Volvo/Mack · MID 130 transmission ECU
Volvo/Mack Fault Code MID 130 PID 33 FMI 2
Clutch position sensor signals disagree
What does Volvo/Mack code MID 130 PID 33 FMI 2 mean?
The two clutch position signals from the clutch cylinder sensor (SEPoC and its inverted partner SEPoCINV) differ too much while both are inside the normal range. The control unit cannot trust the clutch position. Urgency: check soon - the machine may derate or limit a function. Check first: read the two clutch position signals in the scan tool with the clutch moving; they should mirror each other.
- MID 130
- Which control unit reports it
- PID 33
- Parameter at fault
- FMI 2
- Erratic or incorrect data
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the two clutch position signals in the scan tool with the clutch moving; they should mirror each other
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Clutch cylinder position sensor failing or drifting
- Poor connection in the sensor plug at the clutch actuator
- Damaged wiring between the sensor and the transmission control unit
How it failed
You'll notice: Yellow lamp is sent, the clutch acts slowly, starts feel rough and gear changes are slow, especially at crawl speed.
Erratic or implausibleRead from FMI 2: erratic or incorrect data
The reading jumps, drifts or disagrees with the sensors around it.
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Clutch position sensor
- MID 130 PID 33 FMI 2Clutch position sensor signals disagreeErratic or implausibleCheck soon
- MID 130 PID 33 FMI 3Clutch position sensor signal shorted highShorted highCheck soon
- MID 130 PID 33 FMI 5Clutch position sensor open circuitOpen circuitCheck soon
- MID 130 PID 33 FMI 13Clutch position sensor not calibratedPart or controllerStop now
Other Volvo/Mack codes: MID 130 transmission ECU
- MID 130 PSID 1 FMI 3PWM valve quick engagement shorted high
- MID 130 PSID 1 FMI 5PWM valve quick engagement open circuit
- MID 130 PSID 22 FMI 3Counter shaft brake valve shorted high - brake applied
- MID 130 PSID 25 FMI 11First gear cannot engage
- MID 130 PSID 25 FMI 12Reverse gear cannot engage
- MID 130 PSID 27 FMI 0Clutch disengages unintentionally
Related on Equipments Finder
Source
This source lists MID 130 PID 33 FMI 2 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack CHU, CXU, GU and TD trucks with the mDRIVE automated transmission (MID 130 transmission control unit).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
