EF Logo

Bobcat · Drive

Bobcat Brakes, two-speed and drive speed sensors fault codes

The brake pull and hold solenoids and their relays release and apply the parking brake, the two-speed solenoids shift the drive motors to high range, and the left and right speed sensors report drive speed to the controller. A code names the part and the failure.

FaultCheckM2006Bobcat · Brakes, two-speed and drive speed sensors
Code shows hereFAULTM2006

Where this code shows

On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.

What do these codes mean?

Bobcat codes 20-02 to D7596 are all about the brakes, two-speed and drive speed sensors. The most common failure type is shorted high (9 of 42); none needs an immediate stop. Start with this check: command the function and listen for the brake or two-speed solenoid to click; no click with voltage at the plug points to the coil.

How urgent are they?

None of the 42 codes here means stop now; all 42 can wait until the shift ends, but find the cause before the next one.

  • Check soon42

What should I check first?

Command the function and listen for the brake or two-speed solenoid to click; no click with voltage at the plug points to the coil.

Shared checks

42 of 42

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Bobcat 20-02Two-speed solenoid error ON

    The controller sees the two-speed solenoid energised when it has commanded it off.· Other
    Check soon

    Causes

    • Coil or valve stuck on
    • Output wire to the two-speed solenoid touching a live feed along the harness at the pump-mounted speed valve plug, which runs close to the hot pump housings
    • Wiring cross-connected to another output

    Checks

    1. 1Check the harness at the pump-mounted speed valve plug, which runs close to the hot pump housings for rubbed insulation touching a live wire
    2. 2Check for a speed valve spool stuck by dirt, which can hold the function on even with the coil off
    3. 3With the two-speed solenoid unplugged and the output commanded off, check for voltage on the output pin; any voltage shows a stuck driver or a short to a live wire
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat 20-03Two-speed solenoid error OFF

    The controller sees the two-speed solenoid not energised when it has commanded it on.· Other
    Check soon

    Causes

    • Blown fuse on the two-speed solenoid feed
    • Broken wire or loose plug
    • Speed valve spool slow to move because of dirty oil

    Checks

    1. 1Check the wiring along the harness at the pump-mounted speed valve plug, which runs close to the hot pump housings for continuity and for pins pushed back out of their housings
    2. 2Check for a speed valve spool stuck by dirt, which can make the coil draw wrongly
    3. 3Check the fuse that supplies the two-speed solenoid circuit and replace it if blown, then look for the cause
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat 37-02Two-speed secondary error on

    The controller sees the two-speed secondary switched on when it was commanded off.· Shorted high
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck on
    • Controller output stage failed

    Checks

    1. 1Unplug the two-speed secondary with the key on; if the controller still reads it on, the fault is in the wiring or controller
    2. 2Check the output wire for contact with a power wire along its run
    3. 3Listen and feel for the part energising while it should be off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat 37-03Two-speed secondary error off

    The controller sees the two-speed secondary off when it was commanded on.· Shorted low
    Check soon

    Causes

    • Open or grounded output wire
    • Coil or element failed
    • Blown fuse or missing supply to the circuit

    Checks

    1. 1Check the fuse and supply to the two-speed secondary circuit with the key on
    2. 2Measure the resistance of the part and look for an open or a short to its body
    3. 3Command the function and measure voltage at the plug; none means a wiring or controller fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C1030-00Two speed shift not allowed

    The controller logged the message "Two speed shift not allowed".· Other
    Check soon

    Causes

    • Condition the message names is active
    • Wiring or connector problem on the related part
    • Software or programming mismatch

    Checks

    1. 1Read the message in context with any other active code
    2. 2Check the related part and its plug for damage
    3. 3Clear the code and see whether it returns
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C1032-11Brake pull output short to ground

    The controller reads the brake pull output circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • Coil or element shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the output wire to chassis ground; a reading near zero shows a harness short
    2. 2Measure from each coil pin to the body of the brake pull output; any continuity means the part is shorted
    3. 3Look for harness sections crushed under clamps or cut by sharp edges near the brake pull output
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C1032-12Brake pull output short to battery

    The controller reads the brake pull output circuit as tied to battery voltage when it should be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the brake pull output and check the output wire for voltage with the key on; any voltage with the load removed is a short to supply
    2. 2Trace the wire along the harness for chafing next to live supply wires and for melted insulation
    3. 3Replace the brake pull output only if the wire reads clean and the coil or element itself reads shorted
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat C1032-13Brake pull output open circuit

