Detroit · Aftertreatment
Detroit Hydrocarbon doser and fuel cut-off valve fault codes
The hydrocarbon doser injects fuel into the exhaust for regeneration. Codes cover the doser valve, the doser fuel line pressure and the fuel cut-off valve.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 3471 FMI 3 to SPN 4077 FMI 14 are all about the hydrocarbon doser and fuel cut-off valve. The most common failure type is shorted high (5 of 21); none needs an immediate stop. Start with this check: inspect the doser valve connector and wiring for corrosion and damage.
How urgent are they?
None of the 21 codes here means stop now; all 21 can wait until the shift ends, but find the cause before the next one.
- Check soon21
What should I check first?
Inspect the doser valve connector and wiring for corrosion and damage.
Shared checks21 of 21
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 3471 FMI 3Hydrocarbon Electronic Dosing Valve Circuit Failed High
Detroit lists SPN 3471 FMI 3 as "Hydrocarbon Electronic Dosing Valve Circuit Failed High". The ACM found the HC doser circuit shorted high or reading above its limit, which usually means a short to battery on the output wire. The HC doser valve sprays fuel into the exhaust upstream of the DOC to heat it for regeneration.· Shorted highShorted highCheck soonCauses
- Output wire of the HC doser rubbed through and touching a live wire
- Internal short in the HC doser
Checks
- 1Unplug the HC doser and look for voltage on the output wire with the key on.
- 2Measure the HC doser winding resistance and compare it with a good unit.
- 3The HC doser valve circuit is shorted high; check the doser connector and its wire for a short to supply.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3471 FMI 4Hydrocarbon Doser Circuit Failed Low
Detroit lists SPN 3471 FMI 4 as "Hydrocarbon Doser Circuit Failed Low". The ACM found the HC doser circuit shorted low or reading below its limit, which usually means a short to ground. The HC doser valve sprays fuel into the exhaust upstream of the DOC to heat it for regeneration.· Shorted lowShorted lowCheck soonCauses
- Output wire of the HC doser rubbed through against the engine
- Internal short in the HC doser
Checks
- 1Unplug the HC doser and check the output wire for continuity to ground.
- 2Measure the HC doser winding resistance and look for a very low value.
- 3The HC doser circuit is shorted low; check the doser connector and its wire for a short to ground.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3471 FMI 5Hydrocarbon Doser Circuit Failed Open
Detroit lists SPN 3471 FMI 5 as "Hydrocarbon Doser Circuit Failed Open". The ACM found the HC doser circuit open, so no current flows when the output is switched on. The HC doser valve sprays fuel into the exhaust upstream of the DOC to heat it for regeneration.· Open circuitOpen circuitCheck soonCauses
- Open wire or pushed-out pin at the HC doser connector
- Burned-out HC doser coil
Checks
- 1Check continuity from the ACM pin to the HC doser connector and back.
- 2Measure the HC doser winding resistance; an open reading means the part has failed.
- 3The HC doser circuit is open; check the doser coil resistance and the wire for a break.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 3471 FMI 13Parameter Configuration for HC Dosing Monitoring Invalid
Detroit lists SPN 3471 FMI 13 as "Parameter Configuration for HC Dosing Monitoring Invalid". The ACM reports a condition on the HC doser that it could not clear on its own. The HC doser valve sprays fuel into the exhaust upstream of the DOC to heat it for regeneration.· Part or controllerPart or controllerCheck soonCauses
- Wiring, supply or mechanical problem on the HC doser
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the HC doser in the tool and watch the result.
- 3The HC dosing monitoring parameters are invalid; reload the ACM parameters with the tool.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 3471 FMI 14HC Dosing Inhibited By Level 2 Monitoring
Detroit lists SPN 3471 FMI 14 as "HC Dosing Inhibited By Level 2 Monitoring". The ACM reports a condition on the HC doser that it could not clear on its own. The HC doser valve sprays fuel into the exhaust upstream of the DOC to heat it for regeneration.· OtherOtherCheck soonCauses
- Wiring, supply or mechanical problem on the HC doser
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the HC doser in the tool and watch the result.
