Cummins · Electrical - SPN 3597 FMI 2
Cummins Fault Code 1117
Power supply lost with ignition on
What does Cummins code 1117 mean?
The ECM loses its battery power for a moment while the ignition is on. Urgency: check soon - the machine may derate or limit a function. Check first: check battery terminals and the main ground strap at the block and chassis for tightness and corrosion.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check battery terminals and the main ground strap at the block and chassis for tightness and corrosion
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Loose or corroded battery terminal or ground strap
- ECM power fuse or relay with poor contact
- ECM power connector pin loose, corroded or backed out
- Weak battery or a loose alternator that drops system voltage
How it failed
You'll notice: The engine may stall or stumble, the dash may reboot and lamps may flash.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Battery, charging and ECM power supply
- 478Battery 2 voltage - above normal - moderately severeReal conditionCheck soon
- 596Electrical charging system voltage - above normal - moderately severeReal conditionCheck soon
- 597Charging system voltage low - moderately severeShorted lowCheck soon
- 598Charging system voltage very low - most severeOtherCheck soon
- 1117Power supply lost with ignition onOtherCheck soon
- 1777Power relay driver circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 1938ECU power output supply voltage 1 - below normal - moderately severeReal conditionCheck soon
- 1941ECU power output supply voltage 1 - voltage low (shorted to a low source)Shorted lowCheck soon
- 3724Battery 1 voltage - below normal - least severeReal conditionInformation
Show the other 9 codesHide the other codes
- 441Battery voltage low - moderately severeShorted lowCheck soon
- 442Battery voltage high - moderately severeShorted highCheck soon
- 477Battery 2 voltage - below normal - moderately severeReal conditionCheck soon
- 4951Maintain ECU power lamp - voltage high (shorted to a high source)Shorted highCheck soon
- 4952Maintain ECU power lamp - voltage low (shorted to a low source)Shorted lowCheck soon
- 6256Battery 1 voltage - above normal - least severeReal conditionInformation
- 6257Battery 1 voltage - below normal - least severeReal conditionInformation
- 8343SLI battery pack state of charge - abnormal update rateLost messageCheck soon
- 8346SLI battery pack state of charge - out of calibrationPart or controllerCheck soon
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 1117 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 3597, FMI 2); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
