Cummins · Operator controls - SPN 91 FMI 4
Cummins Fault Code 132
Accelerator pedal position sensor signal voltage low
What does Cummins code 132 mean?
The ECM sees the accelerator pedal position sensor signal below its normal voltage band. Urgency: check soon - the machine may derate or limit a function. Check first: with the key on press the pedal slowly and watch the percent; a reading stuck at zero points to a low signal fault.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
With the key on press the pedal slowly and watch the percent; a reading stuck at zero points to a low signal fault
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Pedal signal wire chafed to ground where it enters the cab floor
- 5 V reference open at the pedal connector, so the sensor has no supply
- Pedal track failed low after internal damage
- Pedal connector pushed on crooked
How it failed
You'll notice: The pedal may do nothing, the engine may sit at a limited idle, or power is cut.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Accelerator pedal and remote throttle
3 other codes on this part are also shorted low (134, 1241, 1361). When they show together, start at the wiring and connector they share.
- 131Accelerator pedal position sensor signal voltage highShorted highCheck soon
- 132Accelerator pedal position sensor signal voltage lowShorted lowCheck soon
- 133Remote accelerator pedal or lever position sensor 1 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 134Remote accelerator pedal or lever position sensor 1 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 288SAE J1939 multiplexing remote accelerator pedal or lever position sensor system - network data received in errorLost messageCheck soon
- 1239Accelerator pedal or lever position sensor 2 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 1241Accelerator pedal or lever position sensor 2 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 1242Accelerator pedal sensors 1 and 2 disagreeLost messageCheck soon
- 1361Remote accelerator pedal or lever position sensor 1 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
Show the other 16 codesHide the other codes
- 1515Multiplexed accelerator pedal signal - network data errorLost messageCheck soon
- 1595Remote accelerator pedal or lever position sensor 1 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 3326SAE J1939 multiplexed accelerator pedal or lever sensor system - abnormal update rateErratic or implausibleCheck soon
- 3527Accelerator pedal or lever idle validation switch - network data received in errorLost messageCheck soon
- 3528Accelerator pedal or lever idle validation switch - abnormal update rateLost messageCheck soon
- 4149Accelerator pedal or lever position sensor 2 circuit frequency - abnormal frequency or pulse widthErratic or implausibleCheck soon
- 4289Accelerator pedal or lever position sensor 1 circuit frequency - abnormal frequency or pulse widthErratic or implausibleCheck soon
- 6417SAE J1939 multiplexing remote accelerator pedal or lever position sensor system - network data received in errorLost messageCheck soon
- 6919Accelerator pedal position 1 - out of calibrationPart or controllerCheck soon
- 14331Accelerator interlock switch - out of calibrationPart or controllerCheck soon
- 14332Accelerator interlock switch - abnormal update rateLost messageCheck soon
- 14372Remote accelerator pedal position - out of calibrationPart or controllerCheck soon
- 14373Remote accelerator enable switch - out of calibrationPart or controllerCheck soon
- 14374Remote accelerator enable switch - abnormal update rateLost messageCheck soon
- 14375Remote accelerator pedal position - abnormal update rateErratic or implausibleCheck soon
- 15691Remote accelerator pedal position - network data received in errorLost messageCheck soon
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 132 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 91, FMI 4); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
