Cat · Power supply
Cat System voltage, key switch and starting fault codes
This page groups the 24 V charging and supply codes with the starting circuit: the key switch input (CID 1834), the start relay (CID 444) and the cold start aid. The machine runs on a 24 V system fed by two batteries and an alternator.
More about these partsLess
Cold starting on the C6.6 uses a glow plug relay and an ether solenoid, both switched by the engine ECM.
Where this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
What do these codes mean?
Cat codes CID 168 FMI 00 to CID 2417 FMI 05 are all about the system voltage, key switch and starting. The most common failure type is erratic or implausible (4 of 10); 1 needs an immediate stop. Start with this check: measure battery voltage at rest and with the engine at idle and high idle to see the real system voltage.
How urgent are they?
1 of 10 codes here means stop now; the other 9 can wait until the shift ends, but find the cause before the next one.
- Stop now1
- Check soon9
What should I check first?
Measure battery voltage at rest and with the engine at idle and high idle to see the real system voltage.
Shared checks10 of 10
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Cat CID 168 FMI 00Electrical system voltage high
The engine ECM measured battery voltage above 32 V on the 24 V system. On the 924H the manual points straight at the charging system, because a runaway alternator raises the whole system voltage.· Real conditionReal conditionStop nowCauses
- Alternator regulator running away and overcharging
- Alternator output cable or plug fault
- Engine ECM misreading the supply (rare)
Checks
- 1Connect Cat ET, start the engine and confirm 168-0 is active, not just logged.
- 2With a multimeter on the battery posts read system voltage at idle and at high idle and see whether it climbs toward 32 V.
- 3Run the charging system test and look for the alternator voltage too high result.
- 4Inspect the alternator plug and B+ cable ends for heat damage or a loose lug.
- 5Replace the alternator if it overcharges, then rerun and confirm the code goes inactive.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Cat CID 168 FMI 01Electrical system voltage low
The engine ECM saw system voltage fall below the normal 24 V range. The 924H manual walks through harness resistance, ground terminals and the main fuse connection, so the fault is normally in the supply path rather than the batteries.· Real conditionReal conditionCheck soonCauses
- High resistance in the engine or lower cab wiring harness
- Dirty, corroded or loose ground terminals
- Poor connection at the main fuse
- Weak batteries or poor alternator output
Checks
- 1Confirm 168-1 is active on Cat ET with the engine running and note the battery voltage shown.
- 2Measure the main fuse terminal to ground; the manual expects 18 to 26 V, so lower means the loss is upstream.
- 3Measure harness resistance through the lower cab harness; the manual treats 5 ohms or less as acceptable.
- 4Clean and tighten ground terminals 1 and 2 and the battery lugs, then retest.
- 5Replace the engine or lower cab harness only after the voltage drop test points at it.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Cat CID 168 FMI 02Electrical system voltage erratic
System voltage is jumping or reading incorrectly. The manual blames dirty or loose connections, the engine wiring harness or the fuse module 2 cable, so treat it as an intermittent supply problem.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Dirty or corroded connections in the supply path
- Faulty engine wiring harness
- Fuse module 2 cable with a loose terminal
Checks
- 1Wiggle-test the battery cables and ground straps while watching battery voltage on Cat ET.
- 2Measure main fuse terminal 3 to ground; 18 to 26 V is good, below that clean the connection and recheck.
- 3Measure fuse module 2 terminal 4 to ground against the same 18 to 26 V range.
- 4If the connection is fine, replace the fuse module 2 cable, then the engine harness if it is still low.
- 5Clear logged codes, work the machine under load and confirm 168-2 does not return.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cat CID 168 FMI 04Powertrain power supply voltage low
On the 924H the transmission ECM logs this when it reads battery voltage below 18 V. It covers batteries, the charging system, harness resistance, the fuse panel and the ground connection, so it is a supply fault, not a transmission fault.· Shorted lowShorted lowCheck soonCauses
- Weak or failed batteries
- Charging system not keeping up
- High resistance or open in the engine or lower cab harness
- Fuse panel or ground connection fault
Checks
- 1Load-test both batteries; replace any that fail before going further.
- 2Check alternator output with the engine running at the battery posts.
- 3Measure voltage drop from the battery to the transmission ECM supply pin through the fuse panel.
