Detroit · Aftertreatment
Detroit DOC and DPF temperature sensors fault codes
Temperature sensors at the DOC inlet, DOC outlet and DPF outlet let the ACM control regeneration. Detroit logs circuit, plausibility and drift faults and DOC efficiency.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 3242 FMI 3 to SPN 520381 FMI 2 are all about the dOC and DPF temperature sensors. The most common failure type is erratic or implausible (10 of 27); 2 need an immediate stop. Start with this check: compare the DOC inlet, DOC outlet and DPF outlet temperatures in the tool on a cold engine; they should be close.
How urgent are they?
2 of 27 codes here mean stop now; the other 25 can wait until the shift ends, but find the cause before the next one.
- Stop now2
- Check soon25
What should I check first?
Compare the DOC inlet, DOC outlet and DPF outlet temperatures in the tool on a cold engine; they should be close.
Shared checks27 of 27
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 3242 FMI 3Diesel Oxidation Catalyst Inlet Temperature Sensor Circuit Failed High
Detroit lists SPN 3242 FMI 3 as "Diesel Oxidation Catalyst Inlet Temperature Sensor Circuit Failed High". The ACM saw the exhaust temperature sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The DOC inlet temperature sensor shows the exhaust heat entering the oxidation catalyst and decides when HC dosing may start.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the exhaust temperature sensor and the ACM
- The exhaust temperature sensor has failed inside
Checks
- 1Unplug the exhaust temperature sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
- 3The DOC inlet temperature sensor reads high; unplug it and check its signal wire for a short to supply.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3242 FMI 4Diesel Oxidation Catalyst Inlet Temperature Sensor Failed Low
Detroit lists SPN 3242 FMI 4 as "Diesel Oxidation Catalyst Inlet Temperature Sensor Failed Low". The ACM saw the exhaust temperature sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The DOC inlet temperature sensor shows the exhaust heat entering the oxidation catalyst and decides when HC dosing may start.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The exhaust temperature sensor has failed inside or its supply wire is open
Checks
- 1Unplug the exhaust temperature sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the ACM if it is missing.
- 3The DOC inlet temperature sensor reads low; check its signal wire for a short to ground.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3242 FMI 8Diesel Oxidation Catalyst Inlet Temperature - Signal Spike
Detroit lists SPN 3242 FMI 8 as "Diesel Oxidation Catalyst Inlet Temperature - Signal Spike". The ACM judged the exhaust temperature sensor reading erratic or not plausible compared with other sensors or its own history. The DOC inlet temperature sensor shows the exhaust heat entering the oxidation catalyst and decides when HC dosing may start.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting exhaust temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the exhaust temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
- 3The DOC inlet temperature spikes; check the connector for intermittent contact and the wire for chafing.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3242 FMI 17Diesel Oxidation Catalyst Inlet Temperature Out Of Range Low Preventing HC Dosing
Detroit lists SPN 3242 FMI 17 as "Diesel Oxidation Catalyst Inlet Temperature Out Of Range Low Preventing HC Dosing". The ACM reports that the measured value itself is out of its normal range; the exhaust temperature sensor may be correct and a real condition may exist. The DOC inlet temperature sensor shows the exhaust heat entering the oxidation catalyst and decides when HC dosing may start.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the exhaust temperature sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the exhaust temperature sensor.
- 2Check the system for the condition the code describes and fix it first.
