Deutz · Injectors and combustion
Deutz Injector correction: IMA codes and zero quantity calibration fault codes
The learned and stored trims that keep each injector delivering the right quantity. The IMA code of each injector is stored in the EMR4 dataset (SPN 523895 to 523900, 523995, 523996).
More about these partsLess
The zero quantity calibration is a routine that trims each injector at idle (SPN 523946 onward) and reports when the correction runs out of range. Each code names the injector and whether its trim is out of calibration, too high or too low.
Where to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
What do these codes mean?
Deutz codes SPN 523895 FMI 13 to SPN 523996 FMI 13 are all about the injector correction: IMA codes and zero quantity calibration. Most are real condition faults; none needs an immediate stop. Start with this check: compare the IMA code printed on the injector with the one stored for that cylinder in SerDia.
How urgent are they?
None of the 17 codes here means stop now; all 17 can wait until the shift ends, but find the cause before the next one.
- Check soon17
What should I check first?
Compare the IMA code printed on the injector with the one stored for that cylinder in SerDia
Shared checks17 of 17
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Injector 1 IMA Code1 code
Deutz SPN 523895 FMI 13Injector 1 IMA Code: Out of calibration
The EMR4 reports the injector 1 IMA code as out of calibration. The injector correction code stored in the controller does not match the injector fitted, so fuel quantity cannot be trimmed correctly. Deutz list: KWP code 559, blink code 158. The IMA code of injector 1 is a number printed on the injector itself that the EMR4 uses to trim injector 1; a new injector brings a new code that has to be entered for cylinder 1. The usual symptom is a function that works but performs poorly, with the controller applying a default trim. A wrong IMA entry shows as one cylinder running richer or leaner than its neighbours, so compare cylinder 1 with cylinder 2 in the cylinder balance test; two injectors that were swapped during service give a pair of codes.· Part or controllerPart or controllerCheck soonCauses
- Injector 1 replaced and its IMA correction code not entered
- Code typed in wrong or from the wrong injector
- Controller replaced without transferring the injector codes
- Data set in the EMR4 corrupted
- Injector fitted from another engine, carrying a code that was never entered for this cylinder
Checks
- 1Re-enter or re-learn the injector codes with SerDia
- 2Check that every injector sits in the right cylinder
- 3Run a cylinder balance test afterwards to confirm the cylinder contributes evenly
- 4Compare injector 1 against the others in the injector data list
- 5Read the code printed on injector 1 and the entry for cylinder 1 in SerDia, and confirm that the two match digit for digit.
- 6After entering the code, switch the key off for the afterrun to complete and read the stored value again to confirm it was saved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Injector 2 IMA Code1 code
Deutz SPN 523896 FMI 13Injector 2 IMA Code: Out of calibration
The EMR4 reports the injector 2 IMA Code (stored for each injector in the EMR4 dataset) as out of calibration. Learned values or characteristics no longer match what the controller expects. Deutz list: KWP code 560, blink code 158. The IMA code of injector 2 is a number printed on the injector itself that the EMR4 uses to trim injector 2; a new injector brings a new code that has to be entered for cylinder 2. The usual symptom is a function that works but performs poorly, with the controller applying a default trim. A wrong IMA entry shows as one cylinder running richer or leaner than its neighbours, so compare cylinder 2 with cylinder 3 in the cylinder balance test; two injectors that were swapped during service give a pair of codes.· Part or controllerPart or controllerCheck soonCauses
- Part replaced without a calibration or learning routine
- Mechanical wear or play shifting the learned positions
- Injector fitted from another engine, carrying a code that was never entered for this cylinder
Checks
- 1Run the matching calibration or learn routine with the service tool, if available
- 2Check the part for mechanical play or a loose mounting that shifts its readings
- 3Read the code printed on injector 2 and the entry for cylinder 2 in SerDia, and confirm that the two match digit for digit.
