Detroit · Aftertreatment
Detroit DEF dosing pump, pressure and flow fault codes
The DEF dosing unit pumps diesel exhaust fluid to the doser. These codes cover its circuits, pump speed, pressure control, flow and over-pressure faults.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 3361 FMI 1 to SPN 520342 FMI 17 are all about the dEF dosing pump, pressure and flow. The most common failure type is real condition (8 of 24); none needs an immediate stop. Start with this check: check the DEF level and quality before testing any electrical part of the dosing unit.
How urgent are they?
None of the 24 codes here means stop now; all 24 can wait until the shift ends, but find the cause before the next one.
- Check soon24
What should I check first?
Check the DEF level and quality before testing any electrical part of the dosing unit.
Shared checks24 of 24
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 3361 FMI 1Automatic Self-Check of DEF Dosing System Not Done
Detroit lists SPN 3361 FMI 1 as "Automatic Self-Check of DEF Dosing System Not Done". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF dosing unit pumps and meters the fluid; its self-check on the system tests the pump, valve and pressure before dosing.· Real conditionReal conditionCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The automatic self-check of the dosing system was not done; run the dosing system test in the tool.
- 4The self-check runs at key-off; leave the key off long enough for the system to run the check and see if it completes.
- 5The automatic self-check runs after key-off while the unit purges the lines, so cutting battery power during after-run can leave it unfinished.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 3361 FMI 3Diesel Exhaust Fluid System Circuit Failed High
Detroit lists SPN 3361 FMI 3 as "Diesel Exhaust Fluid System Circuit Failed High". The ACM found the DEF pump circuit shorted high or reading above its limit, which usually means a short to battery on the output wire. The DEF dosing unit pumps and meters the fluid; its self-check on the system tests the pump, valve and pressure before dosing.· Shorted highShorted highCheck soonCauses
- Output wire of the DEF pump rubbed through and touching a live wire
- Internal short in the DEF pump
Checks
- 1Unplug the DEF pump and look for voltage on the output wire with the key on.
- 2Measure the DEF pump winding resistance and compare it with a good unit.
- 3The DEF dosing system circuit is shorted high; check the unit connector and wires for a short to supply.
- 4High circuit: look for a short to supply in the dosing unit harness.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3361 FMI 4Diesel Exhaust Fluid System Circuit Failed Low
Detroit lists SPN 3361 FMI 4 as "Diesel Exhaust Fluid System Circuit Failed Low". The ACM found the DEF pump circuit shorted low or reading below its limit, which usually means a short to ground. The DEF dosing unit pumps and meters the fluid; its self-check on the system tests the pump, valve and pressure before dosing.· Shorted lowShorted lowCheck soonCauses
- Output wire of the DEF pump rubbed through against the engine
- Internal short in the DEF pump
Checks
- 1Unplug the DEF pump and check the output wire for continuity to ground.
- 2Measure the DEF pump winding resistance and look for a very low value.
- 3The DEF dosing system circuit is shorted low; check the unit connector and wires for a short to ground.
- 4Low circuit: look for a short to ground in the dosing unit harness.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3361 FMI 5Diesel Exhaust Fluid System Circuit Failed Open
Detroit lists SPN 3361 FMI 5 as "Diesel Exhaust Fluid System Circuit Failed Open". The ACM found the DEF pump circuit open, so no current flows when the output is switched on. The DEF dosing unit pumps and meters the fluid; its self-check on the system tests the pump, valve and pressure before dosing.· Open circuitOpen circuitCheck soonCauses
- Open wire or pushed-out pin at the DEF pump connector
- Burned-out DEF pump coil
Checks
- 1Check continuity from the ACM pin to the DEF pump connector and back.
- 2Measure the DEF pump winding resistance; an open reading means the part has failed.
- 3The DEF dosing system circuit is open; check the unit connector pins and the wires for a break.
