Bobcat · Electrical
Bobcat Front work, road lights and turn signals fault codes
The front work lights, the left and right road lights and the turn signals are switched by controller outputs or relays. A code names the lamp or relay and whether the circuit is shorted to ground, shorted to battery, open or driven the wrong way.
Where this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
What do these codes mean?
Bobcat codes B116F-11 to M5028 are all about the front work, road lights and turn signals. The most common failure type is shorted low (8 of 22); none needs an immediate stop. Start with this check: check the bulb or lamp unit first; a failed lamp is the commonest reason for an open-circuit code.
How urgent are they?
None of the 22 codes here means stop now; all 22 can wait until the shift ends, but find the cause before the next one.
- Check soon22
What should I check first?
Check the bulb or lamp unit first; a failed lamp is the commonest reason for an open-circuit code.
Shared checks22 of 22
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Bobcat B116F-11Front left road light short to ground
The controller reads the front road light circuit pulled to ground, so it cannot drive the load. The output is shut off and that front road light stays dark, which fails a road check until the short is cleared.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket at the lamp connector behind the front frame
- The lamp and its socket shorted to its housing
- Water in the connector or a pin touching the shell
Checks
- 1With the plug off, test the front road light output wire to chassis ground; a reading near zero shows a harness short.
- 2Measure from each pin of the lamp and its socket to its body; any continuity means the part itself is shorted.
- 3Look for harness sections crushed under clamps or cut by sharp edges at the lamp connector behind the front frame.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B116F-12Front left road light short to battery
The controller reads the front road light circuit tied to battery voltage when it should only be switched by the controller. It shuts the output off to protect its driver, so that front road light stays dark, which fails a road check.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through at the lamp connector behind the front frame and touching a live supply wire
- Water or corrosion in the plug bridging a pin to a power pin
- Controller output stage failed shorted to supply
Checks
- 1Unplug the front road light at the lamp connector behind the front frame and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
- 2Trace the wire back from the lamp and its socket for chafing next to live supply wires and for melted insulation.
- 3Replace the lamp and its socket only if the wire reads clean and the part itself reads shorted.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B116F-13Front left road light open circuit
The controller sees an open circuit on the front road light, so no current can flow through it and that front road light stays dark, which fails a road check. The break is in the wire, the connector or the part itself.· Open circuitOpen circuitCheck soonCauses
- Pin backed out of the connector or plug not latched at the lamp connector behind the front frame
- Wire broken inside its insulation near a bend or clamp
- The lamp and its socket burnt open or its internal lead broken
Checks
- 1Check that the front road light connector at the lamp connector behind the front frame is fully seated and its lock tab engaged.
- 2Measure the resistance of the lamp and its socket with the plug off; an infinite reading confirms an open.
- 3Check continuity of each wire from the front road light plug back to the controller connector, flexing the harness as you go.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Bobcat B117F-11Front right road light short to ground
Front right road light short to ground: same fault as B116F-11 (the circuit reads pulled to ground), here on the front right road light.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket
- The lamp and its socket shorted to its housing
Checks
- 1Test the front right road light output wire to chassis ground with the plug off.
- 2Test steps: see B116F-11.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B117F-12Front right road light short to battery
Front right road light short to battery: same fault as B116F-12 (the circuit reads tied to battery voltage), here on the front right road light.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through
- Water or corrosion in the plug bridging a pin to a power pin
Checks
- 1Unplug the front right road light and look for voltage on its output wire with the key on.
- 2Test steps: see B116F-12.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B117F-13Front right road light open circuit
Front right road light open circuit: same fault as B116F-13 (the circuit is open), here on the front right road light.· Open circuitOpen circuitCheck soonCauses
- Pin backed out of the connector or plug not latched
- Wire broken inside its insulation
Checks
- 1Check the front right road light connector is seated, then measure across the part for an open.
- 2Test steps: see B116F-13.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Bobcat B1030-11Front work light (left side) short to ground
The controller reads the front work light circuit pulled to ground, so it cannot drive the load. The output is shut off and that front work light does not come on until the short is cleared.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket at the lamp connector on the cab roof or lift arm
- The lamp and its socket shorted to its housing
- Water in the connector or a pin touching the shell
Checks
- 1With the plug off, test the front work light output wire to chassis ground; a reading near zero shows a harness short.
- 2Measure from each pin of the lamp and its socket to its body; any continuity means the part itself is shorted.
