John Deere · Main controller (MCZ) - communication
John Deere Fault Code MCZ 11006.02
Engine controller communication error
What does John Deere code MCZ 11006.02 mean?
The MCZ is not getting messages from the engine controller. Engine speed control from the dial may not work and the engine may stall or sit at one speed. Urgency: stop now - shut down and fix before working on. Check first: check the engine controller supply and ground at its connector with the key on.
- MCZ
- Which controller reports it
- 11006
- What is at fault
- .02
- How it failed
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check the engine controller supply and ground at its connector with the key on
Then 5 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 6 done
Causes
- Open CAN wire between the MCZ and the engine controller
- Engine controller without power or ground
- Damaged engine controller connector
- CAN termination fault on the engine side of the bus
1 more causeFewer causes
- Engine controller fuse blown or its ground strap loose on the engine
How it failed
You'll notice: The MCZ is no longer receiving messages from the engine controller.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: CAN communication between main controller, engine controller and monitor
17 other codes on this part are also lost message (MCZ 11004.02, MCZ 11005.02, MCZ 11007.02, MCZ 11008.02 and more). When they show together, start at the wiring and connector they share.
- MCZ 11004.02MCZ CAN communication errorLost messageCheck soon
- MCZ 11005.02CAN communication error 2Lost messageCheck soon
- MCZ 11006.02Engine controller communication errorLost messageStop now
- MCZ 11007.02(CAN 0) data converter communication error 1Lost messageCheck soon
- MCZ 11008.02(CAN 1) data converter communication error 2Lost messageCheck soon
- MCZ 11009.02(CAN 0) monitor controller communication error 1Lost messageCheck soon
- MCZ 11010.02(CAN 1) monitor controller communication error 2Lost messageCheck soon
- MCZ 11910.02Actual engine speed message errorLost messageCheck soon
- MCZ 11911.02Security signal received from monitorLost messageCheck soon
Show the other 11 codesHide the other codes
- MCZ 11914.02Radiator coolant temperature message errorLost messageCheck soon
- MCZ 11918.02Work mode received message errorLost messageCheck soon
- MCZ 11920.02Fuel flow rate message errorLost messageCheck soon
- MCZ 11983.02Intake air temperature receive errorOtherCheck soon
- MCZ 11984.02Boost temperature receive errorOtherCheck soon
- DSZ 13002.02Monitor: engine controller communication errorLost messageCheck soon
- DSZ 13003.02Monitor: main controller communication error 1Lost messageCheck soon
- DSZ 13004.02Main controller (MCZ) communication error 2Lost messageCheck soon
- DSZ 13005.02Monitor controller (DSZ) communication error 1Lost messageCheck soon
- DSZ 13006.02Monitor controller (DSZ) communication error 2Lost messageCheck soon
- DSZ 13007.02Monitor: machine controller (BCZ) communication errorLost messageCheck soon
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists MCZ 11006.02 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
