EF Logo

Detroit · Aftertreatment

Detroit DEF tank level, temperature and quality fault codes

The DEF tank has a level and temperature sensor and a quality sensor. The ACM logs level, temperature, quality and inducement conditions.

FaultCheckSPN 5841FMI 14Detroit · DEF tank level, temperature and quality
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.

What do these codes mean?

Detroit codes SPN 1761 FMI 2 to SPN 521052 FMI 31 are all about the dEF tank level, temperature and quality. The most common failure type is erratic or implausible (8 of 25); 2 need an immediate stop. Start with this check: check the DEF level and fill the tank with fresh, clean fluid if it is low or suspect.

How urgent are they?

2 of 25 codes here mean stop now; the other 23 can wait until the shift ends, but find the cause before the next one.

  • Stop now2
  • Check soon23

What should I check first?

Check the DEF level and fill the tank with fresh, clean fluid if it is low or suspect.

Shared checks

25 of 25

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Detroit SPN 1761 FMI 2Diesel Exhaust Fluid (DEF) Tank Level Sensor Circuit Data Erratic, Intermittent or Incorrect

    Detroit lists SPN 1761 FMI 2 as "Diesel Exhaust Fluid (DEF) Tank Level Sensor Circuit Data Erratic, Intermittent or Incorrect".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting DEF tank sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the DEF tank sensor reading with a second reference such as a gauge or another sensor on the engine.
    3. 3Compare the tank level reading in the tool with the real fluid level and look for jumping values from a loose connector.
    4. 4Erratic level data: check the connector for loose pins and the level sensor float for sticking.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 1761 FMI 3Diesel Exhaust Fluid Tank Level Sensor Circuit Failed High

    Detroit lists SPN 1761 FMI 3 as "Diesel Exhaust Fluid Tank Level Sensor Circuit Failed High".· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V supply or open between the DEF tank sensor and the ACM
    • The DEF tank sensor has failed inside

    Checks

    1. 1Unplug the DEF tank sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
    2. 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
    3. 3Unplug the tank level sensor and look for a signal at the supply; check the sensor wire for a short to a positive wire.
    4. 4Level circuit high: check the sensor wire for a short to supply.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 1761 FMI 4Diesel Exhaust Fluid Tank Level Sensor Circuit Failed Low

    Detroit lists SPN 1761 FMI 4 as "Diesel Exhaust Fluid Tank Level Sensor Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • Signal wire chafed against the engine and shorted to ground
    • The DEF tank sensor has failed inside or its supply wire is open

    Checks

    1. 1Unplug the DEF tank sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
    2. 2Check the sensor supply at the connector with the key on and trace it back to the ACM if it is missing.
    3. 3Check the tank level sensor wire for a short to ground and the connector for water, which lowers the reading.
    4. 4Level circuit low: check the sensor wire for a short to ground and the connector for water.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 1761 FMI 18Diesel Exhaust Fluid (DEF) Tank Level 1 Condition - Empty Tank

    Detroit lists SPN 1761 FMI 18 as "Diesel Exhaust Fluid (DEF) Tank Level 1 Condition - Empty Tank".· Real condition
    Stop now

    Causes

    • A real fault in the system the DEF tank sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the DEF tank sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    3. 3The tank is nearly empty by the sensor reading; fill it with DEF and see whether the level comes back to normal.
    4. 4The tank reads empty; refill and check that the level recovers.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 1761 FMI 31Diesel Exhaust Fluid (DEF) Tank Level 3 Condition - Tank Level Very Low

    Detroit lists SPN 1761 FMI 31 as "Diesel Exhaust Fluid (DEF) Tank Level 3 Condition - Tank Level Very Low".· Real condition
    Stop now

    Causes

    • A real fault in the system the DEF tank sensor watches
    • Sensor or wiring fault

    Checks

    1. 1Read the live value and compare it with a reference.
    2. 2Check the connector and wiring.
    3. 3The level is very low; refill the tank, and if the level stays low after filling, test the level sensor.
    4. 4The tank level is very low; refill, and test the sensor if the level stays low.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 3031 FMI 3Diesel Exhaust Fluid Tank Temperature Sensor Circuit Failed High

    Same failure as SPN 1761 FMI 3 ("Diesel Exhaust Fluid Tank Level Sensor Circuit Failed High") on a sibling part: Detroit lists SPN 3031 FMI 3 as "Diesel Exhaust Fluid Tank Temperature Sensor Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 1761 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1761 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 3031 FMI 4Diesel Exhaust Fluid Tank Temperature Sensor Circuit Failed Low

    Same failure as SPN 1761 FMI 4 ("Diesel Exhaust Fluid Tank Level Sensor Circuit Failed Low") on a sibling part: Detroit lists SPN 3031 FMI 4 as "Diesel Exhaust Fluid Tank Temperature Sensor Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 1761 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1761 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 3031 FMI 10Diesel Exhaust Fluid Tank Temperature Erratic