- 4After entering the code, switch the key off for the afterrun to complete and read the stored value again to confirm it was saved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Injector 3 IMA Code1 code
Deutz SPN 523897 FMI 13Injector 3 IMA Code: Out of calibration
The EMR4 reports the injector 3 IMA Code (stored for each injector in the EMR4 dataset) as out of calibration. Learned values or characteristics no longer match what the controller expects. Deutz list: KWP code 561, blink code 158. The IMA code of injector 3 is a number printed on the injector itself that the EMR4 uses to trim injector 3; a new injector brings a new code that has to be entered for cylinder 3. The usual symptom is a function that works but performs poorly, with the controller applying a default trim. A wrong IMA entry shows as one cylinder running richer or leaner than its neighbours, so compare cylinder 3 with cylinder 4 in the cylinder balance test; two injectors that were swapped during service give a pair of codes.· Part or controllerPart or controllerCheck soonCauses
- Part replaced without a calibration or learning routine
- Mechanical wear or play shifting the learned positions
- Injector fitted from another engine, carrying a code that was never entered for this cylinder
Checks
- 1Run the matching calibration or learn routine with the service tool, if available
- 2Check the part for mechanical play or a loose mounting that shifts its readings
- 3Read the code printed on injector 3 and the entry for cylinder 3 in SerDia, and confirm that the two match digit for digit.
- 4After entering the code, switch the key off for the afterrun to complete and read the stored value again to confirm it was saved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Injector 4 IMA Code1 code
Deutz SPN 523898 FMI 13Injector 4 IMA Code: Out of calibration
The EMR4 reports the injector 4 IMA Code (stored for each injector in the EMR4 dataset) as out of calibration. Learned values or characteristics no longer match what the controller expects. Deutz list: KWP code 562, blink code 158. The IMA code of injector 4 is a number printed on the injector itself that the EMR4 uses to trim injector 4; a new injector brings a new code that has to be entered for cylinder 4. The usual symptom is a function that works but performs poorly, with the controller applying a default trim. A wrong IMA entry shows as one cylinder running richer or leaner than its neighbours, so compare cylinder 4 with cylinder 5 in the cylinder balance test; two injectors that were swapped during service give a pair of codes.· Part or controllerPart or controllerCheck soonCauses
- Part replaced without a calibration or learning routine
- Mechanical wear or play shifting the learned positions
- Injector fitted from another engine, carrying a code that was never entered for this cylinder
Checks
- 1Run the matching calibration or learn routine with the service tool, if available
- 2Check the part for mechanical play or a loose mounting that shifts its readings
- 3Read the code printed on injector 4 and the entry for cylinder 4 in SerDia, and confirm that the two match digit for digit.
- 4After entering the code, switch the key off for the afterrun to complete and read the stored value again to confirm it was saved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Injector 5 IMA Code1 code
Deutz SPN 523899 FMI 13Injector 5 IMA Code: Out of calibration
The EMR4 reports the injector 5 IMA Code (stored for each injector in the EMR4 dataset) as out of calibration. Learned values or characteristics no longer match what the controller expects. Deutz list: KWP code 563, blink code 158. The IMA code of injector 5 is a number printed on the injector itself that the EMR4 uses to trim injector 5; a new injector brings a new code that has to be entered for cylinder 5. The usual symptom is a function that works but performs poorly, with the controller applying a default trim. A wrong IMA entry shows as one cylinder running richer or leaner than its neighbours, so compare cylinder 5 with cylinder 6 in the cylinder balance test; two injectors that were swapped during service give a pair of codes.· Part or controllerPart or controllerCheck soonCauses
- Part replaced without a calibration or learning routine
- Mechanical wear or play shifting the learned positions
- Injector fitted from another engine, carrying a code that was never entered for this cylinder
Checks
- 1Run the matching calibration or learn routine with the service tool, if available
- 2Check the part for mechanical play or a loose mounting that shifts its readings
- 3Read the code printed on injector 5 and the entry for cylinder 5 in SerDia, and confirm that the two match digit for digit.
- 4After entering the code, switch the key off for the afterrun to complete and read the stored value again to confirm it was saved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Injector 6 IMA Code1 code
Deutz SPN 523900 FMI 13Injector 6 IMA Code: Out of calibration
The EMR4 reports the injector 6 IMA Code (stored for each injector in the EMR4 dataset) as out of calibration. Learned values or characteristics no longer match what the controller expects. Deutz list: KWP code 564, blink code 158. The IMA code of injector 6 is a number printed on the injector itself that the EMR4 uses to trim injector 6; a new injector brings a new code that has to be entered for cylinder 6. The usual symptom is a function that works but performs poorly, with the controller applying a default trim. A wrong IMA entry shows as one cylinder running richer or leaner than its neighbours, so compare cylinder 6 with cylinder 7 in the cylinder balance test; two injectors that were swapped during service give a pair of codes.· Part or controllerPart or controllerCheck soonCauses
- Part replaced without a calibration or learning routine
- Mechanical wear or play shifting the learned positions
- Injector fitted from another engine, carrying a code that was never entered for this cylinder
Checks
- 1Run the matching calibration or learn routine with the service tool, if available
- 2Check the part for mechanical play or a loose mounting that shifts its readings
- 3Read the code printed on injector 6 and the entry for cylinder 6 in SerDia, and confirm that the two match digit for digit.