    The controller sees an open circuit on the brake pull output, meaning no current can flow through it.· Open circuit
    Check soon

    Causes

    • Pin backed out of the connector or plug not latched
    • Wire broken inside its insulation near a bend or clamp
    • Coil or element burnt open

    Checks

    1. 1Check the connector at the brake pull output is fully seated and its lock tab engaged
    2. 2Measure the resistance across the part with the plug off; infinite resistance confirms an open
    3. 3Check continuity of each wire from the plug back to the controller connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat C1033-11Left brake hold output short to ground

    The controller reads the left brake hold output circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • Coil or element shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the output wire to chassis ground; a reading near zero shows a harness short
    2. 2Measure from each coil pin to the body of the left brake hold output; any continuity means the part is shorted
    3. 3Look for harness sections crushed under clamps or cut by sharp edges near the left brake hold output
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C1033-12Left brake hold output short to battery

    The controller reads the left brake hold output circuit as tied to battery voltage when it should be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the left brake hold output and check the output wire for voltage with the key on; any voltage with the load removed is a short to supply
    2. 2Trace the wire along the harness for chafing next to live supply wires and for melted insulation
    3. 3Replace the left brake hold output only if the wire reads clean and the coil or element itself reads shorted
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat C1033-13Left brake hold output open circuit

    The controller sees an open circuit on the left brake hold output, meaning no current can flow through it.· Open circuit
    Check soon

    Causes

    • Pin backed out of the connector or plug not latched
    • Wire broken inside its insulation near a bend or clamp
    • Coil or element burnt open

    Checks

    1. 1Check the connector at the left brake hold output is fully seated and its lock tab engaged
    2. 2Measure the resistance across the part with the plug off; infinite resistance confirms an open
    3. 3Check continuity of each wire from the plug back to the controller connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat C1034-11Right brake hold output short to ground

    The controller reads the right brake hold output circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • Coil or element shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the output wire to chassis ground; a reading near zero shows a harness short
    2. 2Measure from each coil pin to the body of the right brake hold output; any continuity means the part is shorted
    3. 3Look for harness sections crushed under clamps or cut by sharp edges near the right brake hold output
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C1034-12Right brake hold output short to battery

    The controller reads the right brake hold output circuit as tied to battery voltage when it should be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the right brake hold output and check the output wire for voltage with the key on; any voltage with the load removed is a short to supply
    2. 2Trace the wire along the harness for chafing next to live supply wires and for melted insulation
    3. 3Replace the right brake hold output only if the wire reads clean and the coil or element itself reads shorted
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat C1034-13Right brake hold output open circuit

    The controller sees an open circuit on the right brake hold output, meaning no current can flow through it.· Open circuit
    Check soon

    Causes

    • Pin backed out of the connector or plug not latched
    • Wire broken inside its insulation near a bend or clamp
    • Coil or element burnt open

    Checks

    1. 1Check the connector at the right brake hold output is fully seated and its lock tab engaged
    2. 2Measure the resistance across the part with the plug off; infinite resistance confirms an open
    3. 3Check continuity of each wire from the plug back to the controller connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat C1035-16Left brake pull relay error off

    The controller sees the left brake pull relay off when it was commanded on.· Shorted low
    Check soon

    Causes

    • Open or grounded output wire
    • Coil or element failed
    • Blown fuse or missing supply to the circuit

    Checks

    1. 1Check the fuse and supply to the left brake pull relay circuit with the key on
    2. 2Measure the resistance of the part and look for an open or a short to its body
    3. 3Command the function and measure voltage at the plug; none means a wiring or controller fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C1035-17Left brake pull relay error on

    The controller sees the left brake pull relay switched on when it was commanded off.· Shorted high
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck on
    • Controller output stage failed

    Checks

    1. 1Unplug the left brake pull relay with the key on; if the controller still reads it on, the fault is in the wiring or controller
    2. 2Check the output wire for contact with a power wire along its run
    3. 3Listen and feel for the part energising while it should be off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat C1036-16Right brake pull relay error off

    The controller sees the right brake pull relay off when it was commanded on.· Shorted low
    Check soon

    Causes

    • Open or grounded output wire
    • Coil or element failed
    • Blown fuse or missing supply to the circuit

    Checks

    1. 1Check the fuse and supply to the right brake pull relay circuit with the key on
    2. 2Measure the resistance of the part and look for an open or a short to its body
    3. 3Command the function and measure voltage at the plug; none means a wiring or controller fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C1036-17Right brake pull relay error on

