOC)
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 14
This source lists SPN 3253 FMI 2 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