- 4After entering the code, switch the key off for the afterrun to complete and read the stored value again to confirm it was saved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Injection Zero quantity calibration Injector 12 codes
Deutz SPN 523946 FMI 0Injection Zero quantity calibration Injector 1: Reading too high· most severe
The EMR4 rates the injection Zero quantity calibration Injector 1 (a learning routine in the EMR4 that trims each injector at idle) as above its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1158, blink code 772. The zero quantity calibration of injector 1 is above range: the idle trim for cylinder 1 has run to its upper limit, so the EMR4 is adding more fuel for it than it can allow, as a worn or leaking injector would force. The usual symptom is a warning and a limited function while the value stays above its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 1 with cylinder 2, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really above its limit, for example from overload or a blockage
- Signal or part drifting high with age
- Injector nozzle worn or leaking, so the idle trim has to add fuel to compensate
Checks
- 1Read the injection Zero quantity calibration Injector 1 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of an excessive value, such as a restriction or an overloaded function
- 3Compare the idle trim of cylinder 1 with the others and check injector 1 for a leaking tip or stuck needle.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 1 - Data above normal operational range (Most severe level)
Deutz SPN 523946 FMI 1Injection Zero quantity calibration Injector 1: Reading too low· most severe
The EMR4 rates the injection Zero quantity calibration Injector 1 (a learning routine in the EMR4 that trims each injector at idle) as below its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1164, blink code 772. The zero quantity calibration of injector 1 is below range: the idle trim for cylinder 1 has run to its lower limit, so the EMR4 is taking fuel away, as an injector that delivers too much would force. The usual symptom is a warning and a limited function while the value stays below its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 1 with cylinder 2, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really below its limit, for example a leak, a blockage or a part not working
- Signal or part drifting low with age
- Injector delivering more than its label says, so the idle trim has to take fuel away
Checks
- 1Read the injection Zero quantity calibration Injector 1 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of a low value, such as a leak, a blocked line or a weak supply
- 3Compare the idle trim of cylinder 1 with the others and check injector 1 for a sticking open nozzle or too much return flow.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 1 - Data below normal operational range (Most severe level)
Injection Zero quantity calibration Injector 22 codes
Deutz SPN 523947 FMI 0Injection Zero quantity calibration Injector 2: Reading too high· most severe
The EMR4 rates the injection Zero quantity calibration Injector 2 (a learning routine in the EMR4 that trims each injector at idle) as above its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1159, blink code 772. The zero quantity calibration of injector 2 is above range: the idle trim for cylinder 2 has run to its upper limit, so the EMR4 is adding more fuel for it than it can allow, as a worn or leaking injector would force. The usual symptom is a warning and a limited function while the value stays above its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 2 with cylinder 3, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really above its limit, for example from overload or a blockage
- Signal or part drifting high with age
- Injector nozzle worn or leaking, so the idle trim has to add fuel to compensate
Checks
- 1Read the injection Zero quantity calibration Injector 2 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of an excessive value, such as a restriction or an overloaded function
- 3Compare the idle trim of cylinder 2 with the others and check injector 2 for a leaking tip or stuck needle.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 2 - Data above normal operational range (Most severe level)
Deutz SPN 523947 FMI 1Injection Zero quantity calibration Injector 2: Reading too low· most severe
The EMR4 rates the injection Zero quantity calibration Injector 2 (a learning routine in the EMR4 that trims each injector at idle) as below its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1165, blink code 772. The zero quantity calibration of injector 2 is below range: the idle trim for cylinder 2 has run to its lower limit, so the EMR4 is taking fuel away, as an injector that delivers too much would force. The usual symptom is a warning and a limited function while the value stays below its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 2 with cylinder 3, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really below its limit, for example a leak, a blockage or a part not working
- Signal or part drifting low with age
- Injector delivering more than its label says, so the idle trim has to take fuel away
Checks
- 1Read the injection Zero quantity calibration Injector 2 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of a low value, such as a leak, a blocked line or a weak supply
- 3Compare the idle trim of cylinder 2 with the others and check injector 2 for a sticking open nozzle or too much return flow.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 2 - Data below normal operational range (Most severe level)
Injection Zero quantity calibration Injector 32 codes
Deutz SPN 523948 FMI 0Injection Zero quantity calibration Injector 3: Reading too high· most severe
The EMR4 rates the injection Zero quantity calibration Injector 3 (a learning routine in the EMR4 that trims each injector at idle) as above its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1160, blink code 772. The zero quantity calibration of injector 3 is above range: the idle trim for cylinder 3 has run to its upper limit, so the EMR4 is adding more fuel for it than it can allow, as a worn or leaking injector would force. The usual symptom is a warning and a limited function while the value stays above its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 3 with cylinder 4, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really above its limit, for example from overload or a blockage
