EF Logo

Bobcat · Electrical

Bobcat Horn, buzzer, backup alarm, wipers and washer fault codes

The horn, buzzer and backup alarm, the backup lamp relay and the wiper and washer motors are driven by cab controller outputs. A code names the output and whether its circuit is shorted, open or stuck on or off.

FaultCheckVRY002-05Bobcat · Horn, buzzer, backup alarm, wipers and washer
Code shows hereFAULTVRY002-05

Where this code shows

On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.

What do these codes mean?

Bobcat codes VRY002-05 to D7566 are all about the horn, buzzer, backup alarm, wipers and washer. The most common failure type is shorted low (7 of 15); none needs an immediate stop. Start with this check: operate the function from its cab switch and listen for the relay click, the motor or the alarm.

How urgent are they?

None of the 15 codes here means stop now; all 15 can wait until the shift ends, but find the cause before the next one.

  • Check soon15

What should I check first?

Operate the function from its cab switch and listen for the relay click, the motor or the alarm.

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Bobcat VRY002-05Back buzzer relay, current below normal

    The controller measured less current than expected through the back buzzer relay while commanding it, which usually means an open wire, a poor connection or a coil that has failed open, so the buzzer or backup alarm does not sound.· Open circuit
    Check soon

    Causes

    • Coil open or very high resistance
    • Connector pin backed out or corroded at the alarm connector near the rear of the cab
    • Wire broken near a bend
    • Controller output weak

    Checks

    1. 1Measure the resistance of the alarm with the plug off; an open or very high reading confirms the part.
    2. 2Check the back buzzer relay connector at the alarm connector near the rear of the cab for corrosion and for pins pushed back in the shell.
    3. 3Check the wire for resistance between the controller and the plug while flexing the harness.
    4. 4Select reverse with the machine blocked safely and listen for the alarm, and check the alarm unit is firmly bolted and earthed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat VRY002-06Back buzzer relay, current above normal

    The controller measured more current than expected through the back buzzer relay while commanding it, which points to a shorted coil or a wire shorted to ground, and the buzzer or backup alarm does not sound until it is cleared.· Shorted low
    Check soon

    Causes

    • Coil shorted between turns
    • Wire chafed to ground at the alarm connector near the rear of the cab
    • Water in the connector
    • Wrong part fitted

    Checks

    1. 1Measure the resistance of the alarm with the plug off and compare it with a matching part.
    2. 2Test the back buzzer relay output wire to ground with the plug off for a short.
    3. 3Look at the harness at the alarm connector near the rear of the cab for chafing that shorts to ground only when the machine moves.
    4. 4Select reverse with the machine blocked safely and listen for the alarm, and check the alarm unit is firmly bolted and earthed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat VRY003-05Backup lamp relay, current below normal

    The controller measured less current than expected through the backup lamp relay while commanding it, which usually means an open wire, a poor connection or a coil that has failed open, so the backup lamp or alarm does not operate.· Open circuit
    Check soon

    Causes

    • Coil open or very high resistance
    • Connector pin backed out or corroded at the relay socket
    • Wire broken near a bend
    • Controller output weak

    Checks

    1. 1Measure the resistance of the relay with the plug off; an open or very high reading confirms the part.
    2. 2Check the backup lamp relay connector at the relay socket for corrosion and for pins pushed back in the shell.
    3. 3Check the wire for resistance between the controller and the plug while flexing the harness.
    4. 4Swap the relay with an identical one from the panel and select reverse again to see whether the symptom moves.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat VRY003-06Backup lamp relay, current above normal

    The controller measured more current than expected through the backup lamp relay while commanding it, which points to a shorted coil or a wire shorted to ground, and the backup lamp or alarm does not operate until it is cleared.· Shorted low
    Check soon

    Causes

    • Coil shorted between turns
    • Wire chafed to ground at the relay socket
    • Water in the connector
    • Wrong part fitted

    Checks

    1. 1Measure the resistance of the relay with the plug off and compare it with a matching part.
    2. 2Test the backup lamp relay output wire to ground with the plug off for a short.
    3. 3Look at the harness at the relay socket for chafing that shorts to ground only when the machine moves.
    4. 4Swap the relay with an identical one from the panel and select reverse again to see whether the symptom moves.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat B10A0-12Wiper output short to battery

    The controller reads the wiper output circuit tied to battery voltage when it should only be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through at the wiper motor connector on the cab and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the wiper output at the wiper motor connector on the cab and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
    2. 2Trace the wire back from the motor for chafing next to live supply wires and for melted insulation.
    3. 3Replace the motor only if the wire reads clean and the part itself reads shorted.
    4. 4Run the wiper at each speed and press the washer switch, and check the wiper arm is not blocked by a seized pivot.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat B10A0-14Wiper output short to ground or open circuit

    The controller cannot tell whether the wiper output circuit is shorted to ground or open, because both read the same on this output, so the wiper or washer does not run.· Shorted low
    Check soon

    Causes

    • Wire broken or pin backed out at the wiper motor connector on the cab
    • Wire chafed to the frame
    • The motor failed open or shorted

    Checks

    1. 1Unplug the wiper output and measure the output wire to ground; a reading near zero is a short, infinite resistance at the part is an open.
    2. 2Check the connector at the wiper motor connector on the cab for pushed-back pins before measuring.
    3. 3Measure the resistance of the motor with the plug off and compare with a new part's specification.
    4. 4Run the wiper at each speed and press the washer switch, and check the wiper arm is not blocked by a seized pivot.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat B10A1-12Washer fluid output short to battery