- 3Look for harness sections crushed under clamps or cut by sharp edges at the lamp connector on the cab roof or lift arm.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1030-12Front work light (left side) short to battery
The controller reads the front work light circuit tied to battery voltage when it should only be switched by the controller. It shuts the output off to protect its driver, so that front work light does not come on.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through at the lamp connector on the cab roof or lift arm and touching a live supply wire
- Water or corrosion in the plug bridging a pin to a power pin
- Controller output stage failed shorted to supply
Checks
- 1Unplug the front work light at the lamp connector on the cab roof or lift arm and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
- 2Trace the wire back from the lamp and its socket for chafing next to live supply wires and for melted insulation.
- 3Replace the lamp and its socket only if the wire reads clean and the part itself reads shorted.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1030-13Front work light (left side) not connected
The controller sees an open circuit on the front work light, so no current can flow through it and that front work light does not come on. The break is in the wire, the connector or the part itself.· Open circuitOpen circuitCheck soonCauses
- Pin backed out of the connector or plug not latched at the lamp connector on the cab roof or lift arm
- Wire broken inside its insulation near a bend or clamp
- The lamp and its socket burnt open or its internal lead broken
Checks
- 1Check that the front work light connector at the lamp connector on the cab roof or lift arm is fully seated and its lock tab engaged.
- 2Measure the resistance of the lamp and its socket with the plug off; an infinite reading confirms an open.
- 3Check continuity of each wire from the front work light plug back to the controller connector, flexing the harness as you go.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Bobcat B1031-11Front work light (right side) short to ground
Front work light (right side) short to ground: same fault as B1030-11 (the circuit reads pulled to ground), here on the front work light right side.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket
- The lamp and its socket shorted to its housing
Checks
- 1Test the front work light right side output wire to chassis ground with the plug off.
- 2Test steps: see B1030-11.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1031-12Front work light (right side) short to battery
Front work light (right side) short to battery: same fault as B1030-12 (the circuit reads tied to battery voltage), here on the front work light right side.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through
- Water or corrosion in the plug bridging a pin to a power pin
Checks
- 1Unplug the front work light right side and look for voltage on its output wire with the key on.
- 2Test steps: see B1030-12.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1031-13Front work light (right side) not connected
Front work light (right side) not connected: same fault as B1030-13 (the circuit is open), here on the front work light right side.· Open circuitOpen circuitCheck soonCauses
- Pin backed out of the connector or plug not latched
- Wire broken inside its insulation
Checks
- 1Check the front work light right side connector is seated, then measure across the part for an open.
- 2Test steps: see B1030-13.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Bobcat B1177-12Left turn signal short to battery
The controller reads the turn signal circuit tied to battery voltage when it should only be switched by the controller. It shuts the output off to protect its driver, so that turn signal does not flash.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through at the signal lamp connector and touching a live supply wire
- Water or corrosion in the plug bridging a pin to a power pin
- Controller output stage failed shorted to supply
Checks
- 1Unplug the turn signal at the signal lamp connector and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
- 2Trace the wire back from the signal lamp and flasher output for chafing next to live supply wires and for melted insulation.
- 3Replace the signal lamp and flasher output only if the wire reads clean and the part itself reads shorted.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1177-14Left turn signal short to ground or open circuit
The controller cannot tell whether the turn signal circuit is shorted to ground or open, because both read the same on this output, so that turn signal does not flash.· Shorted lowShorted lowCheck soonCauses
- Wire broken or pin backed out at the signal lamp connector
- Wire chafed to the frame
- The signal lamp and flasher output failed open or shorted
Checks
- 1Unplug the turn signal and measure the output wire to ground; a reading near zero is a short, infinite resistance at the part is an open.
- 2Check the connector at the signal lamp connector for pushed-back pins before measuring.
- 3Measure the resistance of the signal lamp and flasher output with the plug off and compare with a new part's specification.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1187-12Right turn signal short to battery
Right turn signal short to battery: same fault as B1177-12 (the circuit reads tied to battery voltage), here on the right turn signal.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through
- Water or corrosion in the plug bridging a pin to a power pin
Checks
- 1Unplug the right turn signal and look for voltage on its output wire with the key on.
- 2Test steps: see B1177-12.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1187-14Right turn signal short to ground or open circuit
Right turn signal short to ground or open circuit: same fault as B1177-14 (the circuit reads shorted to ground or open), here on the right turn signal.· Shorted lowShorted lowCheck soonCauses
- Wire broken or pin backed out
- Wire chafed to the frame
Checks
- 1Unplug the right turn signal and measure the wire to ground, then across the part for an open.
