Cummins · Data link
Cummins Connectivity radios, antennas and motion sensors fault codes
The connectivity module has cellular, GPS, Wi-Fi and Bluetooth radios, a SIM and external antennas. The connectivity module has an accelerometer and gyro for event detection and an internal link between its processors.
Where to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
What do these codes mean?
Cummins codes 8194 to 8229 are all about the connectivity radios, antennas and motion sensors. The most common failure type is part or controller (6 of 13); none needs an immediate stop. Start with this check: inspect the antenna cables and connectors for damage and water.
How urgent are they?
None of the 13 codes here means stop now; all 13 can wait until the shift ends, but find the cause before the next one.
- Check soon13
What should I check first?
Inspect the antenna cables and connectors for damage and water
Shared checks13 of 13
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Communications service subscriber identification module1 code
Cummins 8194Communications service subscriber identification module: Bad device or component
The ECM flags the communications service subscriber identification module as a bad device or component after a self-test or a response check failed. The part itself is the most likely cause.· Part or controllerPart or controllerCheck soonCauses
- Failed communications service subscriber identification module or its internal electronics
- Supply or ground fault that made the self-test fail
- Connector or harness damage that stops the part from communicating
Checks
- 1Check supply voltage and ground at the communications service subscriber identification module before replacing it
- 2Inspect the communications service subscriber identification module connector and wiring for water, corrosion and damage
- 3Read the communications service subscriber identification module for any stored status or self-test result with the service tool
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Connectivity module cellular1 code
Cummins 8198Connectivity module cellular: Bad device or component
Same failure as 8194 on the connectivity module cellular: the same fault condition as 8194, reported for this part. The cellular modem is the part that talks to the mobile network, so a fault stops remote data and updates.· Lost messageLost messageCheck soonCauses
- Same causes as 8194, applied to the connectivity module cellular
- Wiring or connector problem local to the connectivity module cellular
Checks
- 1Check the modem supply and signal strength in a location with good coverage.
- 2Work through the checks listed for 8194, starting at the connectivity module cellular and its connector
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Connectivity module USB1 code
Cummins 8199Connectivity module USB: Bad device or component
Same failure as 8194 on the connectivity module USB: the same fault condition as 8194, reported for this part. The connectivity module USB port is used for local data and update transfer.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 8194, applied to the connectivity module USB
- Wiring or connector problem local to the connectivity module USB
Checks
- 1Inspect the USB connector and cable for damage and try a different device.
- 2Work through the checks listed for 8194, starting at the connectivity module USB and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Connectivity module cellular external antenna2 codes
Cummins 8211Connectivity module cellular external antenna: Current low / open circuit
The ECM sees too little current, or no current, in the connectivity module cellular external antenna. The circuit is open, or the driver is not connected to its load, so the part is not doing its job.· Open circuitOpen circuitCheck soonCauses
- Broken or pulled-out wire in the harness to the connectivity module cellular external antenna
- Connector at the connectivity module cellular external antenna unplugged, loose or with a pin pushed back
- Burnt-out coil or element in the part itself
Checks
- 1Unplug the connectivity module cellular external antenna and measure the resistance of the part itself against the service manual value, since an infinite reading means the part is open
- 2Check continuity of both wires between the connectivity module cellular external antenna connector and the ECM connector
- 3Wiggle the harness and connector at the connectivity module cellular external antenna while watching the live status to catch an intermittent open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Source wording:Connectivity module cellular external antenna - current low or open circuit
Cummins 8212Connectivity module cellular external antenna: Voltage high / shorted high
The ECM reads the connectivity module cellular external antenna above its allowed voltage band. That points to a short to a 5 V or battery wire, a lost return, or a failed part, rather than a real change in what it measures.· Shorted highShorted highCheck soonCauses
- Short to a 5 V reference or a battery wire in the harness to the connectivity module cellular external antenna
- Open or high-resistance return wire that lets the signal float high
- Water or corrosion in the connector bridging two pins together
Checks
- 1Key on, unplug the connectivity module cellular external antenna and read its circuit at the harness: a high reading with the part removed means the wiring is shorted high or the return is lost
- 2Jumper the signal wire of the connectivity module cellular external antenna to ground at the harness and see whether the code changes to a low-voltage code, which proves the wiring and the ECM input
- 3Check continuity and resistance of the return wire from the connectivity module cellular external antenna back to the ECM
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Connectivity module cellular external antenna - voltage high (shorted to a high source)
Connectivity module GPS external antenna2 codes
Cummins 8213Connectivity module GPS external antenna: Current low / open circuit
Same failure as 8211 on the connectivity module GPS external antenna: the same fault condition as 8211, reported for this part. The GPS external antenna gives the module its position, and a fault here means no location data.· Open circuitOpen circuitCheck soonCauses
- Same causes as 8211, applied to the connectivity module GPS external antenna
- Wiring or connector problem local to the connectivity module GPS external antenna
Checks
- 1Check the GPS antenna cable and connector and that the antenna has a clear view of the sky.
