Detroit · Aftertreatment
Detroit Soot sensor fault codes
The soot sensor sits in the exhaust after the DPF and detects particulate that passes through. Detroit logs its electrode and heater circuits, temperature plausibility and CAN link.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 574 FMI 4 to SPN 520362 FMI 4 are all about the soot sensor. The most common failure type is real condition (7 of 29); none needs an immediate stop. Start with this check: inspect the soot sensor connector for moisture, corrosion and bent pins.
How urgent are they?
None of the 29 codes here means stop now; all 29 can wait until the shift ends, but find the cause before the next one.
- Check soon29
What should I check first?
Inspect the soot sensor connector for moisture, corrosion and bent pins.
Shared checks29 of 29
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 574 FMI 4Soot Sensor Inter-Digital Electrode Short Circuit
Detroit lists SPN 574 FMI 4 as "Soot Sensor Inter-Digital Electrode Short Circuit". The ACM saw the soot sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The soot sensor electrodes measure particulate leaking through the DPF; a short across the comb electrodes is read as a circuit fault.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The soot sensor has failed inside or its supply wire is open
Checks
- 1Unplug the soot sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the ACM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 5319 FMI 14Soot Sensor Regeneration Error
Detroit lists SPN 5319 FMI 14 as "Soot Sensor Regeneration Error". The ACM judged the soot sensor reading erratic or not plausible compared with other sensors or its own history. The soot sensor can run a regeneration of its own element; failure of that routine is logged here.· Lost messageLost messageCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting soot sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the soot sensor reading with a second reference such as a gauge or another sensor on the engine.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 5569 FMI 3Soot Sensor Printed Circuit Board Temperature 1 Signal Range High
Detroit lists SPN 5569 FMI 3 as "Soot Sensor Printed Circuit Board Temperature 1 Signal Range High". The ACM saw the soot sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The soot sensor board has temperature sensors; signal range faults show whether the sensor circuit board is damaged.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the soot sensor and the ACM
- The soot sensor has failed inside
Checks
- 1Unplug the soot sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 5569 FMI 4Soot Sensor Printed Circuit Board Temperature 1 Signal Range Low
Detroit lists SPN 5569 FMI 4 as "Soot Sensor Printed Circuit Board Temperature 1 Signal Range Low". The ACM saw the soot sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The soot sensor board has temperature sensors; signal range faults show whether the sensor circuit board is damaged.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The soot sensor has failed inside or its supply wire is open
Checks
- 1Unplug the soot sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the ACM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 5741 FMI 9Soot Sensor Communication Error
Detroit lists SPN 5741 FMI 9 as "Soot Sensor Communication Error". The ACM lost the soot sensor signal completely. The soot sensor sends its readings by CAN; the faults describe communication, electrode and range problems.· Lost messageLost messageCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the soot sensor.
- 2Check the signal wire to the ACM for an open.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 5741 FMI 12Soot Sensor Inter-Digital Electrode Self-Diagnostic
Detroit lists SPN 5741 FMI 12 as "Soot Sensor Inter-Digital Electrode Self-Diagnostic". The ACM lost the soot sensor signal completely. The soot sensor sends its readings by CAN; the faults describe communication, electrode and range problems.· Part or controllerPart or controllerCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the soot sensor.
- 2Check the signal wire to the ACM for an open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 5741 FMI 13Soot Sensor Controller Area Network (CAN) Feedback Signal Failure
Detroit lists SPN 5741 FMI 13 as "Soot Sensor Controller Area Network (CAN) Feedback Signal Failure". The ACM found the soot sensor value drifted away from what the engine state says it should be. The soot sensor sends its readings by CAN; the faults describe communication, electrode and range problems.· Part or controllerPart or controllerCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the soot sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the soot sensor for leaks, restrictions or contamination.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 5741 FMI 16Soot Sensor Data Valid But Above Normal Operating Range· moderately severe
Detroit lists SPN 5741 FMI 16 as "Soot Sensor Data Valid But Above Normal Operating Range - Moderately Severe Level". The ACM reports that the measured value itself is out of its normal range; the soot sensor may be correct and a real condition may exist. The soot sensor sends its readings by CAN; the faults describe communication, electrode and range problems.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the soot sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the soot sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Soot Sensor Data Valid But Above Normal Operating Range - Moderately Severe Level
Detroit SPN 5741 FMI 18Soot Sensor Data Valid But Below Normal Operating Range· moderately severe
Detroit lists SPN 5741 FMI 18 as "Soot Sensor Data Valid But Below Normal Operating Range - Moderately Severe Level". The ACM reports that the measured value itself is out of its normal range; the soot sensor may be correct and a real condition may exist. The soot sensor sends its readings by CAN; the faults describe communication, electrode and range problems.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the soot sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the soot sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Soot Sensor Data Valid But Below Normal Operating Range - Moderately Severe Level
Detroit SPN 5747 FMI 12Soot Sensor Heater Fault
Detroit lists SPN 5747 FMI 12 as "Soot Sensor Heater Fault". The ACM lost the soot sensor signal completely. The soot sensor heater keeps the element clean and hot; a fault stops the sensor from working correctly.· Part or controllerPart or controllerCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the soot sensor.
