Detroit · Aftertreatment
Detroit SCR catalyst temperature and NOx conversion fault codes
The ACM monitors the temperatures around the SCR catalyst and the conversion efficiency. Detroit logs sensor faults and low-efficiency conditions.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 4360 FMI 15 to SPN 520372 FMI 16 are all about the sCR catalyst temperature and NOx conversion. The most common failure type is real condition (8 of 17); none needs an immediate stop. Start with this check: check the DEF quality and the dosing rate before blaming the catalyst.
How urgent are they?
None of the 17 codes here means stop now; all 17 can wait until the shift ends, but find the cause before the next one.
- Check soon17
What should I check first?
Check the DEF quality and the dosing rate before blaming the catalyst.
Shared checks17 of 17
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 4360 FMI 15Selective Catalyst Reduction Inlet Temperature High
Detroit lists SPN 4360 FMI 15 as "Selective Catalyst Reduction Inlet Temperature High". The ACM reports that the measured value itself is out of its normal range; the SCR temperature or conversion signal may be correct and a real condition may exist. The SCR inlet temperature sensor shows the exhaust heat entering the catalyst; the ACM only doses when it is warm enough.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the SCR temperature or conversion signal measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the SCR temperature or conversion signal.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4360 FMI 20Selective Catalyst Reduction Inlet Temperature Sensor Drift High in Range
Detroit lists SPN 4360 FMI 20 as "Selective Catalyst Reduction Inlet Temperature Sensor Drift High in Range". The ACM found the SCR temperature or conversion signal value drifted away from what the engine state says it should be. The SCR inlet temperature sensor shows the exhaust heat entering the catalyst; the ACM only doses when it is warm enough.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the SCR temperature or conversion signal reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the SCR temperature or conversion signal for leaks, restrictions or contamination.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 4360 FMI 31Selective Catalyst Reduction Inlet Temperature Not Warming Up
Detroit lists SPN 4360 FMI 31 as "Selective Catalyst Reduction Inlet Temperature Not Warming Up". The ACM logged a condition on the SCR temperature or conversion signal; the title says what it measured. The SCR inlet temperature sensor shows the exhaust heat entering the catalyst; the ACM only doses when it is warm enough.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the SCR temperature or conversion signal watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4363 FMI 0SCR Outlet Temperature High
Detroit lists SPN 4363 FMI 0 as "SCR Outlet Temperature High". The ACM reports that the measured value itself is out of its normal range; the SCR temperature or conversion signal may be correct and a real condition may exist. The SCR outlet temperature sensor shows the heat leaving the catalyst and is compared with the inlet value.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the SCR temperature or conversion signal measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the SCR temperature or conversion signal.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4363 FMI 2Selective Catalyst Reduction Outlet Temperature - Not Plausible
Detroit lists SPN 4363 FMI 2 as "Selective Catalyst Reduction Outlet Temperature - Not Plausible". The ACM judged the SCR temperature or conversion signal reading erratic or not plausible compared with other sensors or its own history. The SCR outlet temperature sensor shows the heat leaving the catalyst and is compared with the inlet value.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting SCR temperature or conversion signal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the SCR temperature or conversion signal reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 4363 FMI 3Selective Catalyst Reduction Outlet Temperature Sensor Circuit Failed High
Detroit lists SPN 4363 FMI 3 as "Selective Catalyst Reduction Outlet Temperature Sensor Circuit Failed High". The ACM saw the SCR temperature or conversion signal signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The SCR outlet temperature sensor shows the heat leaving the catalyst and is compared with the inlet value.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the SCR temperature or conversion signal and the ACM
- The SCR temperature or conversion signal has failed inside
Checks
- 1Unplug the SCR temperature or conversion signal and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 4363 FMI 4Selective Catalyst Reduction Outlet Temperature Sensor Circuit Failed Low
Detroit lists SPN 4363 FMI 4 as "Selective Catalyst Reduction Outlet Temperature Sensor Circuit Failed Low". The ACM saw the SCR temperature or conversion signal signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The SCR outlet temperature sensor shows the heat leaving the catalyst and is compared with the inlet value.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The SCR temperature or conversion signal has failed inside or its supply wire is open
Checks
- 1Unplug the SCR temperature or conversion signal and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the ACM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 4363 FMI 8SCR Outlet Temperature Signal Spike
Detroit lists SPN 4363 FMI 8 as "SCR Outlet Temperature Signal Spike". The ACM judged the SCR temperature or conversion signal reading erratic or not plausible compared with other sensors or its own history. The SCR outlet temperature sensor shows the heat leaving the catalyst and is compared with the inlet value.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting SCR temperature or conversion signal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the SCR temperature or conversion signal reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 4363 FMI 10SCR Outlet Temperature Sensor - Rationality Error
Same failure as SPN 4363 FMI 2 ("Selective Catalyst Reduction Outlet Temperature - Not Plausible") on a sibling part: Detroit lists SPN 4363 FMI 10 as "SCR Outlet Temperature Sensor - Rationality Error". The SCR outlet temperature sensor shows the heat leaving the catalyst and is compared with the inlet value.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 4363 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 4363 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 4363 FMI 20SCR Temperature Drift - Inlet Low/Outlet High
Same failure as SPN 4360 FMI 20 ("Selective Catalyst Reduction Inlet Temperature Sensor Drift High in Range") on a sibling part: Detroit lists SPN 4363 FMI 20 as "SCR Temperature Drift - Inlet Low/Outlet High". The SCR outlet temperature sensor shows the heat leaving the catalyst and is compared with the inlet value.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 4360 FMI 20, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 4360 FMI 20, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 4364 FMI 1SCR NOx Conversion Efficiency Very Low
The ACM calculated that the SCR catalyst is converting NOx at a very low efficiency. Detroit uses this to warn about the emissions system, and it can lead to a derate if it stays active.· Real conditionReal conditionCheck soonCauses
- Poor DEF quality or dilute fluid
- Plugged or leaking DEF doser, or insufficient dosing
- Failed or drifting NOx sensors giving a wrong efficiency
- Aged or damaged SCR catalyst
Checks
- 1Test the DEF concentration with a refractometer and replace the fluid if it is dilute.
