Bobcat · Electrical
Bobcat Rear work, marker, tail, stop and plate lamps fault codes
The rear work lights, marker and side lights, tail lights, stop lamp and registration plate lamp are each switched through their own controller output and fuse. A code names the lamp and whether its circuit is shorted to ground or battery, open, or driven the wrong way.
Where this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
What do these codes mean?
Bobcat codes B1034-12 to B1039-13 are all about the rear work, marker, tail, stop and plate lamps. The most common failure type is shorted low (6 of 13); none needs an immediate stop. Start with this check: walk round the machine with the lights on and note which rear lamps are actually out before testing wiring.
How urgent are they?
None of the 13 codes here means stop now; all 13 can wait until the shift ends, but find the cause before the next one.
- Check soon13
What should I check first?
Walk round the machine with the lights on and note which rear lamps are actually out before testing wiring.
Shared checks13 of 13
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Bobcat B1034-12Rear work lights error on
The controller sees the rear work lights switched on when it was commanded off, so the work lights stay on. The driver, relay or wiring is holding it on. Rear work lights usually share one feed, so both lamps dark points to the feed and one dark points to that lamp.· OtherOtherCheck soonCauses
- Output wire shorted to a live supply
- Relay or driver stuck closed
- Controller output stage failed and cannot switch off
Checks
- 1Unplug the rear work lights at the rear lamp connector on the rear frame with the key on; if the controller still reads it on, the fault is in the wiring or controller.
- 2Check the output wire for contact with a power wire along its run.
- 3Listen and feel for the lamp and its socket energising while it should be off.
- 4Switch the work lights on at the panel and see whether both lamps light, then swap the two lamp plugs to see whether the fault follows the lamp or the wiring.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1034-14Rear work lights error off
The controller sees the rear work lights off when it was commanded on, so the rear work lights stay dark. The circuit is open, shorted to ground or not being driven. Rear work lights usually share one feed, so both lamps dark points to the feed and one dark points to that lamp.· Shorted lowShorted lowCheck soonCauses
- Open or grounded output wire
- The lamp and its socket failed open
- Blown fuse or missing supply to the circuit
Checks
- 1Check the fuse and supply to the rear work lights circuit with the key on.
- 2Measure the resistance of the lamp and its socket and look for an open or a short to its body.
- 3Command the function and measure voltage at the rear work lights plug; none means a wiring or controller fault.
- 4Switch the work lights on at the panel and see whether both lamps light, then swap the two lamp plugs to see whether the fault follows the lamp or the wiring.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1035-12Rear marker light short to battery
The controller reads the rear marker light circuit tied to battery voltage when it should only be switched by the controller. It shuts the output off to protect its driver, so the marker or side lights stay dark. Marker and side lamps are low-power circuits, so a bulb of the wrong rating can set these codes.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through at the rear lamp plug and touching a live supply wire
- Water or corrosion in the plug bridging a pin to a power pin
- Controller output stage failed shorted to supply
Checks
- 1Unplug the rear marker light at the rear lamp plug and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
- 2Trace the wire back from the lamp and its socket for chafing next to live supply wires and for melted insulation.
- 3Replace the lamp and its socket only if the wire reads clean and the part itself reads shorted.
- 4Switch the lights to the road position and look at each marker and side lamp from outside the machine, since a single dim lamp can set the code.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1035-14Rear marker light short to ground or open circuit
The controller cannot tell whether the rear marker light circuit is shorted to ground or open, because both read the same on this output, so the marker or side lights stay dark. Marker and side lamps are low-power circuits, so a bulb of the wrong rating can set these codes.· Shorted lowShorted lowCheck soonCauses
- Wire broken or pin backed out at the rear lamp plug
- Wire chafed to the frame
- The lamp and its socket failed open or shorted
Checks
- 1Unplug the rear marker light and measure the output wire to ground; a reading near zero is a short, infinite resistance at the part is an open.
- 2Check the connector at the rear lamp plug for pushed-back pins before measuring.
- 3Measure the resistance of the lamp and its socket with the plug off and compare with a new part's specification.