- 2Check the signal wire to the ACM for an open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 520348 FMI 14Soot Sensor Tube Clogged / Defect
Detroit lists SPN 520348 FMI 14 as "Soot Sensor Tube Clogged / Defect". The ACM judged the soot sensor reading erratic or not plausible compared with other sensors or its own history. The soot sensor tube is clogged or defective, so it cannot sense particles properly.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting soot sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the soot sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 520352 FMI 3Supply Voltage Difference Between ACM and Soot Sensor
Detroit lists SPN 520352 FMI 3 as "Supply Voltage Difference Between ACM and Soot Sensor". The ACM saw the soot sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The supply voltage difference between the ACM and the soot sensor is out of range, pointing to a supply wire problem.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the soot sensor and the ACM
- The soot sensor has failed inside
Checks
- 1Unplug the soot sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 520353 FMI 17Soot Sensor Temperature Rationality Failure - Cold Start
Detroit lists SPN 520353 FMI 17 as "Soot Sensor Temperature Rationality Failure - Cold Start". The ACM reports that the measured value itself is out of its normal range; the soot sensor may be correct and a real condition may exist. The soot sensor temperature failed its cold start plausibility check.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the soot sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the soot sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520357 FMI 2Soot Sensor Printed Circuit Board Temperature Rationality Fault
Same failure as SPN 520353 FMI 17 ("Soot Sensor Temperature Rationality Failure - Cold Start") on a sibling part: Detroit lists SPN 520357 FMI 2 as "Soot Sensor Printed Circuit Board Temperature Rationality Fault". The soot sensor board temperature is not plausible or too high.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 520353 FMI 17, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 520353 FMI 17, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 520357 FMI 15Soot Sensor Printed Circuit Board Temperature High
Detroit lists SPN 520357 FMI 15 as "Soot Sensor Printed Circuit Board Temperature High". The ACM reports that the measured value itself is out of its normal range; the soot sensor may be correct and a real condition may exist. The soot sensor board temperature is not plausible or too high.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the soot sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the soot sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520358 FMI 3Soot Sensor Printed Circuit Board Temperature 2 Signal Range High
Same failure as SPN 5569 FMI 3 ("Soot Sensor Printed Circuit Board Temperature 1 Signal Range High") on a sibling part: Detroit lists SPN 520358 FMI 3 as "Soot Sensor Printed Circuit Board Temperature 2 Signal Range High". Soot sensor board temperature channel 2 has a signal range fault.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 5569 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5569 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 520358 FMI 4Soot Sensor Printed Circuit Board Temperature 2 Signal Range Low
Same failure as SPN 5569 FMI 4 ("Soot Sensor Printed Circuit Board Temperature 1 Signal Range Low") on a sibling part: Detroit lists SPN 520358 FMI 4 as "Soot Sensor Printed Circuit Board Temperature 2 Signal Range Low". Soot sensor board temperature channel 2 has a signal range fault.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 5569 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5569 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 520359 FMI 3Soot Sensor Heater Short Circuit to Battery
Same failure as SPN 5569 FMI 3 ("Soot Sensor Printed Circuit Board Temperature 1 Signal Range High") on a sibling part: Detroit lists SPN 520359 FMI 3 as "Soot Sensor Heater Short Circuit to Battery". The soot sensor heater has a short, an open load or a board component failure.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 5569 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5569 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 520359 FMI 4Lower than expected heater circuit voltage
Detroit lists SPN 520359 FMI 4 as "Lower than expected heater circuit voltage". The ACM saw the soot sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The soot sensor heater has a short, an open load or a board component failure.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The soot sensor has failed inside or its supply wire is open
Checks
- 1Unplug the soot sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the ACM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 520359 FMI 5Soot Sensor Heater Open Load
Detroit lists SPN 520359 FMI 5 as "Soot Sensor Heater Open Load". The ACM detected an open circuit on the soot sensor line, so the signal floats or is missing. The soot sensor heater has a short, an open load or a board component failure.· Open circuitOpen circuitCheck soonCauses
- Broken wire or a pushed-out pin in the soot sensor connector
- Corroded terminal or a failed sensor
Checks
- 1Check continuity of every wire between the soot sensor connector and the ACM connector.