- 3The DOC inlet is too cold to allow HC dosing; check the exhaust temperature path, the turbo outlet and the sensor.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3242 FMI 18Diesel Oxidation Catalyst Inlet Temperature Out Of Range Low Preventing HC Dosing
Same failure as SPN 3242 FMI 17 ("Diesel Oxidation Catalyst Inlet Temperature Out Of Range Low Preventing HC Dosing") on a sibling part: Detroit lists SPN 3242 FMI 18 as "Diesel Oxidation Catalyst Inlet Temperature Out Of Range Low Preventing HC Dosing". The DOC inlet temperature sensor shows the exhaust heat entering the oxidation catalyst and decides when HC dosing may start.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 3242 FMI 17, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3242 FMI 17, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3242 FMI 20Diesel Oxidation Catalyst Temperature Drift - Inlet High or Outlet Low
Detroit lists SPN 3242 FMI 20 as "Diesel Oxidation Catalyst Temperature Drift - Inlet High or Outlet Low". The ACM found the exhaust temperature sensor value drifted away from what the engine state says it should be. The DOC inlet temperature sensor shows the exhaust heat entering the oxidation catalyst and decides when HC dosing may start.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the exhaust temperature sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the exhaust temperature sensor for leaks, restrictions or contamination.
- 3The DOC inlet reads higher than the outlet; compare the two sensors and check which one is drifting.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3246 FMI 0Diesel Particulate Filter Outlet Temperature - Very High
The ACM measured the DPF outlet temperature very high. This protects the filter and the catalyst from overheating, so it can cause an immediate derate.· Real conditionReal conditionStop nowCauses
- Uncontrolled regeneration or a fuel leak into the exhaust
- Failed doser leaking fuel
- Soot-loaded filter burning too hot
- Temperature sensor reading too high
Checks
- 1Look for exhaust smoke, hot spots and signs of overheating around the DPF housing.
- 2Check the HC doser and its fuel cut-off valve for leaking fuel into the exhaust.
- 3Read the DPF outlet temperature against the DOC outlet temperature in the tool while idling.
- 4Inspect the temperature sensor and its wiring before replacing any exhaust part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3246 FMI 2DPF Outlet Temperature Not Plausible
Detroit lists SPN 3246 FMI 2 as "DPF Outlet Temperature Not Plausible". The ACM judged the exhaust temperature sensor reading erratic or not plausible compared with other sensors or its own history. The DPF outlet temperature sensor shows the heat leaving the filter and protects it during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting exhaust temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the exhaust temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
- 3The DPF outlet reading does not match the DOC; compare the two sensors on a cold engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3246 FMI 3Diesel Particulate Filter Outlet Temperature Sensor Circuit Failed High
Same failure as SPN 3242 FMI 3 ("Diesel Oxidation Catalyst Inlet Temperature Sensor Circuit Failed High") on a sibling part: Detroit lists SPN 3246 FMI 3 as "Diesel Particulate Filter Outlet Temperature Sensor Circuit Failed High". The DPF outlet temperature sensor shows the heat leaving the filter and protects it during regeneration.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 3242 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3242 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3246 FMI 4Diesel Particulate Filter Outlet Temperature Sensor Circuit Failed Low
Same failure as SPN 3242 FMI 4 ("Diesel Oxidation Catalyst Inlet Temperature Sensor Failed Low") on a sibling part: Detroit lists SPN 3246 FMI 4 as "Diesel Particulate Filter Outlet Temperature Sensor Circuit Failed Low". The DPF outlet temperature sensor shows the heat leaving the filter and protects it during regeneration.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3242 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3242 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3246 FMI 8Diesel Particulate Filter Outlet Temperature - Signal Spike
Detroit lists SPN 3246 FMI 8 as "Diesel Particulate Filter Outlet Temperature - Signal Spike". The ACM judged the exhaust temperature sensor reading erratic or not plausible compared with other sensors or its own history. The DPF outlet temperature sensor shows the heat leaving the filter and protects it during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting exhaust temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the exhaust temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
- 3The DPF outlet temperature spikes; check the sensor connector and wire for intermittent contact.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3246 FMI 15Diesel Particulate Filter Outlet Temperature - High
Detroit lists SPN 3246 FMI 15 as "Diesel Particulate Filter Outlet Temperature - High". The ACM reports that the measured value itself is out of its normal range; the exhaust temperature sensor may be correct and a real condition may exist. The DPF outlet temperature sensor shows the heat leaving the filter and protects it during regeneration.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the exhaust temperature sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the exhaust temperature sensor.
