EF Logo

Detroit · EGR system

Detroit Exhaust flap actuator (SRA4 / EGF) fault codes

The exhaust flap (EGF) is driven by the smart remote actuator SRA4. These codes cover its communication, supply voltage, learn span, position and frozen-valve faults.

FaultCheckSPN 8151FMI 1Detroit · Exhaust flap actuator (SRA4 / EGF)
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.

What do these codes mean?

Detroit codes SPN 8151 FMI 1 to SPN 521170 FMI 31 are all about the exhaust flap actuator (SRA4 / EGF). The most common failure type is real condition (5 of 14); none needs an immediate stop. Start with this check: check the SRA4 connector, the supply and the ground at the actuator.

How urgent are they?

None of the 14 codes here means stop now; all 14 can wait until the shift ends, but find the cause before the next one.

  • Check soon14

What should I check first?

Check the SRA4 connector, the supply and the ground at the actuator.

Shared checks

14 of 14

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Detroit SPN 8151 FMI 1Exhaust Gas Flap Stuck Open

    Detroit lists SPN 8151 FMI 1 as "Exhaust Gas Flap Stuck Open".· Real condition
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3The exhaust flap is stuck open; check the flap and SRA4 for carbon and movement.
    4. 4The flap is stuck open: check the flap shaft for carbon and the actuator response.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 521162 FMI 0Smart Remote Actuator 4 (EGF), Temperature Alert

    Detroit lists SPN 521162 FMI 0 as "Smart Remote Actuator 4 (EGF), Temperature Alert".· Real condition
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3The SRA4 temperature is too high; check the exhaust heat around the actuator.
    4. 4SRA4 is overheating: check the heat shield and the exhaust leaks near the actuator.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 521163 FMI 9Lost communication with SRA4

    Detroit lists SPN 521163 FMI 9 as "Lost communication with SRA4".· Lost message
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3Communication with SRA4 is lost; check the actuator supply and CAN wires.
    4. 4SRA4 communication lost: check the CAN wires and the supply.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 521164 FMI 9Smart Remote Actuator 4, Communication Error

    Same failure as SPN 521163 FMI 9 ("Lost communication with SRA4") on a sibling part: Detroit lists SPN 521164 FMI 9 as "Smart Remote Actuator 4, Communication Error".· Lost message
    Check soon

    Causes

    • The causes listed under SPN 521163 FMI 9, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 521163 FMI 9, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 521170 FMI 2Smart Remote Actuator 4 (EGF), Position Deviation Error

    Detroit lists SPN 521170 FMI 2 as "Smart Remote Actuator 4 (EGF), Position Deviation Error".· Erratic or implausible
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3The flap position deviates from the command; check the flap for sticking.
    4. 4The flap position does not follow the command; check the flap for carbon.
    5. 5Position deviation on the flap is checked against the actuator feedback, so test the commanded travel with the exhaust cold to avoid heat effects on the readings.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 521170 FMI 3Smart Remote Actuator 4 (EGF), Low or High Supply Voltage

    Detroit lists SPN 521170 FMI 3 as "Smart Remote Actuator 4 (EGF), Low or High Supply Voltage".· Shorted high
    Check soon

    Causes

    • Output wire of the exhaust flap actuator rubbed through and touching a live wire
    • Internal short in the exhaust flap actuator

    Checks

    1. 1Unplug the exhaust flap actuator and look for voltage on the output wire with the key on.
    2. 2Measure the exhaust flap actuator winding resistance and compare it with a good unit.
    3. 3The SRA4 supply voltage is out of range; measure the supply at the connector.
    4. 4The SRA4 supply is out of range; measure it at the connector while the flap moves.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 521170 FMI 7Smart Remote Actuator 4 (EGF), Failsafe Mode, Motor Off

    Detroit lists SPN 521170 FMI 7 as "Smart Remote Actuator 4 (EGF), Failsafe Mode, Motor Off".· Part or controller
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3SRA4 is in failsafe with the motor off; check the supply and the flap.
    4. 4SRA4 is in failsafe with the motor off; check the supply and the flap.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 521170 FMI 9Smart Remote Actuator 4, No Communication

    Same failure as SPN 521163 FMI 9 ("Lost communication with SRA4") on a sibling part: Detroit lists SPN 521170 FMI 9 as "Smart Remote Actuator 4, No Communication".· Lost message
    Check soon

    Causes

    • The causes listed under SPN 521163 FMI 9, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 521163 FMI 9, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 521170 FMI 11Smart Remote Actuator 4 (EGF), Learn Command Pending

    Detroit lists SPN 521170 FMI 11 as "Smart Remote Actuator 4 (EGF), Learn Command Pending".· Other
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3An SRA4 learn command is pending; run the learn in the tool.
    4. 4A learn is pending for SRA4; run the learn with the tool.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Detroit SPN 521170 FMI 12Smart Remote Actuator 4 (EGF), Valve Frozen

    Detroit lists SPN 521170 FMI 12 as "Smart Remote Actuator 4 (EGF), Valve Frozen".· Part or controller
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3The flap valve is frozen; check for carbon and free movement.
    4. 4The flap is frozen; remove it and turn the shaft by hand.
    5. 5The exhaust flap is exposed to hot exhaust gas, so a frozen flap is usually seized by deposits; do not force it, because the shaft and the actuator gear can break.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 521170 FMI 13Smart Remote Actuator 4 (EGF), Calibration Error

    Detroit lists SPN 521170 FMI 13 as "Smart Remote Actuator 4 (EGF), Calibration Error".· Part or controller
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3The SRA4 calibration is in error; redo the calibration.
    4. 4SRA4 calibration error; relearn the end positions.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 521170 FMI 16Smart Remote Actuator 4 (EGF), Learn Span too High

    Detroit lists SPN 521170 FMI 16 as "Smart Remote Actuator 4 (EGF), Learn Span too High".· Real condition
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3The SRA4 learn span is too high; check the linkage and the flap travel.
    4. 4The learn span is too high; check the flap linkage and travel.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 521170 FMI 18Smart Remote Actuator 4 (EGF), Learn Span too Small

    Detroit lists SPN 521170 FMI 18 as "Smart Remote Actuator 4 (EGF), Learn Span too Small".· Real condition
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3The SRA4 learn span is too small; check for carbon limiting travel.
    4. 4The learn span is too small; look for carbon limiting the flap.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 521170 FMI 31Smart Remote Actuator 4 (EGF), Learn Span Incomplete

    Detroit lists SPN 521170 FMI 31 as "Smart Remote Actuator 4 (EGF), Learn Span Incomplete".· Real condition
    Check soon

    Causes

    • Wiring, supply or mechanical problem on the exhaust flap actuator
    • Controller output fault

    Checks

    1. 1Read the freeze-frame data for this code and note the engine state.
    2. 2Command the exhaust flap actuator in the tool and watch the result.
    3. 3The SRA4 learn span is incomplete; repeat the learn.
    4. 4The learn span is incomplete; repeat the learn.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Check the SRA4 connector, the supply and the ground at the actuator.
  2. 2Inspect the CAN wiring to the actuator for chafing and corrosion.
  3. 3Run the actuator learn routine in the tool and watch the result.
  4. 4Remove the flap and check for carbon build-up and free movement.

Causes

  • Actuator communication lost through damaged wiring
  • Low supply voltage at the actuator
  • Flap seized with carbon or damaged
  • Failed actuator electronics

Most common here: real condition (5 of 14)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: Reduced power, slow warm-up and a check-engine lamp; the flap may stay in a failsafe position.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.