    The controller reads the washer fluid output circuit tied to battery voltage when it should only be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through at the wiper motor connector on the cab and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the washer fluid output at the wiper motor connector on the cab and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
    2. 2Trace the wire back from the motor for chafing next to live supply wires and for melted insulation.
    3. 3Replace the motor only if the wire reads clean and the part itself reads shorted.
    4. 4Run the wiper at each speed and press the washer switch, and check the wiper arm is not blocked by a seized pivot.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat B10A1-14Washer fluid output short to ground or open circuit

    The controller cannot tell whether the washer fluid output circuit is shorted to ground or open, because both read the same on this output, so the wiper or washer does not run.· Shorted low
    Check soon

    Causes

    • Wire broken or pin backed out at the wiper motor connector on the cab
    • Wire chafed to the frame
    • The motor failed open or shorted

    Checks

    1. 1Unplug the washer fluid output and measure the output wire to ground; a reading near zero is a short, infinite resistance at the part is an open.
    2. 2Check the connector at the wiper motor connector on the cab for pushed-back pins before measuring.
    3. 3Measure the resistance of the motor with the plug off and compare with a new part's specification.
    4. 4Run the wiper at each speed and press the washer switch, and check the wiper arm is not blocked by a seized pivot.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat B1040-14Buzzer error off

    The controller sees the buzzer off when it was commanded on, so the buzzer or backup alarm does not sound.· Shorted low
    Check soon

    Causes

    • Open or grounded output wire
    • The alarm failed open
    • Blown fuse or missing supply to the circuit

    Checks

    1. 1Check the fuse and supply to the buzzer circuit with the key on.
    2. 2Measure the resistance of the alarm and look for an open or a short to its body.
    3. 3Command the function and measure voltage at the buzzer plug; none means a wiring or controller fault.
    4. 4Select reverse with the machine blocked safely and listen for the alarm, and check the alarm unit is firmly bolted and earthed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat B1041-12Backup alarm error on

    The controller sees the backup alarm switched on when it was commanded off, so the alarm sounds continuously.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed
    • Controller output stage failed and cannot switch off

    Checks

    1. 1Unplug the backup alarm at the alarm connector near the rear of the cab with the key on; if the controller still reads it on, the fault is in the wiring or controller.
    2. 2Check the output wire for contact with a power wire along its run.
    3. 3Listen and feel for the alarm energising while it should be off.
    4. 4Select reverse with the machine blocked safely and listen for the alarm, and check the alarm unit is firmly bolted and earthed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat B1041-14Backup alarm error off

    The controller sees the backup alarm off when it was commanded on, so the buzzer or backup alarm does not sound.· Shorted low
    Check soon

    Causes

    • Open or grounded output wire
    • The alarm failed open
    • Blown fuse or missing supply to the circuit

    Checks

    1. 1Check the fuse and supply to the backup alarm circuit with the key on.
    2. 2Measure the resistance of the alarm and look for an open or a short to its body.
    3. 3Command the function and measure voltage at the backup alarm plug; none means a wiring or controller fault.
    4. 4Select reverse with the machine blocked safely and listen for the alarm, and check the alarm unit is firmly bolted and earthed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat B1042-12Horn relay short to battery

    The controller reads the horn relay circuit tied to battery voltage when it should only be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through at the horn relay socket and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the horn relay at the horn relay socket and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
    2. 2Trace the wire back from the relay and horn for chafing next to live supply wires and for melted insulation.
    3. 3Replace the relay and horn only if the wire reads clean and the part itself reads shorted.
    4. 4Press the horn button while listening at the relay; a click with no horn points to the horn unit, no click points upstream.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat B1042-14Horn relay short to ground or open circuit

    The controller cannot tell whether the horn relay circuit is shorted to ground or open, because both read the same on this output, so the horn does not sound.· Shorted low
    Check soon

    Causes

    • Wire broken or pin backed out at the horn relay socket
    • Wire chafed to the frame
    • The relay and horn failed open or shorted

    Checks

    1. 1Unplug the horn relay and measure the output wire to ground; a reading near zero is a short, infinite resistance at the part is an open.
    2. 2Check the connector at the horn relay socket for pushed-back pins before measuring.
    3. 3Measure the resistance of the relay and horn with the plug off and compare with a new part's specification.
    4. 4Press the horn button while listening at the relay; a click with no horn points to the horn unit, no click points upstream.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7552Drive backup alarm error on

    Drive backup alarm error on: same fault as B1041-12 (the output reads on when it should be off), here on the backup alarm.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed

    Checks

    1. 1Unplug the backup alarm with the key on and see whether the controller still reads it on.
    2. 2Test steps: see B1041-12.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7566Drive backup alarm error off

    Drive backup alarm error off: same fault as B1041-14 (the output reads off when it was commanded on), here on the backup alarm.· Other
    Check soon

    Causes

    • Open or grounded output wire
    • The alarm failed open

    Checks

    1. 1Check the fuse and the supply voltage at the backup alarm plug with the output commanded.
    2. 2Test steps: see B1041-14.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Operate the function from its cab switch and listen for the relay click, the motor or the alarm.
  2. 2Check the fuse for that circuit and measure voltage at the component plug while it is commanded.
  3. 3Swap the relay with an identical one and see whether the symptom moves.
  4. 4Check the wiper arm and pivot are free and the washer pump has fluid.
  5. 5Inspect the cab harness at the door pillar for pinched or broken wires.

Causes

  • Horn, buzzer or alarm unit failed
  • Relay stuck or its socket loose
  • Wiper or washer motor failed or its pivot seized
  • Cab harness broken where the door or pillar flexes

Most common here: shorted low (7 of 15)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: The horn or alarm does not sound, sounds continuously, or the wipers and washer do not run.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.