- 4Open circuit: look for a broken wire in the dosing unit harness.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 3361 FMI 31Diesel Exhaust Fluid Dosing Unit Error
The ACM reports an error in the DEF dosing unit that it cannot classify further. It is a general fault of the dosing system and often comes with other DEF codes.· Real conditionReal conditionCheck soonCauses
- Dosing unit electrical or mechanical failure
- DEF supply or pressure problem
- Frozen DEF in the unit
Checks
- 1Read all other DEF codes first; they usually point at the real cause of this general dosing fault.
- 2Check the DEF level and the dosing unit connector for damage and corrosion.
- 3Run the dosing test in the tool and compare the pump speed with the pressure.
- 4Inspect the dosing unit for leaks, crystals and frozen fluid.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4331 FMI 15DEF Dosing Quantity Low
Detroit lists SPN 4331 FMI 15 as "DEF Dosing Quantity Low". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF dosing quantity is checked against the quantity the ACM ordered; low delivery points to pump, line or nozzle problems.· Real conditionReal conditionCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF dosing quantity is low; check the nozzle for crystals and the lines for restrictions.
- 4Low dosing quantity: remove the doser and look for crystals in the nozzle.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4334 FMI 3Diesel Exhaust Fluid Pressure Sensor Circuit Failed High
Same failure as SPN 3361 FMI 3 ("Diesel Exhaust Fluid System Circuit Failed High") on a sibling part: Detroit lists SPN 4334 FMI 3 as "Diesel Exhaust Fluid Pressure Sensor Circuit Failed High". The DEF pressure sensor measures the pressure of the fluid delivered by the pump to the doser.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 3361 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3361 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 4334 FMI 4Diesel Exhaust Fluid Pressure Sensor Circuit Failed Low
Same failure as SPN 3361 FMI 4 ("Diesel Exhaust Fluid System Circuit Failed Low") on a sibling part: Detroit lists SPN 4334 FMI 4 as "Diesel Exhaust Fluid Pressure Sensor Circuit Failed Low". The DEF pressure sensor measures the pressure of the fluid delivered by the pump to the doser.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3361 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3361 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 4374 FMI 0Under Pressurized Diesel Exhaust Fluid System
The ACM found the DEF system under-pressurised: the pump cannot reach the pressure the doser needs. Detroit logs this before dosing becomes inaccurate.· Real conditionReal conditionCheck soonCauses
- Low DEF level or frozen fluid
- Plugged DEF filter or crystals in the lines
- Air in the system after a refill
- Pump worn out
Checks
- 1Check the DEF level and make sure the fluid is not frozen in the tank or in the lines.
- 2Inspect the DEF filter and the lines for crystals, kinks and leaks.
- 3Run the dosing test in the tool and watch the pump speed and the pressure.
- 4Check the pump connector and wiring for corrosion and damage.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4374 FMI 1Over Pressurized DEF System
Detroit lists SPN 4374 FMI 1 as "Over Pressurized DEF System". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF pump pressure and speed are controlled by the ACM; faults describe the pump speed, over-pressure and loop control errors.· Real conditionReal conditionCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF system is over-pressurised; check the lines and the doser for blockage or frozen fluid.
- 4Over pressure: look for a blocked doser nozzle or a pinched pressure line.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4374 FMI 3Diesel Exhaust Fluid (DEF) Pump Speed Signal Above Measurement Range
Detroit lists SPN 4374 FMI 3 as "Diesel Exhaust Fluid (DEF) Pump Speed Signal Above Measurement Range". The ACM found the DEF pump circuit shorted high or reading above its limit, which usually means a short to battery on the output wire. The DEF pump pressure and speed are controlled by the ACM; faults describe the pump speed, over-pressure and loop control errors.· Shorted highShorted highCheck soonCauses
- Output wire of the DEF pump rubbed through and touching a live wire
- Internal short in the DEF pump
Checks
- 1Unplug the DEF pump and look for voltage on the output wire with the key on.
- 2Measure the DEF pump winding resistance and compare it with a good unit.
