EF Logo

John Deere · Engine control unit (ECU) - Communication

John Deere ECU CAN messages, security and communication terminal fault codes

These codes cover the engine controller side of CAN communication and the remote link. The ECU reports messages it did not receive or that were invalid, a security violation, and vehicle identification data.

More about these parts

The communication terminal (JDLink/ZXLink) has its own codes for lost CAN data, a security error and a SIM card problem. The ECF reports an abnormal CAN link.

FaultCheckECU 000237.02John Deere · ECU CAN messages, security and communication terminal
Code shows hereFAULTECU 000237.02

Where this code shows

Turn the key on and open the monitor's diagnostic/fault screen.

What do these codes mean?

John Deere codes ECU 000237.02 to ICZ 14023.02 are all about the eCU CAN messages, security and communication terminal. The most common failure type is lost message (10 of 21); none needs an immediate stop. Start with this check: read the code prefix and note which message, security or terminal function is named.

How urgent are they?

None of the 21 codes here means stop now; all 21 can wait until the shift ends, but find the cause before the next one.

  • Check soon21

What should I check first?

Read the code prefix and note which message, security or terminal function is named

Shared checks

21 of 21

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • John Deere ECU 000237.02No valid VIN security information

    The controller sees an erratic, invalid or out-of-step signal from the vehicle identification data, so it cannot rely on that input.· Erratic or implausible
    Check soon

    Causes

    • Intermittent connection at the vehicle identification data plug or in its harness
    • Chafed wire that touches ground only when the machine moves
    • The vehicle identification data wearing out or failing intermittently

    Checks

    1. 1Wiggle the vehicle identification data harness and plug with the key on while watching the live value for jumps or dropouts
    2. 2Compare the live reading with the machine state (stopped, idling, working) to see when it goes wrong
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • John Deere ECU 000237.31Vehicle number (VN) information

    The controller has set a condition code for the vehicle identification data: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part.· Other
    Check soon

    Causes

    • The real condition behind the vehicle identification data is present
    • A related component or circuit that causes the condition
    • The message or reminder was not reset after the earlier service

    Checks

    1. 1Confirm on the machine that the condition behind the vehicle identification data is real and act on it
    2. 2Read all other codes active at the same time, since this one is often a consequence of another fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000898.09Engine speed request not received

    The ECU is not receiving the engine speed request message from the machine controller within the expected time.· Other
    Check soon

    Causes

    • CAN wiring fault between the MCZ and the engine ECU
    • MCZ not sending the request because of a supply or internal fault
    • ECU connector fault

    Checks

    1. 1Check the CAN wiring between the MCZ and the engine ECU for continuity and shorts
    2. 2Check the MCZ power and ground supply at its connector with the key on
    3. 3Look for MCZ 11006 on the monitor to confirm the link is down
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 001568.02Torque curve selection

    The torque curve selection received by the ECU is invalid, so the ECU cannot pick the right engine torque curve.· Other
    Check soon

    Causes

    • Wiring or connector fault in the circuit behind this code
    • The part or unit the code names failing
    • Low or unstable supply voltage to the controller

    Checks

    1. 1Check the connector and wiring behind this code for corrosion, oil and pins that are pushed out
    2. 2Measure supply voltage and ground at the controller and clear the code to see if it returns
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 001638.09Hydraulic oil temperature message not received or timed out

    The controller does not receive the expected CAN messages received by the ECU, or it arrives too slowly or with invalid data, so that data cannot be used.· Lost message
    Check soon

    Causes

    • The unit that should send the CAN messages received by the ECU is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the CAN messages received by the ECU before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ECU 002000.13Security violation

    The ECU security check failed its security check, so the security data exchanged between controllers did not match.· Other
    Check soon

    Causes

    • A controller fitted from another machine or not programmed for this one
    • Mismatched or old controller software
    • Damaged or interrupted security data on the bus

    Checks

    1. 1Confirm every controller on the machine is the right part number and software for it
    2. 2Re-program or re-link the controllers with the service tool as the manual describes
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 002003.09CAN timeout or invalid data

    The controller does not receive the expected CAN messages received by the ECU, or it arrives too slowly or with invalid data, so that data cannot be used.· Lost message
    Check soon

    Causes

    • The unit that should send the CAN messages received by the ECU is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the CAN messages received by the ECU before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ECU 002003.13Security violation

    The ECU security check failed its security check, so the security data exchanged between controllers did not match.· Other
    Check soon

    Causes

    • A controller fitted from another machine or not programmed for this one
    • Mismatched or old controller software
    • Damaged or interrupted security data on the bus

