EF Logo

Thermo King · Electric standby (SR-2/SR-3/SR-4)

Thermo King Electric standby motor, changeover and generator fault codes

This page covers electric standby operation: the standby motor and its power supply, diesel and electric changeover, and generator faults. On electric standby the compressor is driven by an electric motor from mains power.

More about these parts

Units with electric standby change automatically between diesel and electric power. On units with an on-board generator the controller checks the ground fault, the output current and frequency, and the voltage to frequency ratio.

FaultStop36Thermo King · Electric standby motor, changeover and generator
Code shows hereFAULT36

Where this code shows

Press the alarm key or open the Alarms menu on the controller display to list active alarms.

What do these codes mean?

Thermo King codes OL to 547 are all about the electric standby motor, changeover and generator. The most common failure type is real condition (4 of 18); 7 need an immediate stop. Start with this check: check each supply phase with a meter at the plug.

How urgent are they?

7 of 18 codes here mean stop now; 9 can wait until the shift ends, but find the cause before the next one; 2 are information only.

  • Stop now7
  • Check soon9
  • Info2

What should I check first?

Check each supply phase with a meter at the plug

Shared checks

18 of 18

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Thermo King OLElectric standby overload

    The electric standby motor draws too much current.· Real condition
    Stop now

    Causes

    • Compressor or fan binding
    • Low supply voltage

    Checks

    1. 1Check the supply voltage
    2. 2Check the motor current against the rating
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King tEPElectric standby motor thermal protection alarm

    The thermal protection of the electric standby motor has tripped.· Other
    Stop now

    Causes

    • Motor overloaded or blocked
    • Cooling blocked

    Checks

    1. 1Let the motor cool and check the load
    2. 2Check the motor cooling
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King tP4Power supply thermal protection alarm

    The thermal protection of the power supply has tripped.· Other
    Stop now

    Causes

    • Overloaded supply
    • Poor cooling

    Checks

    1. 1Check the supply load and cooling
    2. 2Let it cool and restart
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 36Electric motor failed to run

    In electric standby the controller asked the electric motor to run but it did not start or stopped.· Other
    Stop now

    Causes

    • Standby power cord or supply not live
    • Motor contactor not closing
    • Motor overload tripped
    • Phase loss at the supply

    Checks

    1. 1Confirm the supply voltage at the plug and breaker
    2. 2Check the contactor closes when run is commanded
    3. 3Check the overload relay for a trip and reset it
    4. 4Measure all three phases at the motor terminals
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 38Electric phase reversed

    The controller detected the supply phase rotation is wrong for the standby motor, so the motor would run backwards.· Other
    Stop now

    Causes

    • Supply wiring at the power plug or panel swapped
    • Extension cord or adapter wired with wrong sequence
    • Phase sensor failure

    Checks

    1. 1Swap any two of the supply phases at the plug to correct rotation
    2. 2Use a phase rotation meter to confirm the sequence at the supply
    3. 3Check any adapters or cords used for wiring errors
    4. 4Retest the standby start after the swap and confirm the motor turns the right way
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 62Ammeter out of calibration

    The current measurement for the electric standby motor is out of calibration.· Part or controller
    Stop now

    Causes

    • Ammeter reading drifted
    • Wiring fault

    Checks

    1. 1Check the ammeter calibration with a clamp meter
    2. 2Recalibrate or replace the ammeter circuit
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Thermo King 90Electric overload

    The electric standby motor drew too much current and the overload tripped or the controller detected overload, shutting the motor down to protect it.· Real condition
    Stop now

    Causes

    • Low supply voltage causing high current
    • Blocked condenser or compressor seizure
    • Motor winding fault
    • Phase imbalance

    Checks

    1. 1Measure the supply voltage at the unit while it runs under full load in electric mode
    2. 2Clean the condenser to reduce the compressor load that drives the current up
    3. 3Measure the current at each phase at the motor
    4. 4Check the overload relay setting against the motor plate and reset it
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 91Check electric ready input

    The electric ready input, a signal that confirms standby power is present and ready, is not behaving as expected when the unit is plugged in.· Other
    Check soon

    Causes

    • Standby supply not live or breaker off
    • Electric ready relay or contactor not closing
    • Wire to the input open or shorted
    • Plug or receptacle damaged