- 2Check the system for the condition the code describes and fix it first.
- 3The DPF outlet is high but not extreme; check the regeneration state and the DOC temperature.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3246 FMI 20Diesel Particulate Filter Outlet Temperature Sensor Stuck
Detroit lists SPN 3246 FMI 20 as "Diesel Particulate Filter Outlet Temperature Sensor Stuck". The ACM found the exhaust temperature sensor value drifted away from what the engine state says it should be. The DPF outlet temperature sensor shows the heat leaving the filter and protects it during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the exhaust temperature sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the exhaust temperature sensor for leaks, restrictions or contamination.
- 3The DPF outlet sensor is stuck; compare it with the other exhaust sensors while the engine warms up.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3246 FMI 21Diesel Particulate Filter Outlet Temperature Sensor - Not Plausible
Same failure as SPN 3246 FMI 2 ("DPF Outlet Temperature Not Plausible") on a sibling part: Detroit lists SPN 3246 FMI 21 as "Diesel Particulate Filter Outlet Temperature Sensor - Not Plausible". The DPF outlet temperature sensor shows the heat leaving the filter and protects it during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 3246 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3246 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3250 FMI 0Diesel Oxidation Catalyst Outlet Temperature Very High
Detroit lists SPN 3250 FMI 0 as "Diesel Oxidation Catalyst Outlet Temperature Very High". The ACM reports that the measured value itself is out of its normal range; the exhaust temperature sensor may be correct and a real condition may exist. The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Real conditionReal conditionStop nowCauses
- A real fault in the system the exhaust temperature sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the exhaust temperature sensor.
- 2Check the system for the condition the code describes and fix it first.
- 3The DOC outlet is very hot; stop the regeneration and check the HC doser for leaks.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3250 FMI 2DOC Outlet Temperature Not Plausible
Same failure as SPN 3246 FMI 2 ("DPF Outlet Temperature Not Plausible") on a sibling part: Detroit lists SPN 3250 FMI 2 as "DOC Outlet Temperature Not Plausible". The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 3246 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3246 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3250 FMI 3Diesel Oxidation Catalyst Outlet Temperature Sensor Circuit Failed High
Same failure as SPN 3242 FMI 3 ("Diesel Oxidation Catalyst Inlet Temperature Sensor Circuit Failed High") on a sibling part: Detroit lists SPN 3250 FMI 3 as "Diesel Oxidation Catalyst Outlet Temperature Sensor Circuit Failed High". The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 3242 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3242 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3250 FMI 4Diesel Oxidation Catalyst Outlet Temperature Circuit Failed Low
Same failure as SPN 3242 FMI 4 ("Diesel Oxidation Catalyst Inlet Temperature Sensor Failed Low") on a sibling part: Detroit lists SPN 3250 FMI 4 as "Diesel Oxidation Catalyst Outlet Temperature Circuit Failed Low". The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3242 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3242 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3250 FMI 7Diesel Oxidation Catalyst Outlet Temperature Response Error
Detroit lists SPN 3250 FMI 7 as "Diesel Oxidation Catalyst Outlet Temperature Response Error". The ACM judged the exhaust temperature sensor reading erratic or not plausible compared with other sensors or its own history. The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Part or controllerPart or controllerCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting exhaust temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the exhaust temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
- 3The DOC outlet temperature does not respond to the dosing; check the doser and the sensor response.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 3250 FMI 8Diesel Oxidation Catalyst Outlet Temperature - Signal Spike
Detroit lists SPN 3250 FMI 8 as "Diesel Oxidation Catalyst Outlet Temperature - Signal Spike". The ACM judged the exhaust temperature sensor reading erratic or not plausible compared with other sensors or its own history. The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting exhaust temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the exhaust temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
- 3The DOC outlet temperature spikes; check the sensor connector and wire for intermittent contact.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3250 FMI 15Diesel Oxidation Catalyst Outlet Temperature High
Detroit lists SPN 3250 FMI 15 as "Diesel Oxidation Catalyst Outlet Temperature High". The ACM reports that the measured value itself is out of its normal range; the exhaust temperature sensor may be correct and a real condition may exist. The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the exhaust temperature sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the exhaust temperature sensor.