- 4Clean and tighten the ground connection, then clear the code and retest.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Cat CID 444 FMI 03Start relay voltage high
The transmission ECM sees starter relay voltage above normal. The manual lists the lower cab or engine harness shorted to another power source, or the ECM.· Shorted highShorted highCheck soonCauses
- Lower cab wiring harness shorted to a power source
- Engine wiring harness shorted to a power source
- Transmission ECM
Checks
- 1Put the ignition in start for at least 10 seconds with Cat ET connected to the transmission ECM.
- 2Turn off, remove the left engine access panel and unplug connector EN-C4 from the starter relay.
- 3Check the engine harness at the relay for a short to a power feed.
- 4Inspect the lower cab harness at the key switch.
- 5Repair the shorted section of harness first and replace the transmission ECM only if it stays active.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat E875Low system voltage
The ECM detected battery voltage below 18 V. The manual says engine rpm may change and the engine may shut down intermittently or fully.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Weak batteries
- Charging system fault
- Poor ground or supply connections
Checks
- 1Connect Cat ET and check for 168-1 and 168-2 in the active list.
- 2If 168-1 is active, diagnose it with the system voltage procedure.
- 3If 168-2 is active, follow the same procedure for the erratic fault.
- 4Load-test the batteries and replace any that fail.
- 5Check alternator output and the ground connections.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cat E876High system voltage
The ECM detected battery voltage above 32 V. The manual says engine rpm may change and the engine may shut down intermittently or fully.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Overcharging alternator
- Regulator fault
- Loose battery or alternator connection
Checks
- 1Measure charging voltage at the battery with the engine running.
- 2Run the charging system test and read the alternator result.
- 3Replace the alternator if it overcharges, then confirm voltage at the batteries is normal.
- 4Clear the event, then run the engine at high idle and confirm it does not return.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cat CID 1834 FMI 02Ignition key switch circuit erratic
The ECM saw an erratic ignition signal: the switch was cycled at least three times within one second. The manual also lists the harness, the main relay switch, the prime pump and the ECM.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Rapid cycling of the ignition switch
- High resistance or open in the engine or lower cab harness
- Main relay magnetic switch
- Fuel prime pump
- Engine ECM
Checks
- 1Rule out repeated key cycling by the operator before troubleshooting further.
- 2Connect Cat ET and check whether 1834-2 is active.
- 3Inspect and secure ignition circuit connectors.
- 4Test the ignition feed for opens or high resistance at each harness connection.
- 5Check the main relay and prime pump, then the ECM.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cat CID 2246 FMI 05Glow plug start aid relay current low
The ECM found low current, an open circuit, after trying to switch on the glow plug start aid. The manual lists the engine and lower cab harness, the relay coil and the kickout fuse.· Open circuitOpen circuitCheck soonCauses
- High resistance or open in the engine harness
- High resistance or open in the lower cab harness
- Glow plug relay coil open
- Open kickout fuse
Checks
- 1Check the kickout fuse in the start aid circuit for continuity with a meter.
- 2Test the relay coil resistance with the relay removed.
- 3Clean and secure the circuit connectors, then run open and short tests.
- 4Replace the relay or harness as the tests show.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Cat CID 2417 FMI 05Start aid (ether) solenoid current low
The engine ECM sees low current in the output to the ether injection solenoid, so the cold-start aid cannot be energised. The 924H manual calls this the start aid circuit.· Open circuitOpen circuitCheck soonCauses
- High resistance or open in the engine harness
- High resistance or open in the rear frame harness
- Start aid solenoid open
Checks
- 1Remove the ether bottle if fitted, then test the solenoid coil resistance with a multimeter.
- 2Check the connector at the solenoid for corrosion and a seated terminal.
- 3Run the start aid test in Cat ET and listen for the solenoid.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Shared checks
Checks, in order
- 1Measure battery voltage at rest and with the engine at idle and high idle to see the real system voltage.
- 2Run the start aid override test in Cat ET and listen for the relay or solenoid.
- 3Clean and tighten both battery terminals and the ground strap to the frame.
- 4Check the start aid fuse for continuity.
- 5Inspect the alternator belt for glazing and tension.
- 6Clean and secure the connectors in the circuit.
- 7Run the charging system test in Cat ET and compare alternator output.
Causes
- Key switch contacts worn or intermittent
- Worn or loose alternator belt
- Open wiring in the engine or frame harness
- Start relay or its wiring shorted high
Most common here: erratic or implausible (4 of 10)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: A warning lamp on the cluster, dimming lights, hard starting or random resets of the display and controls.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 168 FMI 00)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 168 FMI 01)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 168 FMI 02)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 168 FMI 04)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 444 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E875)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E876)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1834 FMI 02)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 2246 FMI 05)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 2417 FMI 05)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