- 2Inspect the doser nozzle for crystal build-up and check the DEF lines.
- 3Compare the inlet and outlet NOx sensor values in the tool; they should differ when dosing works.
- 4Check the exhaust for leaks between the turbo and the catalyst.
- 5Only replace the catalyst after dosing, quality and sensors are proven good.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4364 FMI 17SCR NOx Conversion Efficiency
Detroit lists SPN 4364 FMI 17 as "SCR NOx Conversion Efficiency". The ACM reports that the measured value itself is out of its normal range; the SCR temperature or conversion signal may be correct and a real condition may exist. SCR conversion efficiency is the share of NOx the catalyst removes, worked out from the inlet and outlet NOx sensors.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the SCR temperature or conversion signal measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the SCR temperature or conversion signal.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4364 FMI 31SCR NOx Efficiency Low
Detroit lists SPN 4364 FMI 31 as "SCR NOx Efficiency Low". The ACM logged a condition on the SCR temperature or conversion signal; the title says what it measured. SCR conversion efficiency is the share of NOx the catalyst removes, worked out from the inlet and outlet NOx sensors.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the SCR temperature or conversion signal watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 5298 FMI 14Selective Catalytic Reduction Catalyst Abnormal Temperature Rise
Detroit lists SPN 5298 FMI 14 as "Selective Catalytic Reduction Catalyst Abnormal Temperature Rise". The ACM judged the SCR temperature or conversion signal reading erratic or not plausible compared with other sensors or its own history. An abnormal temperature rise in the SCR catalyst can mean fuel or soot is burning in it.· Lost messageLost messageCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting SCR temperature or conversion signal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the SCR temperature or conversion signal reading with a second reference such as a gauge or another sensor on the engine.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 520371 FMI 16Selective Catalyst Reduction Closed Loop Control at Maximum Limit (Multiples Sources)
Detroit lists SPN 520371 FMI 16 as "Selective Catalyst Reduction Closed Loop Control at Maximum Limit (Multiples Sources)". The ACM reports that the measured value itself is out of its normal range; the SCR temperature or conversion signal may be correct and a real condition may exist. SCR closed loop control reached the maximum limit from several sources.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the SCR temperature or conversion signal measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the SCR temperature or conversion signal.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520372 FMI 14Selective Catalyst Reduction Closed Loop Control at Maximum Limit (Timeout)
Detroit lists SPN 520372 FMI 14 as "Selective Catalyst Reduction Closed Loop Control at Maximum Limit (Timeout)". The ACM judged the SCR temperature or conversion signal reading erratic or not plausible compared with other sensors or its own history. SCR closed loop control reached its limit, or timed out.· Lost messageLost messageCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting SCR temperature or conversion signal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the SCR temperature or conversion signal reading with a second reference such as a gauge or another sensor on the engine.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 520372 FMI 16Selective Catalyst Reduction Closed Loop Control at Maximum Limit
Detroit lists SPN 520372 FMI 16 as "Selective Catalyst Reduction Closed Loop Control at Maximum Limit". The ACM reports that the measured value itself is out of its normal range; the SCR temperature or conversion signal may be correct and a real condition may exist. SCR closed loop control reached its limit, or timed out.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the SCR temperature or conversion signal measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the SCR temperature or conversion signal.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Check the DEF quality and the dosing rate before blaming the catalyst.
- 2Read both NOx sensors in the diagnostic tool and compare inlet with outlet.
- 3Inspect the SCR temperature sensors and their connectors for damage.
- 4Check the exhaust for leaks between the turbo and the catalyst.
Causes
- Poor DEF quality or dosing
- NOx sensor error
- Catalyst damage
- Temperature sensor fault
Most common here: real condition (8 of 17)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: A check-engine lamp, a derate and in some cases the DEF inducement stages on the dash.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