    The controller sees the right brake pull relay switched on when it was commanded off.· Shorted high
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck on
    • Controller output stage failed

    Checks

    1. 1Unplug the right brake pull relay with the key on; if the controller still reads it on, the fault is in the wiring or controller
    2. 2Check the output wire for contact with a power wire along its run
    3. 3Listen and feel for the part energising while it should be off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat C1051-11Two speed solenoid short to ground

    The controller reads the two speed solenoid circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • Coil or element shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the output wire to chassis ground; a reading near zero shows a harness short
    2. 2Measure from each coil pin to the body of the two speed solenoid; any continuity means the part is shorted
    3. 3Look for harness sections crushed under clamps or cut by sharp edges near the two speed solenoid
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C1051-12Two speed solenoid short to battery

    The controller reads the two speed solenoid circuit as tied to battery voltage when it should be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the two speed solenoid and check the output wire for voltage with the key on; any voltage with the load removed is a short to supply
    2. 2Trace the wire along the harness for chafing next to live supply wires and for melted insulation
    3. 3Replace the two speed solenoid only if the wire reads clean and the coil or element itself reads shorted
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat C1051-13Two speed solenoid open circuit

    The controller sees an open circuit on the two speed solenoid, meaning no current can flow through it.· Open circuit
    Check soon

    Causes

    • Pin backed out of the connector or plug not latched
    • Wire broken inside its insulation near a bend or clamp
    • Coil or element burnt open

    Checks

    1. 1Check the connector at the two speed solenoid is fully seated and its lock tab engaged
    2. 2Measure the resistance across the part with the plug off; infinite resistance confirms an open
    3. 3Check continuity of each wire from the plug back to the controller connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat C1051-19Two speed solenoid overcurrent

    The controller measured too much current on the two speed solenoid output and switched it off to protect its driver.· Real condition
    Check soon

    Causes

    • Coil shorted between turns so it draws too much current
    • Wiring partly shorted to ground
    • Wrong or damaged part fitted that loads the output

    Checks

    1. 1Measure the coil resistance of the two speed solenoid with the plug off and compare with a matching part on the same machine
    2. 2Check the wire for a partial short to ground that only shows when the machine is hot or vibrating
    3. 3Replace the part and clear the code; if it returns at once, suspect the controller output
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Bobcat M2005Two-speed primary solenoid short to battery

    The two-speed primary solenoid output is shorted to battery voltage, so the controller cannot switch the circuit properly.· Shorted high
    Check soon

    Causes

    • Moisture bridging the plug pins
    • Two-speed solenoid output wire touching a live supply on the drive speed valve at the hydrostatic pumps
    • Two-speed solenoid winding shorted internally, often from a speed valve spool stuck by dirt

    Checks

    1. 1Follow the harness at the pump-mounted speed valve plug, which runs close to the hot pump housings looking for melted or rubbed insulation next to supply wires
    2. 2Dry and clean the plug and re-seat it, and read the other drive codes to see whether other outputs are affected
    3. 3With the two-speed solenoid unplugged and the key on, check its output wire for voltage; any voltage while the output is off shows a short to supply
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat M2006Two-speed primary solenoid short to ground

    The two-speed primary solenoid output is shorted to ground, so the coil will not energise correctly.· Shorted low
    Check soon

    Causes

    • Moisture inside the two-speed solenoid connector
    • Coil insulation breakdown
    • Chafed output wire touching the frame on the drive speed valve at the hydrostatic pumps
    • Harness crushed at a bracket or clamp
    • Speed valve spool slow to move because of dirty oil

    Checks

    1. 1With the plug off, test the two-speed solenoid output wire to chassis ground; a reading near zero shows a harness short to ground
    2. 2Trace the wire through the harness at the pump-mounted speed valve plug, which runs close to the hot pump housings, looking for rubs and sections crushed under clamps
    3. 3Check that the harness clips are in place and not cutting into the wire; compare with the other drive codes
    4. 4Check resistance from each coil pin to the valve body; any continuity means the coil has failed
    5. 5Check the drive motor case and pump area for leaks and heat, since a sticking speed valve usually comes with dirty or old oil
    6. 6Replace the coil or repair the wire, then clear the code and test: select high range and travel on level ground; the machine should speed up and drop back when low range is selected
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat M2007Two-speed primary solenoid open circuit

    The two-speed primary solenoid output circuit is open.· Open circuit
    Check soon