- 3The pump speed signal is above range; check the pump speed sensor wire and the pump.
- 4Pump speed signal above range: check the pump speed wire and the pump for a short.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 4374 FMI 4Aftertreatment Control Module (ACM) Detects that the DEF PumpSpeed Signal is below a Calibrated Range
Detroit lists SPN 4374 FMI 4 as "Aftertreatment Control Module (ACM) Detects that the DEF PumpSpeed Signal is below a Calibrated Range". The ACM found the DEF pump circuit shorted low or reading below its limit, which usually means a short to ground. The DEF pump pressure and speed are controlled by the ACM; faults describe the pump speed, over-pressure and loop control errors.· Shorted lowShorted lowCheck soonCauses
- Output wire of the DEF pump rubbed through against the engine
- Internal short in the DEF pump
Checks
- 1Unplug the DEF pump and check the output wire for continuity to ground.
- 2Measure the DEF pump winding resistance and look for a very low value.
- 3The pump speed signal is below the calibrated limit; check the pump and its speed sensor.
- 4Pump speed signal below range: check the pump motor and its speed wire for an open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 4374 FMI 9DEF PSV Loop Error
Detroit lists SPN 4374 FMI 9 as "DEF PSV Loop Error". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF pump pressure and speed are controlled by the ACM; faults describe the pump speed, over-pressure and loop control errors.· Lost messageLost messageCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF PSV loop has an error; check the pressure sensor and the control valve.
- 4The PSV loop error points to the pressure control valve; check it for sticking.
- 5The PSV is the pressure and shut-off valve of the dosing unit; a loop error means the valve does not hold the pressure the pump builds, so listen for the valve click when the system primes.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 4374 FMI 11DEF PNV SRH Loop Error (Pump Speed Low)
Detroit lists SPN 4374 FMI 11 as "DEF PNV SRH Loop Error (Pump Speed Low)". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF pump pressure and speed are controlled by the ACM; faults describe the pump speed, over-pressure and loop control errors.· OtherOtherCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF pump speed loop error with low speed; check the pump motor for binding.
- 4The pump runs slowly in the control loop; check the pump motor and the supply.
- 5A low pump speed in the control loop with the pressure still not reached suggests a pump that is weak or a suction line that sucks air, so check the line joints.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 4374 FMI 14DEF PNV SRH Loop Error (Pump Speed High)
Detroit lists SPN 4374 FMI 14 as "DEF PNV SRH Loop Error (Pump Speed High)". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF pump pressure and speed are controlled by the ACM; faults describe the pump speed, over-pressure and loop control errors.· OtherOtherCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF pump speed loop error with high speed; check for leaks that let the pump overrun.
- 4The pump runs fast in the control loop; check for a leak that lets pressure escape.
- 5A high pump speed in the control loop means the controller keeps raising the speed to hold pressure, which points at a leaking line or valve downstream of the pump.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 4374 FMI 19Diesel Exhaust Fluid System is Not Being Controlled as Expected
Detroit lists SPN 4374 FMI 19 as "Diesel Exhaust Fluid System is Not Being Controlled as Expected". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF pump pressure and speed are controlled by the ACM; faults describe the pump speed, over-pressure and loop control errors.· Lost messageLost messageCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF system is not controlled as expected; check the level, the filter and the pump.