- Signal or part drifting high with age
- Injector nozzle worn or leaking, so the idle trim has to add fuel to compensate
Checks
- 1Read the injection Zero quantity calibration Injector 3 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of an excessive value, such as a restriction or an overloaded function
- 3Compare the idle trim of cylinder 3 with the others and check injector 3 for a leaking tip or stuck needle.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 3 - Data above normal operational range (Most severe level)
Deutz SPN 523948 FMI 1Injection Zero quantity calibration Injector 3: Reading too low· most severe
The EMR4 rates the injection Zero quantity calibration Injector 3 (a learning routine in the EMR4 that trims each injector at idle) as below its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1166, blink code 772. The zero quantity calibration of injector 3 is below range: the idle trim for cylinder 3 has run to its lower limit, so the EMR4 is taking fuel away, as an injector that delivers too much would force. The usual symptom is a warning and a limited function while the value stays below its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 3 with cylinder 4, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really below its limit, for example a leak, a blockage or a part not working
- Signal or part drifting low with age
- Injector delivering more than its label says, so the idle trim has to take fuel away
Checks
- 1Read the injection Zero quantity calibration Injector 3 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of a low value, such as a leak, a blocked line or a weak supply
- 3Compare the idle trim of cylinder 3 with the others and check injector 3 for a sticking open nozzle or too much return flow.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 3 - Data below normal operational range (Most severe level)
Injection Zero quantity calibration Injector 41 code
Deutz SPN 523949 FMI 1Injection Zero quantity calibration Injector 4: Reading too low· most severe
The EMR4 rates the injection Zero quantity calibration Injector 4 (a learning routine in the EMR4 that trims each injector at idle) as below its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1167, blink code 772. The zero quantity calibration of injector 4 is below range: the idle trim for cylinder 4 has run to its lower limit, so the EMR4 is taking fuel away, as an injector that delivers too much would force. The usual symptom is a warning and a limited function while the value stays below its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 4 with cylinder 5, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really below its limit, for example a leak, a blockage or a part not working
- Signal or part drifting low with age
- Injector delivering more than its label says, so the idle trim has to take fuel away
Checks
- 1Read the injection Zero quantity calibration Injector 4 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of a low value, such as a leak, a blocked line or a weak supply
- 3Compare the idle trim of cylinder 4 with the others and check injector 4 for a sticking open nozzle or too much return flow.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 4 - Data below normal operational range (Most severe level)
Injection Zero quantity calibration Injector 51 code
Deutz SPN 523950 FMI 1Injection Zero quantity calibration Injector 5: Reading too low· most severe
The EMR4 rates the injection Zero quantity calibration Injector 5 (a learning routine in the EMR4 that trims each injector at idle) as below its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1168, blink code 772. The zero quantity calibration of injector 5 is below range: the idle trim for cylinder 5 has run to its lower limit, so the EMR4 is taking fuel away, as an injector that delivers too much would force. The usual symptom is a warning and a limited function while the value stays below its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 5 with cylinder 6, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really below its limit, for example a leak, a blockage or a part not working
- Signal or part drifting low with age
- Injector delivering more than its label says, so the idle trim has to take fuel away
Checks
- 1Read the injection Zero quantity calibration Injector 5 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of a low value, such as a leak, a blocked line or a weak supply
- 3Compare the idle trim of cylinder 5 with the others and check injector 5 for a sticking open nozzle or too much return flow.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 5 - Data below normal operational range (Most severe level)
Injection Zero quantity calibration Injector 61 code
Deutz SPN 523951 FMI 0Injection Zero quantity calibration Injector 6: Reading too high· most severe
The EMR4 rates the injection Zero quantity calibration Injector 6 (a learning routine in the EMR4 that trims each injector at idle) as above its allowed operating range, at the most severe level. The value may be real, or a plausibility limit has tripped. Deutz list: KWP code 1163, blink code 772. The zero quantity calibration of injector 6 is above range: the idle trim for cylinder 6 has run to its upper limit, so the EMR4 is adding more fuel for it than it can allow, as a worn or leaking injector would force. The usual symptom is a warning and a limited function while the value stays above its limit. The trim only moves slowly while the engine idles warm, so give the engine several minutes at idle after any repair and compare cylinder 6 with cylinder 7, because a single outlier points at the injector and not at the fuel supply.· Real conditionReal conditionCheck soonCauses
- The monitored condition is really above its limit, for example from overload or a blockage
- Signal or part drifting high with age
- Injector nozzle worn or leaking, so the idle trim has to add fuel to compensate
Checks
- 1Read the injection Zero quantity calibration Injector 6 value in SerDia and compare it with an independent measurement before replacing parts
- 2Look for the real cause of an excessive value, such as a restriction or an overloaded function
- 3Compare the idle trim of cylinder 6 with the others and check injector 6 for a leaking tip or stuck needle.