- 4Switch the lights to the road position and look at each marker and side lamp from outside the machine, since a single dim lamp can set the code.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1036-12Rear tail lights error on
The controller sees the rear tail lights switched on when it was commanded off, so the tail lights stay on. The driver, relay or wiring is holding it on. Tail lamps are on whenever the light switch is in the road position, so check both sides together.· OtherOtherCheck soonCauses
- Output wire shorted to a live supply
- Relay or driver stuck closed
- Controller output stage failed and cannot switch off
Checks
- 1Unplug the rear tail lights at the rear lamp plug with the key on; if the controller still reads it on, the fault is in the wiring or controller.
- 2Check the output wire for contact with a power wire along its run.
- 3Listen and feel for the lamp and its socket energising while it should be off.
- 4Check the tail lamp bulbs are the correct wattage, because a bulb that is too small or too large changes the current the controller sees.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1036-14Rear tail lights error off
The controller sees the rear tail lights off when it was commanded on, so the tail lights stay dark. The circuit is open, shorted to ground or not being driven. Tail lamps are on whenever the light switch is in the road position, so check both sides together.· Shorted lowShorted lowCheck soonCauses
- Open or grounded output wire
- The lamp and its socket failed open
- Blown fuse or missing supply to the circuit
Checks
- 1Check the fuse and supply to the rear tail lights circuit with the key on.
- 2Measure the resistance of the lamp and its socket and look for an open or a short to its body.
- 3Command the function and measure voltage at the rear tail lights plug; none means a wiring or controller fault.
- 4Check the tail lamp bulbs are the correct wattage, because a bulb that is too small or too large changes the current the controller sees.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1037-12Stop lamp short to battery
The controller reads the stop lamp circuit tied to battery voltage when it should only be switched by the controller. It shuts the output off to protect its driver, so the brake light does not light. The stop lamp is driven by the brake switch input, so press the brake and watch the lamp and the switch state.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through at the stop lamp plug and touching a live supply wire
- Water or corrosion in the plug bridging a pin to a power pin
- Controller output stage failed shorted to supply
Checks
- 1Unplug the stop lamp at the stop lamp plug and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
- 2Trace the wire back from the lamp and its socket for chafing next to live supply wires and for melted insulation.
- 3Replace the lamp and its socket only if the wire reads clean and the part itself reads shorted.
- 4Press the brake pedal with an assistant at the rear and confirm the stop lamps light on both sides before testing the circuit.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1037-14Stop lamp short to ground or open circuit
The controller cannot tell whether the stop lamp circuit is shorted to ground or open, because both read the same on this output, so the brake light does not light. The stop lamp is driven by the brake switch input, so press the brake and watch the lamp and the switch state.· Shorted lowShorted lowCheck soonCauses
- Wire broken or pin backed out at the stop lamp plug
- Wire chafed to the frame
- The lamp and its socket failed open or shorted
Checks
- 1Unplug the stop lamp and measure the output wire to ground; a reading near zero is a short, infinite resistance at the part is an open.
- 2Check the connector at the stop lamp plug for pushed-back pins before measuring.
- 3Measure the resistance of the lamp and its socket with the plug off and compare with a new part's specification.
- 4Press the brake pedal with an assistant at the rear and confirm the stop lamps light on both sides before testing the circuit.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1038-12Registration plate lamp short to battery
The controller reads the registration plate lamp circuit tied to battery voltage when it should only be switched by the controller. It shuts the output off to protect its driver, so the plate lamp stays dark. The plate lamp is a small separate circuit near the rear of the machine, often with its own fuse.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through at the plate lamp connector and touching a live supply wire
- Water or corrosion in the plug bridging a pin to a power pin
- Controller output stage failed shorted to supply
Checks
- 1Unplug the registration plate lamp at the plate lamp connector and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
- 2Trace the wire back from the lamp and its socket for chafing next to live supply wires and for melted insulation.
- 3Replace the lamp and its socket only if the wire reads clean and the part itself reads shorted.