    Checks

    1. 1Confirm the standby supply is live at the power plug and the breaker is on
    2. 2Check the electric ready relay pulls in when the plug is live
    3. 3Test the wire from the relay to the controller input
    4. 4Inspect the plug and receptacle pins for burn marks
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 117Auto switch from diesel to electric

    The unit automatically changed from diesel running to electric standby because it saw standby power connected and the auto switch option is on.· Other
    Info

    Causes

    • Standby power plugged in with auto switch enabled
    • Normal changeover from diesel
    • Electric ready input became active

    Checks

    1. 1Confirm the standby power supply is correct in voltage and phase at the plug
    2. 2Check the auto switch setting in the configuration menu to see if it is enabled
    3. 3Check the unit runs normally on electric power once the switch has happened
    4. 4Clear the alarm and confirm it only repeats when you plug in
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 118Auto switch from electric to diesel

    The unit automatically switched from electric standby to diesel, usually because standby power was lost or unplugged.· Other
    Info

    Causes

    • Standby power lost or unplugged
    • Breaker tripped
    • Auto switch enabled

    Checks

    1. 1Check the standby supply and the breaker for a trip that cut power
    2. 2Check the plug and the power cord for damage or a loose connection
    3. 3Check the electric ready input signal is present when the plug is live
    4. 4Clear the alarm and confirm the unit stays on electric after a restart
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 122Diesel/electric circuit check

    The circuit that selects between diesel and electric operation is faulty.· Other
    Check soon

    Causes

    • Contactor or relay failed
    • Wiring damaged

    Checks

    1. 1Check the changeover relay and wiring
    2. 2Watch the changeover signal on the display
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 141Auto switch diesel to electric disabled

    The unit cannot automatically switch from diesel to electric power.· Other
    Check soon

    Causes

    • Electric ready input fault
    • Changeover circuit fault

    Checks

    1. 1Check the electric ready input and wiring
    2. 2Check the changeover relay
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 148Auto switch electric to diesel disabled

    The unit cannot automatically switch from electric to diesel power.· Other
    Check soon

    Causes

    • Diesel start circuit fault
    • Changeover circuit fault

    Checks

    1. 1Check the diesel start circuit
    2. 2Check the changeover relay
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 518Generator ground fault

    The generator has a ground fault, a leak of current to the frame.· Other
    Check soon

    Causes

    • Generator winding or cable shorted to the frame
    • Moisture in the generator

    Checks

    1. 1Check the generator wiring and insulation
    2. 2Measure the insulation resistance
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 524Generator operational limit: voltage to frequency ratio

    The ratio of the generator output voltage to its frequency is outside its limit, so the output is not within spec.· Other
    Check soon

    Causes

    • Generator regulator fault
    • Engine speed wrong

    Checks

    1. 1Check the engine speed and the generator output
    2. 2Check the regulator
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 525Generator frequency range fault

    The generator output frequency is out of its range.· Lost message
    Check soon

    Causes

    • Engine speed wrong
    • Generator or regulator fault

    Checks

    1. 1Check the engine speed and the generator output frequency
    2. 2Check the regulator
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 526Generator operational limit: output current

    The output current of the generator is beyond its limit.· Real condition
    Check soon

    Causes

    • Overloaded circuit
    • Short in a load

    Checks

    1. 1Check the electric loads and the wiring
    2. 2Measure the output current
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 547AC bus phase loss

    One phase of the AC supply is missing.· Real condition
    Check soon

    Causes

    • Phase lost in the supply cable or plug
    • Blown phase fuse

    Checks

    1. 1Check each phase of the supply with a meter
    2. 2Check the plug and cable
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Check each supply phase with a meter at the plug
  2. 2Check the electric ready input on the display
  3. 3Check the generator wiring and insulation for damage
  4. 4Check the phase order if the motor runs backwards
  5. 5Check the changeover contactor and its wiring
  6. 6Check the electric loads and their connections
  7. 7Check the motor current against the nameplate

Causes

  • Supply phase missing or reversed
  • Electric ready input fault
  • Winding or cable shorted to the frame
  • Motor overloaded

Most common here: real condition (4 of 18)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The unit does not run on electric power, with an alarm on the display.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.