- 2Test steps: see B1177-14.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat M4802Front light relay error on
The controller sees the front light relay switched on when it was commanded off, so the lights stay on. The driver, relay or wiring is holding it on.· OtherOtherCheck soonCauses
- Output wire shorted to a live supply
- Relay or driver stuck closed
- Controller output stage failed and cannot switch off
Checks
- 1Unplug the front light relay at the front light relay socket with the key on; if the controller still reads it on, the fault is in the wiring or controller.
- 2Check the output wire for contact with a power wire along its run.
- 3Listen and feel for the relay and its socket energising while it should be off.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M4803Front light relay error off
The controller sees the front light relay off when it was commanded on, so the front lights do not switch. The circuit is open, shorted to ground or not being driven.· Shorted lowShorted lowCheck soonCauses
- Open or grounded output wire
- The relay and its socket failed open
- Blown fuse or missing supply to the circuit
Checks
- 1Check the fuse and supply to the front light relay circuit with the key on.
- 2Measure the resistance of the relay and its socket and look for an open or a short to its body.
- 3Command the function and measure voltage at the front light relay plug; none means a wiring or controller fault.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat M5002Front light output error on
The controller sees the front light output switched on when it was commanded off, so the lights stay on. The driver, relay or wiring is holding it on.· OtherOtherCheck soonCauses
- Output wire shorted to a live supply
- Relay or driver stuck closed
- Controller output stage failed and cannot switch off
Checks
- 1Unplug the front light output at the front light output connector with the key on; if the controller still reads it on, the fault is in the wiring or controller.
- 2Check the output wire for contact with a power wire along its run.
- 3Listen and feel for the lamp feed energising while it should be off.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M5003Front light output error off
The controller sees the front light output off when it was commanded on, so the front lights do not switch as commanded. The circuit is open, shorted to ground or not being driven.· Shorted lowShorted lowCheck soonCauses
- Open or grounded output wire
- The lamp feed failed open
- Blown fuse or missing supply to the circuit
Checks
- 1Check the fuse and supply to the front light output circuit with the key on.
- 2Measure the resistance of the lamp feed and look for an open or a short to its body.
- 3Command the function and measure voltage at the front light output plug; none means a wiring or controller fault.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat M5007Front light output open circuit
The controller sees an open circuit on the front light output, so no current can flow through it and the front lights do not switch as commanded. The break is in the wire, the connector or the part itself.· Open circuitOpen circuitCheck soonCauses
- Pin backed out of the connector or plug not latched at the front light output connector
- Wire broken inside its insulation near a bend or clamp
- The lamp feed burnt open or its internal lead broken
Checks
- 1Check that the front light output connector at the front light output connector is fully seated and its lock tab engaged.
- 2Measure the resistance of the lamp feed with the plug off; an infinite reading confirms an open.
- 3Check continuity of each wire from the front light output plug back to the controller connector, flexing the harness as you go.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Bobcat M5028Front light output failure
The controller reports a failure on the front light output without saying whether it is open, shorted or stuck, so the front lights do not switch as commanded. It is a general output fault rather than one failure mode.· OtherOtherCheck soonCauses
- Driver damaged by an earlier short or overload
- Corroded or loose connector at the front light output connector
- Intermittent break in the harness
- Controller output stage failed
Checks
- 1Read the other active codes for the front light output; a short or open code beside this one narrows the cause.
- 2Reseat the connector at the front light output connector and clear the code to see whether it returns.
- 3Measure voltage at the plug while the output is commanded to see whether the controller drives it at all.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Check the bulb or lamp unit first; a failed lamp is the commonest reason for an open-circuit code.
- 2Unplug the lamp connector and inspect for water and burnt pins before testing the wiring.
- 3Measure voltage at the lamp plug with the switch on; no voltage means a relay, fuse or wiring fault upstream.
- 4Check the lamp wire to ground with the plug off; a low reading shows a short in the harness.
- 5Swap the light relay with an identical one when the code reads error on or error off.
Causes
- Bulb or LED unit failed open
- Harness chafed at the lift arm or cab pillar
- Water in the lamp connector
- Light relay stuck or its output driver failed
Most common here: shorted low (8 of 22)
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
When to stop
You'll notice: A front light or signal does not work, stays on, or blows its fuse, and a lamp warning shows on the panel.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