- 4The system is not controlled as expected; check the pressure sensor and the pump together.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 4375 FMI 3Diesel Exhaust Fluid Pump Circuit Failed High
Same failure as SPN 3361 FMI 3 ("Diesel Exhaust Fluid System Circuit Failed High") on a sibling part: Detroit lists SPN 4375 FMI 3 as "Diesel Exhaust Fluid Pump Circuit Failed High". The DEF pump motor circuit is driven by the ACM; a high, low or open entry names the type of electrical fault.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 3361 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3361 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 4375 FMI 4Diesel Exhaust Fluid Pump Circuit Failed Low
Same failure as SPN 3361 FMI 4 ("Diesel Exhaust Fluid System Circuit Failed Low") on a sibling part: Detroit lists SPN 4375 FMI 4 as "Diesel Exhaust Fluid Pump Circuit Failed Low". The DEF pump motor circuit is driven by the ACM; a high, low or open entry names the type of electrical fault.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3361 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3361 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 4375 FMI 5Diesel Exhaust Fluid Pump Circuit Failed Open
Same failure as SPN 3361 FMI 5 ("Diesel Exhaust Fluid System Circuit Failed Open") on a sibling part: Detroit lists SPN 4375 FMI 5 as "Diesel Exhaust Fluid Pump Circuit Failed Open". The DEF pump motor circuit is driven by the ACM; a high, low or open entry names the type of electrical fault.· Open circuitOpen circuitCheck soonCauses
- The causes listed under SPN 3361 FMI 5, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3361 FMI 5, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 5435 FMI 7Non Diesel Exhaust Fluid Flow Situation
Detroit lists SPN 5435 FMI 7 as "Non Diesel Exhaust Fluid Flow Situation". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF flow situation is checked while the pump runs; blocked loop errors point to blocked lines or a stuck pump.· Part or controllerPart or controllerCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3A non-DEF flow situation means fluid other than DEF is passing; check the fluid and the lines.
- 4Non-DEF flow: check that the fluid in the tank is DEF and the lines are not cross-connected.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 5435 FMI 11DEF Pump Blocked Loop Error
Detroit lists SPN 5435 FMI 11 as "DEF Pump Blocked Loop Error". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF flow situation is checked while the pump runs; blocked loop errors point to blocked lines or a stuck pump.· Real conditionReal conditionCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF pump blocked-loop error means the pump is blocked; check for frozen fluid and crystals.
- 4Blocked loop: check for frozen DEF or crystals blocking the pump.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520328 FMI 7Diesel Exhaust Fluid System Has Been Over-pressurized
Detroit lists SPN 520328 FMI 7 as "Diesel Exhaust Fluid System Has Been Over-pressurized". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF system was over-pressurised, which can crack lines or the pump.· Part or controllerPart or controllerCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF system was over-pressurised; inspect the lines and the pump for damage.
- 4Over-pressurised: inspect the lines and pump for cracks from the pressure.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 520329 FMI 31DEF Flow Quantity Below Normal
Detroit lists SPN 520329 FMI 31 as "DEF Flow Quantity Below Normal". The ACM reports a condition on the DEF pump that it could not clear on its own. DEF flow below normal means the pump delivers less than ordered.· Real conditionReal conditionCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF flow is below normal; check the filter, the lines and the nozzle.
- 4Flow below normal: check the filter, the lines and the nozzle.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520342 FMI 17DEF System Rationality DEF Pump Speed High
Detroit lists SPN 520342 FMI 17 as "DEF System Rationality DEF Pump Speed High". The ACM reports a condition on the DEF pump that it could not clear on its own. The DEF pump speed was high compared with the pressure it delivers, which suggests a leak or blocked line.· Real conditionReal conditionCheck soonCauses
- Wiring, supply or mechanical problem on the DEF pump
- Controller output fault
Checks
- 1Read the freeze-frame data for this code and note the engine state.
- 2Command the DEF pump in the tool and watch the result.
- 3The DEF pump speed is high for the delivered pressure; check for a leak.
- 4Pump speed high for the pressure: look for a leak in the line or the pump.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Check the DEF level and quality before testing any electrical part of the dosing unit.
- 2Inspect the DEF lines and the doser for crystals, kinks and leaks.
- 3Check the pump connector and the pump wiring for corrosion and damage.
- 4Run the dosing or pressure test in the diagnostic tool and watch the pump speed.
Causes
- Frozen or crystallised DEF in the pump or lines
- Plugged filter or doser
- Pump failure
- Wiring fault
Most common here: real condition (8 of 24)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: DEF warning lamps, a loss of power and a derate if not corrected.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