    Causes

    • Wire broken inside the insulation on the drive speed valve at the hydrostatic pumps
    • Speed valve spool slow to move because of dirty oil
    • Loose or corroded terminal in the plug

    Checks

    1. 1Look at the terminals inside the plug for corrosion, spread contacts or a loose crimp; read the other drive codes for related faults
    2. 2Check the fuse for the two-speed solenoid circuit and confirm it is the right rating
    3. 3Check the supply and return wires of the two-speed solenoid for continuity, flexing the harness at the pump-mounted speed valve plug, which runs close to the hot pump housings as you test
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat M2032Two-speed primary overcurrent

    The two-speed primary solenoid output is drawing too much current.· Other
    Check soon

    Causes

    • Output wire chafed to ground on the drive speed valve at the hydrostatic pumps
    • Dirt or moisture in the plug
    • Partly shorted two-speed solenoid coil, often from a speed valve spool stuck by dirt

    Checks

    1. 1Inspect the harness at the pump-mounted speed valve plug, which runs close to the hot pump housings for damage that could create a partial short to ground
    2. 2Open the plug and look for water, dirt or melted plastic that points to heat in the circuit
    3. 3Look for a speed valve spool stuck by dirt, which can overload the output and trip the current limit
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat M3705Two speed secondary short to battery

    The controller reads the two speed secondary circuit as tied to battery voltage when it should be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the two speed secondary and check the output wire for voltage with the key on; any voltage with the load removed is a short to supply
    2. 2Trace the wire along the harness for chafing next to live supply wires and for melted insulation
    3. 3Replace the two speed secondary only if the wire reads clean and the coil or element itself reads shorted
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat M3706Two speed secondary short to ground

    The controller reads the two speed secondary circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • Coil or element shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the output wire to chassis ground; a reading near zero shows a harness short
    2. 2Measure from each coil pin to the body of the two speed secondary; any continuity means the part is shorted
    3. 3Look for harness sections crushed under clamps or cut by sharp edges near the two speed secondary
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat M3707Two speed secondary open circuit

    The controller sees an open circuit on the two speed secondary, meaning no current can flow through it.· Open circuit
    Check soon

    Causes

    • Pin backed out of the connector or plug not latched
    • Wire broken inside its insulation near a bend or clamp
    • Coil or element burnt open

    Checks

    1. 1Check the connector at the two speed secondary is fully seated and its lock tab engaged
    2. 2Measure the resistance across the part with the plug off; infinite resistance confirms an open
    3. 3Check continuity of each wire from the plug back to the controller connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat M3732Two speed secondary overcurrent

    The controller measured too much current on the two speed secondary output and switched it off to protect its driver.· Real condition
    Check soon

    Causes

    • Coil shorted between turns so it draws too much current
    • Wiring partly shorted to ground
    • Wrong or damaged part fitted that loads the output

    Checks

    1. 1Measure the coil resistance of the two speed secondary with the plug off and compare with a matching part on the same machine
    2. 2Check the wire for a partial short to ground that only shows when the machine is hot or vibrating
    3. 3Replace the part and clear the code; if it returns at once, suspect the controller output
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Bobcat D7511Drive left speed sensor not connected

    The controller reports the drive left speed sensor as not connected.· Open circuit
    Check soon

    Causes

    • Plug off or not latched
    • Pin pushed out of the connector body
    • Wire broken near the part

    Checks

    1. 1Look at the plug on the drive left speed sensor and reseat it until the lock clicks
    2. 2Check each pin in the plug for push-out or bent contacts
    3. 3Test continuity of the wires between the plug and the controller
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat D7512Drive right speed sensor not connected

    The controller reports the drive right speed sensor as not connected.· Open circuit
    Check soon

    Causes

    • Plug off or not latched
    • Pin pushed out of the connector body
    • Wire broken near the part

    Checks

    1. 1Look at the plug on the drive right speed sensor and reseat it until the lock clicks
    2. 2Check each pin in the plug for push-out or bent contacts
    3. 3Test continuity of the wires between the plug and the controller
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat D7574Drive right wheel speed uncommanded motion

    The controller reports a performance problem on the drive right wheel speed, such as reduced response, wrong direction, uncommanded motion or a position that cannot be reached.· Other
    Check soon

    Causes

    • Worn or sticking part
    • Low supply voltage or poor ground
    • Calibration out of date

    Checks

    1. 1Check the drive right wheel speed moves freely and without binding
    2. 2Check supply voltage and ground at its plug
    3. 3Recalibrate if the manual allows and retest
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7575Drive left wheel speed uncommanded motion

