EF Logo

Deutz · Exhaust aftertreatment (DPF/DOC)

Deutz Fault Code SPN 3251 FMI 0

Exhaust aftertreatment - DPF differential pressure - Data above normal operational range (Most severe level)

What does Deutz code SPN 3251 FMI 0 mean?

The DPF differential pressure (across the diesel particulate filter) reports a value above the allowed range. This is a plausibility limit, so the high value may be genuine rather than a wiring fault. Urgency: check soon - the machine may derate or limit a function. Check first: check the real value against a mechanical gauge or second reading before touching the DPF differential pressure.

FaultCheckSPN 3251FMI 0Deutz · Exhaust aftertreatment (DPF/DOC)
FMI 0
Data above normal, most severe

Can I keep running with it?

Check soon

The machine may derate or limit a function. Find the cause before the next shift.

What should I check first?

Check the real value against a mechanical gauge or second reading before touching the DPF differential pressure

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.

Checks

0 of 5 done

Causes

  • A heavily loaded or ash-plugged DPF causes a genuine high differential pressure; check the regeneration history
  • Hose or port feeding the sensor blocked with dirt
  • Cracked or missing filter substrate leaking exhaust past the element

How it failed

You'll notice: Warning or derate: the EMR4 sees a pressure drop across the DPF that is out of range; the DPF lamp can light and power can be reduced until regeneration or service is done.

Real conditionRead from FMI 0: data above normal, most severe

The sensor reading is valid but outside the allowed range - the problem may be real.

allowed rangetime
The reading against the band the controller allows.
Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good result
If the gauge agrees with the display, fix the machine, not the sensor.

When to stop

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Same part, other failures: DPF differential pressure, DPF and DOC temperature, and DPF load

6 other codes on this part are also real condition (SPN 3251 FMI 1, SPN 3699 FMI 0, SPN 4765 FMI 0, SPN 4766 FMI 0 and more). When they show together, start at the wiring and connector they share.

Show the other 15 codes
All 24 DPF differential pressure, DPF and DOC temperature, and DPF load codes on one page

Source

DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 15

This source lists SPN 3251 FMI 0 and its meaning. The guidance on this page is general, not taken from it.

The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.