- 2Work through the checks listed for 8211, starting at the connectivity module GPS external antenna and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Source wording:Connectivity module GPS external antenna - current low or open circuit
Cummins 8214Connectivity module GPS external antenna: Voltage high / shorted high
Same failure as 8212 on the connectivity module GPS external antenna: the same fault condition as 8212, reported for this part. The GPS external antenna gives the module its position, and a fault here means no location data.· Shorted highShorted highCheck soonCauses
- Same causes as 8212, applied to the connectivity module GPS external antenna
- Wiring or connector problem local to the connectivity module GPS external antenna
Checks
- 1Check the GPS antenna cable and connector and that the antenna has a clear view of the sky.
- 2Work through the checks listed for 8212, starting at the connectivity module GPS external antenna and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Connectivity module GPS external antenna - voltage high (shorted to a high source)
Connectivity module Wi-Fi1 code
Cummins 8215Connectivity module Wi-Fi: Bad device or component
Same failure as 8194 on the connectivity module Wi-Fi: the same fault condition as 8194, reported for this part. The Wi-Fi radio is used for local network and update connections.· Lost messageLost messageCheck soonCauses
- Same causes as 8194, applied to the connectivity module Wi-Fi
- Wiring or connector problem local to the connectivity module Wi-Fi
Checks
- 1Check the Wi-Fi settings and the module supply, and reset the module.
- 2Work through the checks listed for 8194, starting at the connectivity module Wi-Fi and its connector
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Connectivity module Bluetooth1 code
Cummins 8216Connectivity module Bluetooth: Bad device or component
Same failure as 8194 on the connectivity module Bluetooth: the same fault condition as 8194, reported for this part. The Bluetooth radio pairs the module with local devices such as a phone or a service tool.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 8194, applied to the connectivity module Bluetooth
- Wiring or connector problem local to the connectivity module Bluetooth
Checks
- 1Check pairing and the module supply, and reset the module.
- 2Work through the checks listed for 8194, starting at the connectivity module Bluetooth and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Connectivity module accelerometer1 code
Cummins 8217Connectivity module accelerometer: Bad device or component
Same failure as 8194 on the connectivity module accelerometer: the same fault condition as 8194, reported for this part. The accelerometer measures the vehicle motion and impacts that the connectivity module reports.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 8194, applied to the connectivity module accelerometer
- Wiring or connector problem local to the connectivity module accelerometer
Checks
- 1Check the module mounting is firm and level.
- 2Work through the checks listed for 8194, starting at the connectivity module accelerometer and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Connectivity module gyro1 code
Cummins 8218Connectivity module gyro: Bad device or component
Same failure as 8194 on the connectivity module gyro: the same fault condition as 8194, reported for this part. The gyro measures rotation of the vehicle for the connectivity module position and motion data.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 8194, applied to the connectivity module gyro
- Wiring or connector problem local to the connectivity module gyro
Checks
- 1Check the module mounting is firm and level and let the module calibrate with the engine off.
- 2Work through the checks listed for 8194, starting at the connectivity module gyro and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Connectivity module interprocess communication2 codes
Cummins 8228Connectivity module interprocess communication: Network data in error
The ECM received data for the connectivity module interprocess communication over the network, but the message was flagged as in error. The data is not used and a default is applied.· Lost messageLost messageCheck soonCauses
- Sending module flagging the data as not available or in error
- Data link noise, a wiring fault or a bad terminator
- Mismatched configuration between the ECM and the sending module
Checks
- 1Read the sending module for its own codes and the source sensor for faults
- 2Check the data link wiring and terminators for faults near the connectivity module interprocess communication source
- 3Check the ECM and sending module configuration for the connectivity module interprocess communication
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Source wording:Connectivity module interprocess communication - network data received in error
Cummins 8229Connectivity module interprocess communication: Bad device or component
Same failure as 8194 on the connectivity module interprocess communication: the same fault condition as 8194, reported for this part. Interprocess communication is the internal link between the processors in the connectivity module.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 8194, applied to the connectivity module interprocess communication
- Wiring or connector problem local to the connectivity module interprocess communication
Checks
- 1Cycle the key and, if the fault stays, reflash or replace the module.
- 2Work through the checks listed for 8194, starting at the connectivity module interprocess communication and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Shared checks
Checks, in order
- 1Inspect the antenna cables and connectors for damage and water
- 2Check the module power, ground and connector for corrosion
- 3Verify the SIM is seated and active with the carrier
- 4Reload or update the module software with the service tool
- 5Check which radio reports the fault and test it with the service tool
- 6Replace the antenna before the module if the cable test fails
- 7Replace the module if the fault stays after a software update
Causes
- External antenna cable open or shorted
- Sensor or processor failure inside the module
- Antenna connector corroded or loose
- Software fault
Most common here: part or controller (6 of 13)
Check power and ground at the module connector with the key on, then its fuses.
When to stop
You'll notice: Remote data and location services may stop.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