- 3HC dosing was blocked by the level 2 monitor; read the other codes, because this monitor reacts to a related fault.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 3480 FMI 1Doser Fuel Supply Pressure Abnormal
Detroit lists SPN 3480 FMI 1 as "Doser Fuel Supply Pressure Abnormal". The ACM reports a condition on the HC doser that it could not clear on its own. The doser fuel line pressure sensors check that fuel reaches the HC doser at the right pressure.· Real conditionReal conditionCheck soonCauses
- Wiring, supply or mechanical problem on the HC doser
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the HC doser in the tool and watch the result.
- 3The doser fuel supply pressure is abnormal; check the fuel supply to the doser for restrictions and air.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3480 FMI 2Hydrocarbon Doser Fuel Line Pressure Low
Detroit lists SPN 3480 FMI 2 as "Hydrocarbon Doser Fuel Line Pressure Low". The ACM reports a condition on the HC doser that it could not clear on its own. The doser fuel line pressure sensors check that fuel reaches the HC doser at the right pressure.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Wiring, supply or mechanical problem on the HC doser
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the HC doser in the tool and watch the result.
- 3The doser fuel line pressure is low; check the supply line and the doser for leaks and blockage.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3480 FMI 3Fuel Compensation Pressure Sensor Circuit Failed High
Same failure as SPN 3471 FMI 3 ("Hydrocarbon Electronic Dosing Valve Circuit Failed High") on a sibling part: Detroit lists SPN 3480 FMI 3 as "Fuel Compensation Pressure Sensor Circuit Failed High". The doser fuel line pressure sensors check that fuel reaches the HC doser at the right pressure.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 3471 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3471 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3480 FMI 4Fuel Compensation Pressure Sensor Circuit Failed Low
Same failure as SPN 3471 FMI 4 ("Hydrocarbon Doser Circuit Failed Low") on a sibling part: Detroit lists SPN 3480 FMI 4 as "Fuel Compensation Pressure Sensor Circuit Failed Low". The doser fuel line pressure sensors check that fuel reaches the HC doser at the right pressure.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3471 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3471 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3480 FMI 14Doser FLP Sensors Failed Self Test
Detroit lists SPN 3480 FMI 14 as "Doser FLP Sensors Failed Self Test". The ACM reports a condition on the HC doser that it could not clear on its own. The doser fuel line pressure sensors check that fuel reaches the HC doser at the right pressure.· OtherOtherCheck soonCauses
- Wiring, supply or mechanical problem on the HC doser
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the HC doser in the tool and watch the result.
- 3The doser fuel line pressure sensors failed their self-test; check the sensor connector and replace if needed.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 3480 FMI 21Fuel Cut-off Valve Pressure Not Plausible
Detroit lists SPN 3480 FMI 21 as "Fuel Cut-off Valve Pressure Not Plausible". The ACM reports a condition on the HC doser that it could not clear on its own. The doser fuel line pressure sensors check that fuel reaches the HC doser at the right pressure.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Wiring, supply or mechanical problem on the HC doser
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the HC doser in the tool and watch the result.
- 3The cut-off valve pressure is not plausible; check the valve operation and the pressure sensor.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3482 FMI 3Fuel Cut-off Valve Circuit Failed High
Same failure as SPN 3471 FMI 3 ("Hydrocarbon Electronic Dosing Valve Circuit Failed High") on a sibling part: Detroit lists SPN 3482 FMI 3 as "Fuel Cut-off Valve Circuit Failed High". The fuel cut-off valve shuts the fuel to the doser when it is not in use or on a fault.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 3471 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3471 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3482 FMI 4Fuel Cut-off Valve Circuit Failed Low
Same failure as SPN 3471 FMI 4 ("Hydrocarbon Doser Circuit Failed Low") on a sibling part: Detroit lists SPN 3482 FMI 4 as "Fuel Cut-off Valve Circuit Failed Low". The fuel cut-off valve shuts the fuel to the doser when it is not in use or on a fault.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3471 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3471 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3482 FMI 5Fuel Cut-off Valve Circuit Failed Open
Same failure as SPN 3471 FMI 5 ("Hydrocarbon Doser Circuit Failed Open") on a sibling part: Detroit lists SPN 3482 FMI 5 as "Fuel Cut-off Valve Circuit Failed Open". The fuel cut-off valve shuts the fuel to the doser when it is not in use or on a fault.· Open circuitOpen circuitCheck soonCauses
- The causes listed under SPN 3471 FMI 5, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3471 FMI 5, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 3490 FMI 3Post Run Indicator Lamp
Detroit lists SPN 3490 FMI 3 as "Post Run Indicator Lamp". The ACM found the HC doser circuit shorted high or reading above its limit, which usually means a short to battery on the output wire. The post run indicator lamp output warns the driver to leave the engine running or the key on while the system finishes after-run tasks.· Shorted highShorted highCheck soonCauses
- Output wire of the HC doser rubbed through and touching a live wire
- Internal short in the HC doser
Checks
- 1Unplug the HC doser and look for voltage on the output wire with the key on.
