EF Logo

Volvo/Mack · MID 144 vehicle ECU

Volvo/Mack Idle validation switches fault codes

The idle validation switches confirm that the accelerator pedal is at idle. The vehicle ECU compares them with the pedal signal.

FaultCheckMID 144PSID 2FMI 7Volvo/Mack · Idle validation switches
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 144 PSID 2 FMI 7 and MID 144 SID 230 FMI 7 are all about the idle validation switches. Most are part or controller faults; none needs an immediate stop. Start with this check: read both idle validation switches on the scan tool and see that they change state with the pedal.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Read both idle validation switches on the scan tool and see that they change state with the pedal

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 144 PSID 2 FMI 7Idle validation switch 2 reads wrong

    The reading from idle validation switch 2 (IVS2) is faulty and does not agree with the accelerator pedal position.· Part or controller
    Check soon

    Causes

    • Idle validation switch (IVS)
    • IVS connector
    • IVS harness

    Checks

    1. 1Compare the IVS2 state with the pedal in the scan tool as you press the pedal
    2. 2Check the IVS connector for corrosion and loose pins
    3. 3Check the pedal harness for opens and shorts for damage, corrosion or looseness
    4. 4Replace the pedal assembly if the harness tests good
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Volvo/Mack MID 144 SID 230 FMI 7Idle validation switch 1 reads wrong

    The reading from idle validation switch 1 (IVS1) does not agree with the pedal.· Part or controller
    Check soon

    Causes

    • Idle validation switch (IVS) fault
    • IVS connector fault
    • IVS harness fault
    • Loss of ground to the accelerator pedal sensor

    Checks

    1. 1Compare the pedal reading with the IVS state in the scan tool as you press the pedal
    2. 2Check the pedal ground circuit for continuity
    3. 3Check the IVS connector for corrosion and loose pins
    4. 4Replace the pedal assembly if the circuit tests good
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

Shared checks

Checks, in order

  1. 1Read both idle validation switches on the scan tool and see that they change state with the pedal
  2. 2Check the pedal connector and wiring for corrosion, chafing and loose pins along the run to the ECU
  3. 3Check the pedal movement by hand for sticking, a broken return spring or a loose mounting
  4. 4Replace the pedal assembly if the switch is faulty

Causes

  • Switch failed in the pedal
  • Damaged wiring
  • Pedal assembly worn

Most codes here: part or controller (2 of 2)

Check power and ground at the module connector with the key on, then its fuses.

When to stop

You'll notice: The engine idles only or does not respond to the pedal, and a check lamp comes on.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.