Thermo King · Engine ECU faults (SR-2/SR-3/SR-4)
Thermo King Engine ECU internal faults, enable signals and run relays fault codes
This page covers ECU internal faults, enable and run signals, and the run and shutdown relay circuits of the unit. The engine ECU needs an enable signal and a run signal from the controller and runs self-tests.
More about these partsLess
The controller switches the run relay and watches the shutdown circuit.
Where this code shows
Press the alarm key or open the Alarms menu on the controller display to list active alarms.
What do these codes mean?
Thermo King codes 35 to 899 are all about the engine ECU internal faults, enable signals and run relays. 2 need an immediate stop. Start with this check: check the enable and run signal wires and plugs between controller and ECU.
How urgent are they?
2 of 12 codes here mean stop now; 9 can wait until the shift ends, but find the cause before the next one; 1 is information only.
- Stop now2
- Check soon9
- Info1
What should I check first?
Check the enable and run signal wires and plugs between controller and ECU
Shared checks12 of 12
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Thermo King 35Check run relay circuit
The controller found a problem with the run relay circuit that feeds power to the fuel solenoid and engine run circuits.· OtherOtherStop nowCauses
- Run relay coil or contacts failed
- Blown fuse in the run circuit
- Wire from relay to fuel solenoid open
Checks
- 1Check the run circuit fuse and replace it if blown
- 2Listen and test the relay for pull-in when run is commanded
- 3Measure voltage at the fuel solenoid with run active
- 4Check the relay socket terminals for burnt or spread pins that cause a poor contact
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 51Check shutdown circuit
The controller found an issue in the shutdown circuit that cuts the fuel or run power to stop the engine.· OtherOtherStop nowCauses
- Fuel solenoid hold circuit fault
- Run relay failure
- Wiring short in the shutdown line
Checks
- 1Check the shutdown wire for shorts to supply or ground
- 2Test the fuel solenoid hold and pull-in coils
- 3Check the run relay pulls in and releases correctly when the unit starts and stops
- 4Test the related fuses for continuity and check their holders for heat damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 509ECU failed to enable
The engine ECU did not switch on when the controller asked it to. The engine cannot be started until the enable signal works.· OtherOtherCheck soonCauses
- Enable wire open or shorted
- ECU supply fuse or relay failed
Checks
- 1Check the ECU enable wire and its fuse
- 2Check the ECU main relay and supply voltage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 510ECU run signal failed
The run signal between the controller and the engine ECU failed while the engine was meant to run. The engine may stop or fail to start.· OtherOtherCheck soonCauses
- Run signal wire open or shorted
- Connector problem at the ECU
Checks
- 1Check the run signal wire and plug
- 2Monitor the run signal while cranking
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 540Illegal engine operating state
The engine ECU or controller found the engine in a state that should not be possible, for example running without a request. The unit may stop.· OtherOtherCheck soonCauses
- Faulty enable or run signal
- ECU software fault
Checks
- 1Check the enable and run signal wiring
- 2Cycle the unit power and see whether the alarm returns
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 599Engine service tool connected
A service tool is connected to the engine ECU. The unit may run in a limited mode while the tool is plugged in.· OtherOtherInfoCauses
- Diagnostic tool left plugged in
- Faulty connector
Checks
- 1Disconnect the service tool and restart the unit
- 2Check the diagnostic connector for a stuck pin
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 617Internal ECU fault
The engine ECU detected a fault inside itself. Engine operation can be limited or the engine may not start.· Lost messageLost messageCheck soonCauses
- ECU internal failure
- Unstable supply voltage
Checks
- 1Check the battery voltage and ECU fuses
- 2Read the stored ECU codes with the service tool
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Thermo King 699Unknown ECU fault
The engine ECU reported a fault code the controller does not know. The ECU should be read with a service tool to find what it reported.· OtherOtherCheck soonCauses
- New ECU fault not listed in the controller
- Software mismatch
Checks
- 1Read the ECU fault codes with the service tool
- 2Compare the ECU and controller software versions
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 836Major ECU failures
The engine ECU reports a serious internal failure. Engine operation is usually limited or stopped.· OtherOtherCheck soonCauses
- ECU hardware failure
- Water in the ECU connector
Checks
- 1Check the ECU plug for water and corrosion
- 2Check supply voltage and earth
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 846T50 switch error
The T50 switch input read by the engine ECU is faulty. The ECU may not know the starter or run position correctly.· OtherOtherCheck soonCauses
- Switch wiring damaged
- Switch failed
Checks
- 1Check the T50 switch and its wiring
- 2Compare the input state with the display
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 847Variant coding error
The engine ECU does not hold the right variant coding for this unit. Engine functions may be limited.· OtherOtherCheck soonCauses
- ECU replaced without coding
- Software mismatch
Checks
- 1Have the variant coding re-entered with the service tool
- 2Check the ECU part number against the unit
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 899Unknown ECU fault
The engine ECU sent a fault code that is not in the controller table. Use a service tool to read what the ECU stored.· OtherOtherCheck soonCauses
- Fault code from a newer ECU
- Software mismatch
Checks
- 1Read the stored ECU codes with the service tool
- 2Check the software versions
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Check the enable and run signal wires and plugs between controller and ECU
- 2Swap the relay with a known good one of the same type
- 3Check the supply voltage and earths at the ECU
- 4Check the wiring and the fuse for the circuit
- 5Read the stored codes with the service tool
- 6Measure the relay coil resistance and the supply at the socket
- 7Have the ECU recoded or replaced by a Thermo King dealer
Causes
- ECU internal failure
- Relay failed
- Enable or run signal wiring fault
- Wiring fault
When to stop
You'll notice: The engine may not start or may stop, with the alarm on the display.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