- 4Run the idle quantity learn again after the injector check and compare the new trim with the old one.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Injection Zero quantity calibration Injector 6 - Data above normal operational range (Most severe level)
Injector 7 IMA Code1 code
Deutz SPN 523995 FMI 13Injector 7 IMA Code: Out of calibration
The EMR4 reports the injector 7 IMA Code (stored for each injector in the EMR4 dataset) as out of calibration. Learned values or characteristics no longer match what the controller expects. Deutz list: KWP code 1324, blink code 7-9-5. The IMA code of injector 7 is a number printed on the injector itself that the EMR4 uses to trim injector 7; a new injector brings a new code that has to be entered for cylinder 7. The usual symptom is a function that works but performs poorly, with the controller applying a default trim. A wrong IMA entry shows as one cylinder running richer or leaner than its neighbours, so compare cylinder 7 with cylinder 8 in the cylinder balance test; two injectors that were swapped during service give a pair of codes.· Part or controllerPart or controllerCheck soonCauses
- Part replaced without a calibration or learning routine
- Mechanical wear or play shifting the learned positions
- Injector fitted from another engine, carrying a code that was never entered for this cylinder
Checks
- 1Run the matching calibration or learn routine with the service tool, if available
- 2Check the part for mechanical play or a loose mounting that shifts its readings
- 3Read the code printed on injector 7 and the entry for cylinder 7 in SerDia, and confirm that the two match digit for digit.
- 4After entering the code, switch the key off for the afterrun to complete and read the stored value again to confirm it was saved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Injector 8 IMA Code1 code
Deutz SPN 523996 FMI 13Injector 8 IMA Code: Out of calibration
The EMR4 reports the injector 8 IMA Code (stored for each injector in the EMR4 dataset) as out of calibration. Learned values or characteristics no longer match what the controller expects. Deutz list: KWP code 1325, blink code 7-9-6. The IMA code of injector 8 is a number printed on the injector itself that the EMR4 uses to trim injector 8; a new injector brings a new code that has to be entered for cylinder 8. The usual symptom is a function that works but performs poorly, with the controller applying a default trim. A wrong IMA entry shows as one cylinder running richer or leaner than its neighbours, so compare cylinder 8 with cylinder 7 in the cylinder balance test; two injectors that were swapped during service give a pair of codes.· Part or controllerPart or controllerCheck soonCauses
- Part replaced without a calibration or learning routine
- Mechanical wear or play shifting the learned positions
- Injector fitted from another engine, carrying a code that was never entered for this cylinder
Checks
- 1Run the matching calibration or learn routine with the service tool, if available
- 2Check the part for mechanical play or a loose mounting that shifts its readings
- 3Read the code printed on injector 8 and the entry for cylinder 8 in SerDia, and confirm that the two match digit for digit.
- 4After entering the code, switch the key off for the afterrun to complete and read the stored value again to confirm it was saved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Shared checks
Checks, in order
- 1Compare the IMA code printed on the injector with the one stored for that cylinder in SerDia
- 2Re-enter or re-program the injector codes with SerDia and confirm the entry was accepted
- 3Read the learned correction per cylinder and look for one cylinder far from the others
- 4Check injector return flow and fuel quality before resetting learned values
- 5Run a cylinder balance test afterwards to confirm the cylinder contributes evenly
Causes
- Injector replaced without entering its new IMA code
- IMA code typed wrongly or for the wrong cylinder, or the controller replaced without transferring the codes
- Worn or leaking injector pushing the learned value to its limit
- Fuel contamination or air in the fuel upsetting the learning
Most codes here: real condition (9 of 17)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: A warning lamp or limited function.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
