EF Logo

Equipment transport height and weight calculator for lowbeds and flatbeds

Before a machine goes on a trailer, check that the loaded height and the gross weight are inside the limits for the route. Enter your own limits; the tool shows the clearance or the excess.

The formula

Height = machine height + deck height. Gross weight = machine + truck and trailer.

What it works out

Add the machine and the trailer deck and compare the totals with height and weight limits.

Why it matters

An over-height or overweight load is stopped at the road or on the bridge, not at the yard.

How to use it

  1. Enter the Machine Transport Height in m, from the spec sheet with the boom folded, and the Trailer Deck Height with the load on.
  2. Enter the Height Limit that applies to your route or permit.
  3. Enter the Machine Weight with its attachments and fuel, and the weight of the Truck and Trailer empty.
  4. Enter the Gross Weight Limit. Read the Total Height, the Height Clearance and the Gross Combination Weight with the weight margin.

Quick reference

Printable chart

Loaded height by machine transport height (1 m deck, 4.5 m limit)

Machine height (m)Loaded height (m)Clearance (m)Over height (m)
2.53.5 m1 m0 m
34 m0.5 m0 m
3.24.2 m0.3 m0 m
3.54.5 m0 m0 m
3.84.8 m-0.3 m0.3 m
45 m-0.5 m0.5 m

A trailer deck at 1.0 m and a limit of 4.5 m.

The calculation

Total height = machine transport height + deck height of the trailer with the load on it. Clearance = limit − total height. Gross combination weight = machine weight + weight of the truck and trailer. Margin = limit − gross weight. A negative clearance or margin is shown as an over-height or overweight figure.

Typical values and your limit

The limits depend on the road, the emirate or country, the type of vehicle and any permit, and they change. Heights of around 4.5 m for a loaded vehicle are commonly quoted in the Gulf, and many bridges and tunnels are signed lower; this is a typical figure only, not legal advice. Confirm the limit and the route with the traffic authority or the haulier, and enter that. A lowbed deck is typically about 0.9 to 1.1 m loaded, a flatbed about 1.3 to 1.6 m.

Getting the numbers right

Use the transport height, not the working height, and measure the highest point: a cab, the ROPS or FOPS, an exhaust stack, a beacon or a folded boom. A machine can often be lowered by folding the boom and arm and removing or folding the beacon and the cab roof guard. Include the attachments, counterweight and fuel in the weight, and weigh the truck and trailer rather than trusting the spec sheet. Axle loads need checking too; this tool covers the total only.

Worked examples

  • A 22 t excavator, 3.1 m high, on a 1 m lowbed is 4.1 m tall, leaving 0.4 m to a 4.5 m limit. The combination weighs 46 t, with 19 t to spare against 65 t.
  • A 3.6 m machine on a 1.5 m flatbed is 5.1 m, which is over height by 0.6 m. Moving it to a lowbed fixes it.
  • A 42 t machine with a 26 t truck and trailer gives 68 t gross, which is overweight by 3 t against a 65 t limit, so it needs a permit or a lighter set-up.

Frequently asked questions

What is the maximum height for a truck in the UAE?

About 4.5 m is commonly quoted for a loaded vehicle, but it varies by road and permit. Confirm with the authority and enter the limit that applies.

How do I calculate the loaded height on a lowbed?

Add the machine’s transport height to the height of the trailer deck with the load on. Add any packing or ramps under the tracks.

Do I need a permit for an over-height or overweight load?

Usually yes, with a route, escort and times set by the authority. Ask the haulier early because permits take time.

How can I reduce the transport height of an excavator?

Fold the boom and stick as the manual shows, remove or fold the beacon and any cab guard, and use a lowbed trailer.

Does this check axle loads?

No. It checks total height and total weight only. Ask the haulier to confirm the axle loads on the route.

Add this calculator to your website

Copy the code and paste it into your page. The calculator is free and works as it does here.

<iframe src="https://www.equipmentsfinder.com/embed/field-tools/equipment-transport-height-calculator" title="Equipment transport height and weight calculator for lowbeds and flatbeds" width="100%" height="620" style="border:0;max-width:720px" loading="lazy"></iframe>
<p style="font-size:12px"><a href="https://www.equipmentsfinder.com/field-tools/equipment-transport-height-calculator">Equipment transport height and weight calculator for lowbeds and flatbeds</a> by <a href="https://www.equipmentsfinder.com">EquipmentsFinder</a></p>
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.