    Detroit lists SPN 3031 FMI 10 as "Diesel Exhaust Fluid Tank Temperature Erratic".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting DEF tank sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the DEF tank sensor reading with a second reference such as a gauge or another sensor on the engine.
    3. 3Compare the DEF tank temperature with ambient and the coolant temperature; an erratic value suggests a loose sensor connector.
    4. 4The tank temperature is erratic; check the sensor connector and the tank heating.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 3515 FMI 2DEF quality sensor temperature rationality check fail

    Detroit lists SPN 3515 FMI 2 as "DEF quality sensor temperature rationality check fail".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting DEF tank sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the DEF tank sensor reading with a second reference such as a gauge or another sensor on the engine.
    3. 3The DEF quality sensor temperature does not match the tank temperature; compare the two values.
    4. 4The quality sensor temperature fails its check against the tank temperature; compare the two readings.
    5. 5The quality sensor reports a fluid temperature that must agree with the tank sensor; after a cold soak the two should be close, so compare them before the first start.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 3515 FMI 14DEF quality sensor temperature error

    Detroit lists SPN 3515 FMI 14 as "DEF quality sensor temperature error".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting DEF tank sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the DEF tank sensor reading with a second reference such as a gauge or another sensor on the engine.
    3. 3The DEF quality sensor temperature reading is in error; check the sensor connector and replace it if needed.
    4. 4The quality sensor temperature error; replace the sensor if the connector is good.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 3515 FMI 15DEF quality sensor temperature internal deviation too high

    Detroit lists SPN 3515 FMI 15 as "DEF quality sensor temperature internal deviation too high".· Real condition
    Check soon

    Causes

    • A real fault in the system the DEF tank sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the DEF tank sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    3. 3The DEF quality sensor temperature deviates from the internal model; compare it with the tank temperature.
    4. 4The quality sensor temperature deviates internally; replace the sensor.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 3516 FMI 1DEF Quality Sensor Percent Low

    Detroit lists SPN 3516 FMI 1 as "DEF Quality Sensor Percent Low".· Real condition
    Check soon

    Causes

    • A real fault in the system the DEF tank sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the DEF tank sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    3. 3The DEF quality sensor reports a low percentage; test the fluid with a refractometer.
    4. 4Low quality percent: test the fluid and refill if it is diluted.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 3516 FMI 3Diesel-Exhaust-Fluid Quality Sensor Open Load

    Detroit lists SPN 3516 FMI 3 as "Diesel-Exhaust-Fluid Quality Sensor Open Load".· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V supply or open between the DEF tank sensor and the ACM
    • The DEF tank sensor has failed inside

    Checks

    1. 1Unplug the DEF tank sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
    2. 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
    3. 3The DEF quality sensor circuit is open; check the connector and wires for a break.
    4. 4Open load: check the sensor connector and wires.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 3516 FMI 4DEF Quality Sensor Short Circuit

    Detroit lists SPN 3516 FMI 4 as "DEF Quality Sensor Short Circuit".· Shorted low
    Check soon

    Causes

    • Signal wire chafed against the engine and shorted to ground
    • The DEF tank sensor has failed inside or its supply wire is open

    Checks

    1. 1Unplug the DEF tank sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
    2. 2Check the sensor supply at the connector with the key on and trace it back to the ACM if it is missing.
    3. 3The DEF quality sensor circuit is shorted; check its wires for a short to ground.
    4. 4Short circuit: check the sensor wires for a short.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 3516 FMI 11Diesel-Exhaust-Fuel quality sensor internal error

    Detroit lists SPN 3516 FMI 11 as "Diesel-Exhaust-Fuel quality sensor internal error".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting DEF tank sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the DEF tank sensor reading with a second reference such as a gauge or another sensor on the engine.
    3. 3The DEF quality sensor reports an internal error; replace the sensor if the wiring is good.
    4. 4Internal error: replace the quality sensor.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 3516 FMI 12DEF quality sensor stuck

    Detroit lists SPN 3516 FMI 12 as "DEF quality sensor stuck".· Part or controller
    Check soon

    Causes

    • Signal path broken at the connector or the harness
    • Failed sensor or module

    Checks

    1. 1Check the connector and the power supply to the DEF tank sensor.
    2. 2Check the signal wire to the ACM for an open.
    3. 3The DEF quality sensor value is stuck; check the sensor after refilling with fresh DEF.
    4. 4Stuck value: refill with fresh DEF and see whether the value moves.
    5. 5A stuck quality value happens when the sensor cell is fouled or the fluid is stagnant; after fresh DEF circulates, the reading should move within a few minutes.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 3516 FMI 13DEF Quality Sensor CAN Signal Missing

    Detroit lists SPN 3516 FMI 13 as "DEF Quality Sensor CAN Signal Missing".· Part or controller
    Check soon

    Causes

    • Sensor aged, contaminated or out of calibration
    • A real fault in the system being measured

    Checks

    1. 1Compare the DEF tank sensor reading with a reference gauge or thermometer with the engine off and cold.
    2. 2Check the system around the DEF tank sensor for leaks, restrictions or contamination.
    3. 3The DEF quality sensor CAN signal is missing; check the sensor supply and the CAN wires.
    4. 4CAN signal missing: check the sensor supply and CAN wires.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 3516 FMI 20Diesel Exhaust Fluid Quality Concentration Data Drifted High