    The controller reports a performance problem on the drive left wheel speed, such as reduced response, wrong direction, uncommanded motion or a position that cannot be reached.· Other
    Check soon

    Causes

    • Worn or sticking part
    • Low supply voltage or poor ground
    • Calibration out of date

    Checks

    1. 1Check the drive left wheel speed moves freely and without binding
    2. 2Check supply voltage and ground at its plug
    3. 3Recalibrate if the manual allows and retest
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7577Drive left speed sensor out of range high

    The drive left speed sensor signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· Other
    Check soon

    Causes

    • Signal wire shorted to supply
    • Open sensor ground giving a floating high signal
    • Sensor failed high

    Checks

    1. 1Check the ground wire of the drive left speed sensor for continuity
    2. 2Look at the live reading on the display and see if it sits at the top of its scale
    3. 3Test the signal wire for stray voltage with the plug off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7578Drive right speed sensor out of range high

    The drive right speed sensor signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· Other
    Check soon

    Causes

    • Signal wire shorted to supply
    • Open sensor ground giving a floating high signal
    • Sensor failed high

    Checks

    1. 1Check the ground wire of the drive right speed sensor for continuity
    2. 2Look at the live reading on the display and see if it sits at the top of its scale
    3. 3Test the signal wire for stray voltage with the plug off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7579Drive left speed sensor out of range low

    The drive left speed sensor signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Open signal wire or missing supply
    • Sensor failed low

    Checks

    1. 1Check the supply voltage at the drive left speed sensor plug with the key on
    2. 2Look at the live reading on the display and see if it sits at the bottom of its scale
    3. 3Test the signal wire to ground with the plug off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7580Drive right speed sensor out of range low

    The drive right speed sensor signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Open signal wire or missing supply
    • Sensor failed low

    Checks

    1. 1Check the supply voltage at the drive right speed sensor plug with the key on
    2. 2Look at the live reading on the display and see if it sits at the bottom of its scale
    3. 3Test the signal wire to ground with the plug off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7593Drive unresponsive right speed sensor

    The controller logged the message "Drive unresponsive right speed sensor".· Other
    Check soon

    Causes

    • Condition the message names is active
    • Wiring or connector problem on the related part
    • Software or programming mismatch

    Checks

    1. 1Read the message in context with any other active code
    2. 2Check the related part and its plug for damage
    3. 3Clear the code and see whether it returns
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7594Drive unresponsive left speed sensor

    The controller logged the message "Drive unresponsive left speed sensor".· Other
    Check soon

    Causes

    • Condition the message names is active
    • Wiring or connector problem on the related part
    • Software or programming mismatch

    Checks

    1. 1Read the message in context with any other active code
    2. 2Check the related part and its plug for damage
    3. 3Clear the code and see whether it returns
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7595Drive left speed sensor reverse direction

    The drive left speed sensor moves the opposite way to the command, or its direction is reversed.· Other
    Check soon

    Causes

    • Sensor wires or connector swapped
    • Sensor fitted the wrong way round
    • Wrong calibration

    Checks

    1. 1Check the connector and wire colours against the schematic
    2. 2Recalibrate after correcting any swap
    3. 3Check the sensor orientation
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7596Drive right speed sensor reverse direction

    The drive right speed sensor moves the opposite way to the command, or its direction is reversed.· Other
    Check soon

    Causes

    • Sensor wires or connector swapped
    • Sensor fitted the wrong way round
    • Wrong calibration

    Checks

    1. 1Check the connector and wire colours against the schematic
    2. 2Recalibrate after correcting any swap
    3. 3Check the sensor orientation
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Command the function and listen for the brake or two-speed solenoid to click; no click with voltage at the plug points to the coil.
  2. 2Swap a brake relay with an identical one and see whether a relay code moves to the other circuit.
  3. 3Measure each solenoid coil with the plug off and compare with the matching one.
  4. 4Check the speed sensor mounting, air gap and connector, and look for metal debris on the sensor tip.
  5. 5Inspect the harness near the drive motors for heat and crush damage.

Causes

  • Brake or two-speed solenoid coil shorted or open
  • Brake relay stuck or its socket loose
  • Speed sensor gap wrong, connector loose or tone ring damaged
  • Harness chafed near the drive motor or axle

Most common here: shorted high (9 of 42)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: The brake will not release or will not hold, high speed range will not engage, or the speed reading is wrong or missing.

Brake and steering faults are a safety issue on site. Chock the machine and keep it parked until the fault is found and the brakes are tested.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.