- 2Wiggle the harness and connector while watching the live value for dropouts.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 520359 FMI 12Soot Sensor Heater Printed Circuit Board Component Failure
Detroit lists SPN 520359 FMI 12 as "Soot Sensor Heater Printed Circuit Board Component Failure". The ACM lost the soot sensor signal completely. The soot sensor heater has a short, an open load or a board component failure.· Part or controllerPart or controllerCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the soot sensor.
- 2Check the signal wire to the ACM for an open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 520360 FMI 3Soot Sensor Inter-Digital Electrode Positive Short Circuit to Battery Diagnostic
Same failure as SPN 5569 FMI 3 ("Soot Sensor Printed Circuit Board Temperature 1 Signal Range High") on a sibling part: Detroit lists SPN 520360 FMI 3 as "Soot Sensor Inter-Digital Electrode Positive Short Circuit to Battery Diagnostic". The soot sensor inter-digital electrode positive line is shorted to battery, to ground or out of range.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 5569 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5569 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 520360 FMI 4Soot Sensor Inter-Digital Electrode Positive Short Circuit to Ground Diagnostic
Same failure as SPN 5569 FMI 4 ("Soot Sensor Printed Circuit Board Temperature 1 Signal Range Low") on a sibling part: Detroit lists SPN 520360 FMI 4 as "Soot Sensor Inter-Digital Electrode Positive Short Circuit to Ground Diagnostic". The soot sensor inter-digital electrode positive line is shorted to battery, to ground or out of range.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 5569 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5569 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 520360 FMI 15Soot Sensor Inter-Digital Electrode Positive Signal Range High Diagnostic
Same failure as SPN 5569 FMI 3 ("Soot Sensor Printed Circuit Board Temperature 1 Signal Range High") on a sibling part: Detroit lists SPN 520360 FMI 15 as "Soot Sensor Inter-Digital Electrode Positive Signal Range High Diagnostic". The soot sensor inter-digital electrode positive line is shorted to battery, to ground or out of range.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 5569 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5569 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520361 FMI 2Soot Sensor Temperature Rationality Signal Range Low
Same failure as SPN 5569 FMI 4 ("Soot Sensor Printed Circuit Board Temperature 1 Signal Range Low") on a sibling part: Detroit lists SPN 520361 FMI 2 as "Soot Sensor Temperature Rationality Signal Range Low". The soot sensor temperature is out of the expected range or not plausible.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 5569 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5569 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 520361 FMI 16Soot Sensor Temperature High
Detroit lists SPN 520361 FMI 16 as "Soot Sensor Temperature High". The ACM reports that the measured value itself is out of its normal range; the soot sensor may be correct and a real condition may exist. The soot sensor temperature is out of the expected range or not plausible.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the soot sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the soot sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520361 FMI 18Soot Sensor Temperature Low
Detroit lists SPN 520361 FMI 18 as "Soot Sensor Temperature Low". The ACM reports that the measured value itself is out of its normal range; the soot sensor may be correct and a real condition may exist. The soot sensor temperature is out of the expected range or not plausible.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the soot sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the soot sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520362 FMI 3Soot Sensor Supply Line Voltage Above Normal, or Shorted To High Source
Same failure as SPN 520352 FMI 3 ("Supply Voltage Difference Between ACM and Soot Sensor") on a sibling part: Detroit lists SPN 520362 FMI 3 as "Soot Sensor Supply Line Voltage Above Normal, or Shorted To High Source". The soot sensor supply line is high or low.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 520352 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 520352 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 520362 FMI 4Soot Sensor Supply Line Signal Range Low
Same failure as SPN 520352 FMI 3 ("Supply Voltage Difference Between ACM and Soot Sensor") on a sibling part: Detroit lists SPN 520362 FMI 4 as "Soot Sensor Supply Line Signal Range Low". The soot sensor supply line is high or low.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 520352 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 520352 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Shared checks
Checks, in order
- 1Inspect the soot sensor connector for moisture, corrosion and bent pins.
- 2Check the wiring between the soot sensor and its control unit for chafing and heat damage.
- 3Read the soot sensor data and temperature values in the diagnostic tool.
- 4Check the DPF for cracks or a missing filter element if the filtration code is set.
Causes
- Soot sensor connector or wiring damage
- Contaminated or damaged sensor element
- Sensor heater failure
- DPF damage
Most common here: real condition (7 of 29)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: A check-engine lamp and possibly a derate; the DPF monitoring may be disabled.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
