EF Logo

Detroit · Aftertreatment

Detroit DEF line heaters and doser heater fault codes

Heaters keep the DEF lines and the doser from freezing. The codes name each line heater, the doser diffuser heater and the coolant valve and their circuits.

FaultCheckSPN 3363FMI 0Detroit · Diesel Exhaust Fluid Tank Temperature
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.

What do these codes mean?

Detroit codes SPN 3363 FMI 0 to SPN 520383 FMI 10 are all about the dEF line heaters and doser heater. The most common failure type is shorted high (7 of 25); none needs an immediate stop. Start with this check: measure the heater element resistance and compare it with the other line heaters on the same truck.

How urgent are they?

None of the 25 codes here means stop now; all 25 can wait until the shift ends, but find the cause before the next one.

  • Check soon25

What should I check first?

Measure the heater element resistance and compare it with the other line heaters on the same truck.

Shared checks

25 of 25

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Detroit SPN 3363 FMI 0Diesel Exhaust Fluid Tank Temperature - High

    Detroit lists SPN 3363 FMI 0 as "Diesel Exhaust Fluid Tank Temperature - High".· Real condition
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the DEF heater
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the DEF heater in the tool and watch the result.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 3363 FMI 1Diesel Exhaust Fluid Tank Temperature - Low

    Detroit lists SPN 3363 FMI 1 as "Diesel Exhaust Fluid Tank Temperature - Low".· Real condition
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the DEF heater
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the DEF heater in the tool and watch the result.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 3363 FMI 3Diesel Exhaust Fluid Coolant Valve Circuit Failed High

    Detroit lists SPN 3363 FMI 3 as "Diesel Exhaust Fluid Coolant Valve Circuit Failed High".· Shorted high
    Check soon

    Causes

    • A short to the supply in the heater harness or connector
    • Failed heater element

    Checks

    1. 1Measure the heater element resistance at the connector with the heater unplugged and compare it with the others on the same line.
    2. 2Check the heater circuit wires for a short to battery between the connector and the ACM.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 3363 FMI 4Diesel Exhaust Fluid Valve Circuit Failed Low

    Detroit lists SPN 3363 FMI 4 as "Diesel Exhaust Fluid Valve Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • A short to ground in the heater harness or connector
    • Failed heater element

    Checks

    1. 1Measure the heater element resistance at the connector with the heater unplugged and compare it with the others on the same line.
    2. 2Check the heater circuit wires for a short to ground between the connector and the ACM.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 3363 FMI 5Diesel Exhaust Fluid Coolant Valve Circuit Failed Open

    Detroit lists SPN 3363 FMI 5 as "Diesel Exhaust Fluid Coolant Valve Circuit Failed Open".· Open circuit
    Check soon

    Causes

    • A broken wire in the heater harness or connector
    • Failed heater element

    Checks

    1. 1Measure the heater element resistance at the connector with the heater unplugged and compare it with the others on the same line.
    2. 2Check the heater circuit wires for a break or a pushed-out pin between the connector and the ACM.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 4353 FMI 3Diesel Exhaust Fluid (DEF) Doser Valve Diffuser Heater Circuit Failed High

    Same failure as SPN 3363 FMI 3 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed High") on a sibling part: Detroit lists SPN 4353 FMI 3 as "Diesel Exhaust Fluid (DEF) Doser Valve Diffuser Heater Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 4353 FMI 4Diffuser Heater Circuit Failed Low

    Same failure as SPN 3363 FMI 4 ("Diesel Exhaust Fluid Valve Circuit Failed Low") on a sibling part: Detroit lists SPN 4353 FMI 4 as "Diffuser Heater Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 4353 FMI 5Diffuser Heater Open Circuit

    Same failure as SPN 3363 FMI 5 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed Open") on a sibling part: Detroit lists SPN 4353 FMI 5 as "Diffuser Heater Open Circuit".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 4354 FMI 3Line Heater #1 Circuit Failed High

    Same failure as SPN 3363 FMI 3 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed High") on a sibling part: Detroit lists SPN 4354 FMI 3 as "Line Heater #1 Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 4354 FMI 4Line Heater #1 Circuit Failed Low

    Same failure as SPN 3363 FMI 4 ("Diesel Exhaust Fluid Valve Circuit Failed Low") on a sibling part: Detroit lists SPN 4354 FMI 4 as "Line Heater #1 Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 4354 FMI 5Line Heater 1 Open Circuit