- 2Check the system for the condition the code describes and fix it first.
- 3The DOC outlet is high; check the doser output and the regeneration control.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3250 FMI 20Diesel Oxidation Catalyst Temperature Drift - Inlet Low or Outlet High
Same failure as SPN 3242 FMI 20 ("Diesel Oxidation Catalyst Temperature Drift - Inlet High or Outlet Low") on a sibling part: Detroit lists SPN 3250 FMI 20 as "Diesel Oxidation Catalyst Temperature Drift - Inlet Low or Outlet High". The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 3242 FMI 20, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3242 FMI 20, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3250 FMI 31Abnormal Diesel Oxidation Catalyst Temperature Rise
Detroit lists SPN 3250 FMI 31 as "Abnormal Diesel Oxidation Catalyst Temperature Rise". The ACM logged a condition on the exhaust temperature sensor; the title says what it measured. The DOC outlet temperature sensor shows the heat the catalyst has made from the dosed fuel and is a key regeneration signal.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the exhaust temperature sensor watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
- 3An abnormal temperature rise across the DOC suggests unburned fuel; check the doser and the DOC.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4332 FMI 31DOC Inlet Temperature Out of Range Low Preventing Dosing
Detroit lists SPN 4332 FMI 31 as "DOC Inlet Temperature Out of Range Low Preventing Dosing". The ACM logged a condition on the exhaust temperature sensor; the title says what it measured. The DOC inlet temperature is too low for dosing, so regeneration cannot start.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the exhaust temperature sensor watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
- 3The DOC inlet temperature is too low for dosing; check the exhaust temperature path and the sensor.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 5018 FMI 18Diesel Oxidation Catalyst Efficiency Fault
The ACM found the diesel oxidation catalyst (DOC) converting less than expected. A weak DOC cannot raise the exhaust temperature for regeneration.· Real conditionReal conditionCheck soonCauses
- DOC contaminated or aged
- HC doser not delivering fuel
- Exhaust temperature sensor error
Checks
- 1Check the DOC inlet and outlet temperatures in the tool during a parked regeneration.
- 2Check the HC doser operation and its fuel supply.
- 3Inspect the exhaust temperature sensors and their wiring for faults.
- 4Inspect the DOC for soot, fuel soaking or physical damage.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520378 FMI 0Aftertreatment Temperature Not Plausible
Same failure as SPN 3246 FMI 2 ("DPF Outlet Temperature Not Plausible") on a sibling part: Detroit lists SPN 520378 FMI 0 as "Aftertreatment Temperature Not Plausible". Aftertreatment temperature values do not agree with each other.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 3246 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3246 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520381 FMI 2DOC Inlet Temperature Not Plausible
Same failure as SPN 3246 FMI 2 ("DPF Outlet Temperature Not Plausible") on a sibling part: Detroit lists SPN 520381 FMI 2 as "DOC Inlet Temperature Not Plausible". The DOC inlet temperature does not agree with the other exhaust temperatures.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 3246 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3246 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Compare the DOC inlet, DOC outlet and DPF outlet temperatures in the tool on a cold engine; they should be close.
- 2Inspect the temperature sensor connectors for heat damage and corrosion.
- 3Check the wiring between the sensors and the ACM for chafing and shorts.
- 4Check the DOC for melting, cracking or fuel soaking when an efficiency code is set.
Causes
- Exhaust temperature sensor failure
- Wiring or connector damage
- DOC damage
- Exhaust leak
Most common here: erratic or implausible (10 of 27)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: A check-engine lamp, regenerations that do not complete properly and a possible power derate.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