- 2Measure the HC doser winding resistance and compare it with a good unit.
- 3The post run lamp circuit is shorted or open; check the lamp output wire and the cluster.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3490 FMI 4Post Run Indicator Lamp
Same failure as SPN 3490 FMI 3 ("Post Run Indicator Lamp") on a sibling part: Detroit lists SPN 3490 FMI 4 as "Post Run Indicator Lamp". The post run indicator lamp output warns the driver to leave the engine running or the key on while the system finishes after-run tasks.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3490 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3490 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3490 FMI 5Post Run Indicator Lamp
Same failure as SPN 3490 FMI 3 ("Post Run Indicator Lamp") on a sibling part: Detroit lists SPN 3490 FMI 5 as "Post Run Indicator Lamp". The post run indicator lamp output warns the driver to leave the engine running or the key on while the system finishes after-run tasks.· Open circuitOpen circuitCheck soonCauses
- The causes listed under SPN 3490 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3490 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 4077 FMI 0High Doser Fuel Line Pressure
Detroit lists SPN 4077 FMI 0 as "High Doser Fuel Line Pressure". The ACM reports a condition on the HC doser that it could not clear on its own. The doser fuel line pressure is measured to detect leaks and blockages in the line to the HC doser.· Real conditionReal conditionCheck soonCauses
- Wiring, supply or mechanical problem on the HC doser
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the HC doser in the tool and watch the result.
- 3The doser fuel line pressure is high; check the line for a blockage and the cut-off valve.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4077 FMI 3Doser Fuel Line Pressure Sensor Circuit Failed High
Same failure as SPN 3471 FMI 3 ("Hydrocarbon Electronic Dosing Valve Circuit Failed High") on a sibling part: Detroit lists SPN 4077 FMI 3 as "Doser Fuel Line Pressure Sensor Circuit Failed High". The doser fuel line pressure is measured to detect leaks and blockages in the line to the HC doser.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 3471 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3471 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 4077 FMI 4Doser Fuel Line Pressure Sensor Circuit Failed Low
Same failure as SPN 3471 FMI 4 ("Hydrocarbon Doser Circuit Failed Low") on a sibling part: Detroit lists SPN 4077 FMI 4 as "Doser Fuel Line Pressure Sensor Circuit Failed Low". The doser fuel line pressure is measured to detect leaks and blockages in the line to the HC doser.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3471 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3471 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 4077 FMI 14Doser Fuel Line Pressure Failed Self-Test
Detroit lists SPN 4077 FMI 14 as "Doser Fuel Line Pressure Failed Self-Test". The ACM reports a condition on the HC doser that it could not clear on its own. The doser fuel line pressure is measured to detect leaks and blockages in the line to the HC doser.· OtherOtherCheck soonCauses
- Wiring, supply or mechanical problem on the HC doser
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the HC doser in the tool and watch the result.
- 3The doser fuel line pressure sensor failed the self-test; check its connector and replace it if needed.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Inspect the doser valve connector and wiring for corrosion and damage.
- 2Read the doser fuel line pressure in the diagnostic tool and watch it during the doser test.
- 3Check the fuel cut-off valve connector and its operation.
- 4Inspect the fuel supply to the doser for restriction, leaks and air.
Causes
- Doser valve fault
- Fuel line pressure fault
- Wiring fault
- Fuel supply restriction
Most common here: shorted high (5 of 21)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: Regenerations that fail or are not started, and a check-engine lamp on the dash.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