    Detroit lists SPN 3516 FMI 20 as "Diesel Exhaust Fluid Quality Concentration Data Drifted High".· Erratic or implausible
    Check soon

    Causes

    • Sensor aged, contaminated or out of calibration
    • A real fault in the system being measured

    Checks

    1. 1Compare the DEF tank sensor reading with a reference gauge or thermometer with the engine off and cold.
    2. 2Check the system around the DEF tank sensor for leaks, restrictions or contamination.
    3. 3The DEF quality drifted high; test the fluid and replace the sensor if the fluid is fine.
    4. 4Drifted high: test the fluid and recalibrate or replace the sensor.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 3516 FMI 21Diesel Exhaust Fluid Quality Concentration Data Drifted Low

    Detroit lists SPN 3516 FMI 21 as "Diesel Exhaust Fluid Quality Concentration Data Drifted Low".· Erratic or implausible
    Check soon

    Causes

    • Sensor aged, contaminated or out of calibration
    • A real fault in the system being measured

    Checks

    1. 1Compare the DEF tank sensor reading with a reference gauge or thermometer with the engine off and cold.
    2. 2Check the system around the DEF tank sensor for leaks, restrictions or contamination.
    3. 3The DEF quality drifted low; test the fluid and refill if it is diluted.
    4. 4Drifted low: test the fluid and refill if diluted.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 3517 FMI 4DEF quality sensor level short circuit

    Detroit lists SPN 3517 FMI 4 as "DEF quality sensor level short circuit".· Shorted low
    Check soon

    Causes

    • Signal wire chafed against the engine and shorted to ground
    • The DEF tank sensor has failed inside or its supply wire is open

    Checks

    1. 1Unplug the DEF tank sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
    2. 2Check the sensor supply at the connector with the key on and trace it back to the ACM if it is missing.
    3. 3The DEF quality sensor level channel is shorted; check its wire for a short to ground.
    4. 4The level channel is shorted; check its wire.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 5841 FMI 14Diesel Exhaust Fluid Quality Low

    The ACM judged the DEF concentration too low.· Lost message
    Check soon

    Causes

    • Diluted or wrong DEF in the tank
    • DEF quality sensor faulty
    • Contaminated DEF from a dirty container

    Checks

    1. 1Test the DEF concentration with a refractometer and note the reading.
    2. 2Drain and refill the DEF tank with fresh fluid if the concentration is out of range.
    3. 3Inspect the quality sensor connector for moisture and corrosion.
    4. 4Read the quality value in the tool after the refill and a short drive.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 521049 FMI 31DEF Inducement DEF Lamp Active

    Detroit lists SPN 521049 FMI 31 as "DEF Inducement DEF Lamp Active".· Real condition
    Check soon

    Causes

    • A real fault in the system the DEF tank sensor watches
    • Sensor or wiring fault

    Checks

    1. 1Read the live value and compare it with a reference.
    2. 2Check the connector and wiring.
    3. 3The DEF inducement lamp stage is active; fix the DEF fault behind it.
    4. 4The DEF lamp inducement stage is active; fix the DEF fault behind it, because the stage will not clear until it is cured.
    5. 5Inducement stages escalate with time and distance, so note the current stage, because the repair must be completed before the stage can be cleared by the tool.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 521050 FMI 14PTConf Error: No Response from MCM for Requests

    Detroit lists SPN 521050 FMI 14 as "PTConf Error: No Response from MCM for Requests".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting DEF tank sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the DEF tank sensor reading with a second reference such as a gauge or another sensor on the engine.
    3. 3The PTConf has no response from the MCM; check the CAN link to the MCM.
    4. 4PTConf got no reply from the MCM; check the MCM CAN link.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 521050 FMI 31DEF Inducement SEL Lamp Active

    Same failure as SPN 521049 FMI 31 ("DEF Inducement DEF Lamp Active") on a sibling part: Detroit lists SPN 521050 FMI 31 as "DEF Inducement SEL Lamp Active".· Real condition
    Check soon

    Causes

    • The causes listed under SPN 521049 FMI 31, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 521049 FMI 31, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 521052 FMI 31DEF Inducement CEL Lamp Active

    Same failure as SPN 521049 FMI 31 ("DEF Inducement DEF Lamp Active") on a sibling part: Detroit lists SPN 521052 FMI 31 as "DEF Inducement CEL Lamp Active".· Real condition
    Check soon

    Causes

    • The causes listed under SPN 521049 FMI 31, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 521049 FMI 31, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Check the DEF level and fill the tank with fresh, clean fluid if it is low or suspect.
  2. 2Test the DEF concentration with a refractometer to confirm the quality.
  3. 3Inspect the tank unit connector for moisture and bent pins.
  4. 4Read the level, temperature and quality values in the diagnostic tool.

Causes

  • DEF tank empty or diluted DEF
  • Level or quality sensor failure
  • Connector or wiring damage
  • Wrong fluid in the tank

Most common here: erratic or implausible (8 of 25)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: DEF level or quality lamps on the dash, and a staged power derate if the fault is ignored.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.