EF Logo

Detroit · Air system

Detroit Exhaust manifold pressure sensors (P3) fault codes

The MCM measures exhaust manifold pressure on each bank. Detroit lists circuit faults, stuck-in-range and rationality checks, and drift of the exhaust pressure sensors.

FaultCheckSPN 3609FMI 2Detroit · Exhaust manifold pressure sensors (P3)
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.

What do these codes mean?

Detroit codes SPN 3609 FMI 2 to SPN 521141 FMI 4 are all about the exhaust manifold pressure sensors (P3). Most are erratic or implausible faults; none needs an immediate stop. Start with this check: check the exhaust pressure sensor tube for soot plugging and leaks.

How urgent are they?

None of the 15 codes here means stop now; all 15 can wait until the shift ends, but find the cause before the next one.

  • Check soon15

What should I check first?

Check the exhaust pressure sensor tube for soot plugging and leaks.

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Detroit SPN 3609 FMI 2Sensor Drift Fault for Second Exhaust Pressure

    Detroit lists SPN 3609 FMI 2 as "Sensor Drift Fault for Second Exhaust Pressure".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting exhaust pressure sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the exhaust pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 3609 FMI 12Pressure DPF Inlet Not Plausible

    Detroit lists SPN 3609 FMI 12 as "Pressure DPF Inlet Not Plausible".· Part or controller
    Check soon

    Causes

    • Signal path broken at the connector or the harness
    • Failed sensor or module

    Checks

    1. 1Check the connector and the power supply to the exhaust pressure sensor.
    2. 2Check the signal wire to the MCM for an open.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 6384 FMI 2Sensor Drift Fault for First Exhaust Pressure

    Same failure as SPN 3609 FMI 2 ("Sensor Drift Fault for Second Exhaust Pressure") on a sibling part: Detroit lists SPN 6384 FMI 2 as "Sensor Drift Fault for First Exhaust Pressure".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 3609 FMI 2, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3609 FMI 2, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 8619 FMI 11P3 Sensor 1 Stuck in Range Check High

    Detroit lists SPN 8619 FMI 11 as "P3 Sensor 1 Stuck in Range Check High".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting exhaust pressure sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the exhaust pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 8619 FMI 14P3 Sensor 1 Stuck in Range Check Low

    Detroit lists SPN 8619 FMI 14 as "P3 Sensor 1 Stuck in Range Check Low".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting exhaust pressure sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the exhaust pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 8619 FMI 20Engine Exhaust Manifold Absolute Pressure 1 Rationality (Low Box)

    Same failure as SPN 3609 FMI 12 ("Pressure DPF Inlet Not Plausible") on a sibling part: Detroit lists SPN 8619 FMI 20 as "Engine Exhaust Manifold Absolute Pressure 1 Rationality (Low Box)".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 3609 FMI 12, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3609 FMI 12, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 8619 FMI 21Engine Exhaust Manifold Absolute Pressure 1 Rationality (High Box)

    Same failure as SPN 3609 FMI 12 ("Pressure DPF Inlet Not Plausible") on a sibling part: Detroit lists SPN 8619 FMI 21 as "Engine Exhaust Manifold Absolute Pressure 1 Rationality (High Box)".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 3609 FMI 12, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3609 FMI 12, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 8620 FMI 11P3 Sensor 2 Stuck in Range Check High

    Same failure as SPN 8619 FMI 11 ("P3 Sensor 1 Stuck in Range Check High") on a sibling part: Detroit lists SPN 8620 FMI 11 as "P3 Sensor 2 Stuck in Range Check High".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 8619 FMI 11, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 8619 FMI 11, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 8620 FMI 14P3 Sensor 2 Stuck in Range Check Low

    Same failure as SPN 8619 FMI 14 ("P3 Sensor 1 Stuck in Range Check Low") on a sibling part: Detroit lists SPN 8620 FMI 14 as "P3 Sensor 2 Stuck in Range Check Low".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 8619 FMI 14, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 8619 FMI 14, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 8620 FMI 20Engine Exhaust Manifold Absolute Pressure 2 Rationality (Low Box)

    Same failure as SPN 3609 FMI 12 ("Pressure DPF Inlet Not Plausible") on a sibling part: Detroit lists SPN 8620 FMI 20 as "Engine Exhaust Manifold Absolute Pressure 2 Rationality (Low Box)".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 3609 FMI 12, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3609 FMI 12, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 8620 FMI 21Engine Exhaust Manifold Absolute Pressure 2 Rationality (High Box)

    Same failure as SPN 3609 FMI 12 ("Pressure DPF Inlet Not Plausible") on a sibling part: Detroit lists SPN 8620 FMI 21 as "Engine Exhaust Manifold Absolute Pressure 2 Rationality (High Box)".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 3609 FMI 12, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3609 FMI 12, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 521140 FMI 3Exhaust Manifold Pressure Sensor Bank 1 Circuit Failed High

    Detroit lists SPN 521140 FMI 3 as "Exhaust Manifold Pressure Sensor Bank 1 Circuit Failed High".· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V supply or open between the exhaust pressure sensor and the MCM
    • The exhaust pressure sensor has failed inside

    Checks

    1. 1Unplug the exhaust pressure sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
    2. 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 521140 FMI 4Exhaust Manifold Pressure Sensor Bank 1 Circuit Failed Low

    Detroit lists SPN 521140 FMI 4 as "Exhaust Manifold Pressure Sensor Bank 1 Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • Signal wire chafed against the engine and shorted to ground
    • The exhaust pressure sensor has failed inside or its supply wire is open

    Checks

    1. 1Unplug the exhaust pressure sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
    2. 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 521141 FMI 3Exhaust Manifold Pressure Sensor Bank 2 Circuit Failed High

    Same failure as SPN 521140 FMI 3 ("Exhaust Manifold Pressure Sensor Bank 1 Circuit Failed High") on a sibling part: Detroit lists SPN 521141 FMI 3 as "Exhaust Manifold Pressure Sensor Bank 2 Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 521140 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 521140 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 521141 FMI 4Exhaust Manifold Pressure Bank 2 Sensor Circuit Failed Low

    Same failure as SPN 521140 FMI 4 ("Exhaust Manifold Pressure Sensor Bank 1 Circuit Failed Low") on a sibling part: Detroit lists SPN 521141 FMI 4 as "Exhaust Manifold Pressure Bank 2 Sensor Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 521140 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 521140 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Check the exhaust pressure sensor tube for soot plugging and leaks.
  2. 2Inspect the connector and wiring for heat damage and chafing.
  3. 3Compare the reading with the ambient pressure with the engine off.
  4. 4Look for exhaust leaks at the manifold and the turbo.

Causes

  • Plugged or leaking exhaust pressure sensor line
  • Sensor connector or harness damage
  • Sensor drift or a stuck-in-range sensor
  • Exhaust restriction or a leak at the manifold

Most codes here: erratic or implausible (10 of 15)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: A loss of power, turbo or EGR control faults and a check-engine lamp.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.