- 4Open the plate lamp housing and check for water, corrosion and a loose earth lead, which are the usual causes on this small circuit.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1038-14Registration plate lamp short to ground or open circuit
The controller cannot tell whether the registration plate lamp circuit is shorted to ground or open, because both read the same on this output, so the plate lamp stays dark. The plate lamp is a small separate circuit near the rear of the machine, often with its own fuse.· Shorted lowShorted lowCheck soonCauses
- Wire broken or pin backed out at the plate lamp connector
- Wire chafed to the frame
- The lamp and its socket failed open or shorted
Checks
- 1Unplug the registration plate lamp and measure the output wire to ground; a reading near zero is a short, infinite resistance at the part is an open.
- 2Check the connector at the plate lamp connector for pushed-back pins before measuring.
- 3Measure the resistance of the lamp and its socket with the plug off and compare with a new part's specification.
- 4Open the plate lamp housing and check for water, corrosion and a loose earth lead, which are the usual causes on this small circuit.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1039-11Side lights short to ground
The controller reads the side lights circuit pulled to ground, so it cannot drive the load. The output is shut off and the marker or side lights stay dark until the short is cleared. Marker and side lamps are low-power circuits, so a bulb of the wrong rating can set these codes.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket at the rear lamp plug
- The lamp and its socket shorted to its housing
- Water in the connector or a pin touching the shell
Checks
- 1With the plug off, test the side lights output wire to chassis ground; a reading near zero shows a harness short.
- 2Measure from each pin of the lamp and its socket to its body; any continuity means the part itself is shorted.
- 3Look for harness sections crushed under clamps or cut by sharp edges at the rear lamp plug.
- 4Switch the lights to the road position and look at each marker and side lamp from outside the machine, since a single dim lamp can set the code.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1039-12Side lights short to battery
The controller reads the side lights circuit tied to battery voltage when it should only be switched by the controller. It shuts the output off to protect its driver, so the marker or side lights stay dark. Marker and side lamps are low-power circuits, so a bulb of the wrong rating can set these codes.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through at the rear lamp plug and touching a live supply wire
- Water or corrosion in the plug bridging a pin to a power pin
- Controller output stage failed shorted to supply
Checks
- 1Unplug the side lights at the rear lamp plug and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
- 2Trace the wire back from the lamp and its socket for chafing next to live supply wires and for melted insulation.
- 3Replace the lamp and its socket only if the wire reads clean and the part itself reads shorted.
- 4Switch the lights to the road position and look at each marker and side lamp from outside the machine, since a single dim lamp can set the code.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1039-13Side lights not connected
The controller sees an open circuit on the side lights, so no current can flow through it and the marker or side lights stay dark. The break is in the wire, the connector or the part itself. Marker and side lamps are low-power circuits, so a bulb of the wrong rating can set these codes.· Open circuitOpen circuitCheck soonCauses
- Pin backed out of the connector or plug not latched at the rear lamp plug
- Wire broken inside its insulation near a bend or clamp
- The lamp and its socket burnt open or its internal lead broken
Checks
- 1Check that the side lights connector at the rear lamp plug is fully seated and its lock tab engaged.
- 2Measure the resistance of the lamp and its socket with the plug off; an infinite reading confirms an open.
- 3Check continuity of each wire from the side lights plug back to the controller connector, flexing the harness as you go.
- 4Switch the lights to the road position and look at each marker and side lamp from outside the machine, since a single dim lamp can set the code.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Shared checks
Checks, in order
- 1Walk round the machine with the lights on and note which rear lamps are actually out before testing wiring.
- 2Open the lamp connector and look for water, burnt pins and corrosion, then clean and reseat it.
- 3Measure voltage at the lamp plug with the circuit on; voltage present with no light means the lamp or its earth.
- 4Measure the lamp wire to ground with the plug off; a low reading shows a short in the harness.
- 5Check the fuse for that lamp circuit and confirm the replacement bulb has the correct rating.
Causes
- Lamp unit failed open or fitted with the wrong rating
- Rear harness crushed or chafed at the frame joint
- Water in a lamp connector causing a short or leakage
- Lamp earth lead loose or corroded
Most common here: shorted low (6 of 13)
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
When to stop
You'll notice: One rear lamp is out or stays lit, the stop lamp fails a road check, or a lamp warning shows on the panel.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
