Detroit · Air system
Detroit Charge air, intake manifold and ambient temperature fault codes
These sensors watch the compressor inlet, the charge air cooler outlet, the intake manifold and the ambient air. The MCM uses them to protect the engine and to judge the cooler efficiency.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 171 FMI 2 to SPN 5125 FMI 14 are all about the charge air, intake manifold and ambient temperature. The most common failure type is erratic or implausible (9 of 24); none needs an immediate stop. Start with this check: compare the tool reading of each temperature with a surface thermometer on a cold engine.
How urgent are they?
None of the 24 codes here means stop now; all 24 can wait until the shift ends, but find the cause before the next one.
- Check soon24
What should I check first?
Compare the tool reading of each temperature with a surface thermometer on a cold engine.
Shared checks24 of 24
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 171 FMI 2Ambient Air Temperature Sensor, General Temperature Plausibility Error
Detroit lists SPN 171 FMI 2 as "Ambient Air Temperature Sensor, General Temperature Plausibility Error". The MCM judged the intake temperature sensor reading erratic or not plausible compared with other sensors or its own history. The ambient air temperature sensor sits outside the engine bay on the vehicle; its value corrects cold start and fan behaviour.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting intake temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the intake temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 171 FMI 3Ambient Temperature Sensor Failed High or Open
Detroit lists SPN 171 FMI 3 as "Ambient Temperature Sensor Failed High or Open". The MCM saw the intake temperature sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The ambient air temperature sensor sits outside the engine bay on the vehicle; its value corrects cold start and fan behaviour.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the intake temperature sensor and the MCM
- The intake temperature sensor has failed inside
Checks
- 1Unplug the intake temperature sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 171 FMI 4Ambient Temperature Sensor Failed Low
Detroit lists SPN 171 FMI 4 as "Ambient Temperature Sensor Failed Low". The MCM saw the intake temperature sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The ambient air temperature sensor sits outside the engine bay on the vehicle; its value corrects cold start and fan behaviour.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The intake temperature sensor has failed inside or its supply wire is open
Checks
- 1Unplug the intake temperature sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 171 FMI 13Ambient Air Temperature Signal Not Available via the Controller Area Network
Detroit lists SPN 171 FMI 13 as "Ambient Air Temperature Signal Not Available via the Controller Area Network". The MCM found the intake temperature sensor value drifted away from what the engine state says it should be. The ambient air temperature sensor sits outside the engine bay on the vehicle; its value corrects cold start and fan behaviour.· Part or controllerPart or controllerCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the intake temperature sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the intake temperature sensor for leaks, restrictions or contamination.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 171 FMI 19Ambient Air Temperature Signal Error
Detroit lists SPN 171 FMI 19 as "Ambient Air Temperature Signal Error". The MCM lost the intake temperature sensor signal completely. The ambient air temperature sensor sits outside the engine bay on the vehicle; its value corrects cold start and fan behaviour.· Lost messageLost messageCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the intake temperature sensor.
- 2Check the signal wire to the MCM for an open.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 171 FMI 20Ambient Temperature Sensor Signal Not Plausible
Same failure as SPN 171 FMI 2 ("Ambient Air Temperature Sensor, General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 171 FMI 20 as "Ambient Temperature Sensor Signal Not Plausible". The ambient air temperature sensor sits outside the engine bay on the vehicle; its value corrects cold start and fan behaviour.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 171 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1172 FMI 3Turbocharger Compressor Inlet Temperature Sensor or Circuit Failed High
Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 1172 FMI 3 as "Turbocharger Compressor Inlet Temperature Sensor or Circuit Failed High". The compressor inlet temperature sensor sits before the turbo compressor and gives the controller the air temperature the turbo is breathing.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 1172 FMI 4Turbocharger Compressor Inlet Temperature Circuit Failed Low
Same failure as SPN 171 FMI 4 ("Ambient Temperature Sensor Failed Low") on a sibling part: Detroit lists SPN 1172 FMI 4 as "Turbocharger Compressor Inlet Temperature Circuit Failed Low". The compressor inlet temperature sensor sits before the turbo compressor and gives the controller the air temperature the turbo is breathing.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 171 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 1172 FMI 14Turbocharger Compressor Inlet Temperature Sensor Drift in Range
Detroit lists SPN 1172 FMI 14 as "Turbocharger Compressor Inlet Temperature Sensor Drift in Range". The MCM judged the intake temperature sensor reading erratic or not plausible compared with other sensors or its own history. The compressor inlet temperature sensor sits before the turbo compressor and gives the controller the air temperature the turbo is breathing.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting intake temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the intake temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1172 FMI 21Compressor Inlet Temperature Sensor Signal Not Plausible
Same failure as SPN 171 FMI 2 ("Ambient Air Temperature Sensor, General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 1172 FMI 21 as "Compressor Inlet Temperature Sensor Signal Not Plausible". The compressor inlet temperature sensor sits before the turbo compressor and gives the controller the air temperature the turbo is breathing.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 171 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1636 FMI 0Charge Air Cooler Low Efficiency
Detroit lists SPN 1636 FMI 0 as "Charge Air Cooler Low Efficiency". The MCM reports that the measured value itself is out of its normal range; the intake temperature sensor may be correct and a real condition may exist. The intake manifold temperature sensor reads the charge air after the cooler and is used to judge the charge air cooler efficiency.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the intake temperature sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the intake temperature sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 1636 FMI 3Intake Manifold Temperature Circuit Failed High
Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 1636 FMI 3 as "Intake Manifold Temperature Circuit Failed High". The intake manifold temperature sensor reads the charge air after the cooler and is used to judge the charge air cooler efficiency.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 1636 FMI 4Intake Manifold Temperature Circuit Failed Low
Same failure as SPN 171 FMI 4 ("Ambient Temperature Sensor Failed Low") on a sibling part: Detroit lists SPN 1636 FMI 4 as "Intake Manifold Temperature Circuit Failed Low". The intake manifold temperature sensor reads the charge air after the cooler and is used to judge the charge air cooler efficiency.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 171 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 1636 FMI 10Intake Manifold Temperature - Signal Spike
Detroit lists SPN 1636 FMI 10 as "Intake Manifold Temperature - Signal Spike". The MCM judged the intake temperature sensor reading erratic or not plausible compared with other sensors or its own history. The intake manifold temperature sensor reads the charge air after the cooler and is used to judge the charge air cooler efficiency.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting intake temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the intake temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1636 FMI 14Intake Manifold Temperature Sensor Signal Not Plausible
Same failure as SPN 171 FMI 2 ("Ambient Air Temperature Sensor, General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 1636 FMI 14 as "Intake Manifold Temperature Sensor Signal Not Plausible". The intake manifold temperature sensor reads the charge air after the cooler and is used to judge the charge air cooler efficiency.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 171 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1636 FMI 16Charge Air Cooler Efficiency Low
Detroit lists SPN 1636 FMI 16 as "Charge Air Cooler Efficiency Low". The MCM reports that the measured value itself is out of its normal range; the intake temperature sensor may be correct and a real condition may exist. The intake manifold temperature sensor reads the charge air after the cooler and is used to judge the charge air cooler efficiency.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the intake temperature sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the intake temperature sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 1636 FMI 21Intake Manifold Temperature Drift-High Box
Detroit lists SPN 1636 FMI 21 as "Intake Manifold Temperature Drift-High Box". The MCM found the intake temperature sensor value drifted away from what the engine state says it should be. The intake manifold temperature sensor reads the charge air after the cooler and is used to judge the charge air cooler efficiency.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the intake temperature sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the intake temperature sensor for leaks, restrictions or contamination.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1636 FMI 31Intake Manifold Temperature Sensor Drift in Range
Same failure as SPN 1172 FMI 14 ("Turbocharger Compressor Inlet Temperature Sensor Drift in Range") on a sibling part: Detroit lists SPN 1636 FMI 31 as "Intake Manifold Temperature Sensor Drift in Range". The intake manifold temperature sensor reads the charge air after the cooler and is used to judge the charge air cooler efficiency.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 1172 FMI 14, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1172 FMI 14, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 2630 FMI 3Charge Air Cooler Outlet Temperature Circuit Failed High
Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 2630 FMI 3 as "Charge Air Cooler Outlet Temperature Circuit Failed High". The charge air cooler outlet temperature sensor sits in the pipe after the cooler and shows how well the cooler removes heat.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 2630 FMI 4Intake Air Temperature Circuit Failed Low
Same failure as SPN 171 FMI 4 ("Ambient Temperature Sensor Failed Low") on a sibling part: Detroit lists SPN 2630 FMI 4 as "Intake Air Temperature Circuit Failed Low". The charge air cooler outlet temperature sensor sits in the pipe after the cooler and shows how well the cooler removes heat.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 171 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 2630 FMI 14Charge Air Cooler Outlet Sensor Signal Not Plausible
Same failure as SPN 171 FMI 2 ("Ambient Air Temperature Sensor, General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 2630 FMI 14 as "Charge Air Cooler Outlet Sensor Signal Not Plausible". The charge air cooler outlet temperature sensor sits in the pipe after the cooler and shows how well the cooler removes heat.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 171 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 5125 FMI 3Ambient Temperature Sensor Failed High or Open
Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 5125 FMI 3 as "Ambient Temperature Sensor Failed High or Open". The ambient temperature signal on a CPC5 pin is monitored for overtemperature and for a short or open on the sensor line.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 5125 FMI 4Ambient Temperature Sensor Failed High or Open
Same failure as SPN 171 FMI 3 ("Ambient Temperature Sensor Failed High or Open") on a sibling part: Detroit lists SPN 5125 FMI 4 as "Ambient Temperature Sensor Failed High or Open". The ambient temperature signal on a CPC5 pin is monitored for overtemperature and for a short or open on the sensor line.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 171 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 171 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 5125 FMI 14CPC5 Overtemp - Pin X3_35
Detroit lists SPN 5125 FMI 14 as "CPC5 Overtemp - Pin X3_35". The MCM judged the intake temperature sensor reading erratic or not plausible compared with other sensors or its own history. The ambient temperature signal on a CPC5 pin is monitored for overtemperature and for a short or open on the sensor line.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting intake temperature sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the intake temperature sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Compare the tool reading of each temperature with a surface thermometer on a cold engine.
- 2Inspect the sensor connectors for oil and corrosion and check the harness for chafing.
- 3Pressure-test the charge air system and the cooler for leaks.
- 4Check the radiator and cooler fins for debris and blocked airflow.
- 5Replace the sensor only when the wiring and cooler tests are good.
Causes
- Charge air cooler leak, plugged fins or restricted airflow
- Sensor connector damage or wiring short
- Contaminated or drifted sensor
- Cooling air blocked or an ambient sensor mounted in a hot spot
Most common here: erratic or implausible (9 of 24)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: A loss of power, black smoke or poor cold-start behaviour, and the check-engine lamp.
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