    Same failure as SPN 3363 FMI 5 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed Open") on a sibling part: Detroit lists SPN 4354 FMI 5 as "Line Heater 1 Open Circuit".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 4355 FMI 3Line Heater #2 Circuit Failed High

    Same failure as SPN 3363 FMI 3 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed High") on a sibling part: Detroit lists SPN 4355 FMI 3 as "Line Heater #2 Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 4355 FMI 4Line Heater #2 Circuit Failed Low

    Same failure as SPN 3363 FMI 4 ("Diesel Exhaust Fluid Valve Circuit Failed Low") on a sibling part: Detroit lists SPN 4355 FMI 4 as "Line Heater #2 Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 4355 FMI 5Line Heater 2 Open Circuit

    Same failure as SPN 3363 FMI 5 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed Open") on a sibling part: Detroit lists SPN 4355 FMI 5 as "Line Heater 2 Open Circuit".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 4356 FMI 3Line Heater #3 Circuit Failed High

    Same failure as SPN 3363 FMI 3 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed High") on a sibling part: Detroit lists SPN 4356 FMI 3 as "Line Heater #3 Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 4356 FMI 4Line Heater #3 Circuit Failed Low

    Same failure as SPN 3363 FMI 4 ("Diesel Exhaust Fluid Valve Circuit Failed Low") on a sibling part: Detroit lists SPN 4356 FMI 4 as "Line Heater #3 Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 4356 FMI 5Line Heater 3 Open Circuit

    Same failure as SPN 3363 FMI 5 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed Open") on a sibling part: Detroit lists SPN 4356 FMI 5 as "Line Heater 3 Open Circuit".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 4357 FMI 3Line Heater #4 Circuit Failed High

    Same failure as SPN 3363 FMI 3 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed High") on a sibling part: Detroit lists SPN 4357 FMI 3 as "Line Heater #4 Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 4357 FMI 4Line Heater #4 Circuit Failed Low

    Same failure as SPN 3363 FMI 4 ("Diesel Exhaust Fluid Valve Circuit Failed Low") on a sibling part: Detroit lists SPN 4357 FMI 4 as "Line Heater #4 Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 4357 FMI 5Line Heater 4 Open Circuit

    Same failure as SPN 3363 FMI 5 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed Open") on a sibling part: Detroit lists SPN 4357 FMI 5 as "Line Heater 4 Open Circuit".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 5488 FMI 3Diesel Exhaust Fluid Line Heater 5 Circuit Failed High

    Same failure as SPN 3363 FMI 3 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed High") on a sibling part: Detroit lists SPN 5488 FMI 3 as "Diesel Exhaust Fluid Line Heater 5 Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 5488 FMI 4Diesel Exhaust Fluid Line Heater 5 Circuit Failed Low

    Same failure as SPN 3363 FMI 4 ("Diesel Exhaust Fluid Valve Circuit Failed Low") on a sibling part: Detroit lists SPN 5488 FMI 4 as "Diesel Exhaust Fluid Line Heater 5 Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 5488 FMI 5Selective Catalyst Reduction Line Heater 5 Circuit Failed Open

    Same failure as SPN 3363 FMI 5 ("Diesel Exhaust Fluid Coolant Valve Circuit Failed Open") on a sibling part: Detroit lists SPN 5488 FMI 5 as "Selective Catalyst Reduction Line Heater 5 Circuit Failed Open".· Open circuit
    Check soon

    Causes

    • The causes listed under SPN 3363 FMI 5, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 3363 FMI 5, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Detroit SPN 520383 FMI 2DEF Tank Temperature - Cool Down

    Detroit lists SPN 520383 FMI 2 as "DEF Tank Temperature - Cool Down".· Erratic or implausible
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the DEF heater
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the DEF heater in the tool and watch the result.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 520383 FMI 10DEF Tank Temperature - Warm Up

    Detroit lists SPN 520383 FMI 10 as "DEF Tank Temperature - Warm Up".· Erratic or implausible
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the DEF heater
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the DEF heater in the tool and watch the result.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

Shared checks

Checks, in order

  1. 1Measure the heater element resistance and compare it with the other line heaters on the same truck.
  2. 2Inspect the heater connectors for corrosion, water and bent pins.
  3. 3Check the heater wiring for chafing and a short to ground or battery.
  4. 4Check the coolant valve that supplies the tank heating for correct operation.

Causes

  • Heater element failure
  • Open or shorted wiring
  • Connector damage
  • Coolant valve problem

Most common here: shorted high (7 of 25)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: DEF system faults in cold weather, a frozen line or doser, and a possible derate if dosing stops.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.