    Checks

    1. 1Confirm every controller on the machine is the right part number and software for it
    2. 2Re-program or re-link the controllers with the service tool as the manual describes
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 002005.09Abnormal update rate

    The controller does not receive the expected CAN messages received by the ECU, or it arrives too slowly or with invalid data, so that data cannot be used.· Lost message
    Check soon

    Causes

    • The unit that should send the CAN messages received by the ECU is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the CAN messages received by the ECU before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ECU 002017.09CAN timeout or invalid data

    The controller does not receive the expected CAN messages received by the ECU, or it arrives too slowly or with invalid data, so that data cannot be used.· Lost message
    Check soon

    Causes

    • The unit that should send the CAN messages received by the ECU is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the CAN messages received by the ECU before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ECU 002017.13Security violation

    The ECU security check failed its security check, so the security data exchanged between controllers did not match.· Other
    Check soon

    Causes

    • A controller fitted from another machine or not programmed for this one
    • Mismatched or old controller software
    • Damaged or interrupted security data on the bus

    Checks

    1. 1Confirm every controller on the machine is the right part number and software for it
    2. 2Re-program or re-link the controllers with the service tool as the manual describes
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 002146.09HCI pump message missing

    The controller does not receive the expected CAN messages received by the ECU, or it arrives too slowly or with invalid data, so that data cannot be used.· Lost message
    Check soon

    Causes

    • The unit that should send the CAN messages received by the ECU is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the CAN messages received by the ECU before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ECF 11604.02Abnormal CAN communication

    The engine controller (ECF) reports abnormal CAN communication.· Lost message
    Check soon

    Causes

    • CAN wire between the ECF and the main controller broken or shorted
    • Corroded or loose connector on the ECF or on the CAN circuit
    • Main controller off or faulted so it is not talking
    • Missing or faulty CAN termination

    Checks

    1. 1Check the ECF and main controller fuses, power and ground first
    2. 2Inspect the CAN connectors at both controllers for corrosion, bent pins and water
    3. 3Measure the CAN wire continuity and termination as the wiring manual describes, with the power off
    4. 4Read the main controller communication codes to see whether they appear at the same time
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere DSZ 14006.02Communication terminal: communication error

    The controller does not receive the expected communication terminal (JDLink/ZXLink), or it arrives too slowly or with invalid data, so that data cannot be used.· Lost message
    Check soon

    Causes

    • The unit that should send the communication terminal (JDLink/ZXLink) is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the communication terminal (JDLink/ZXLink) before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ICZ 14006.02Communication terminal: communication error

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Lost message
    Check soon

    Causes

    • The unit that should send the communication terminal (JDLink/ZXLink) is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the communication terminal (JDLink/ZXLink) before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere DSZ 14021.02Communication terminal security error

    The monitor reports a security malfunction in the mobile communication terminal: the terminal and the machine did not agree on their security data, so the link is blocked.· Real condition
    Check soon

    Causes

    • Terminal swapped or reprogrammed, so its security key does not match the machine
    • Security data lost after a battery disconnect or a controller change
    • Terminal firmware fault

    Checks

    1. 1Ask whether the terminal, monitor or MCZ was replaced recently
    2. 2Check that the terminal has power, ground and its antenna connected
    3. 3Have the dealer re-register the terminal to the machine with the service tool
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • John Deere ICZ 14021.02Communication terminal security error

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Real condition
    Check soon

    Causes

    • Terminal swapped or reprogrammed, so its security key does not match the machine
    • Security data lost after a battery disconnect or a controller change
    • Terminal firmware fault

    Checks

    1. 1Ask whether the terminal, monitor or MCZ was replaced recently
    2. 2Check that the terminal has power, ground and its antenna connected
    3. 3Have the dealer re-register the terminal to the machine with the service tool
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • John Deere DSZ 14022.02SIM card error

    The communication terminal cannot use its SIM card, so mobile data and remote monitoring are unavailable.· Other
    Check soon

    Causes

    • SIM card missing, loose, or its contacts dirty
    • SIM subscription expired or deactivated
    • SIM slot in the terminal damaged

    Checks

    1. 1Check that the SIM is seated in the terminal and its contacts are clean
    2. 2Confirm with the telematics provider that the SIM subscription is active
    3. 3Check the terminal antenna cable and signal strength
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ICZ 14022.02SIM card error

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Other
    Check soon

    Causes

    • SIM card missing, loose, or its contacts dirty
    • SIM subscription expired or deactivated
    • SIM slot in the terminal damaged

    Checks

    1. 1Check that the SIM is seated in the terminal and its contacts are clean
    2. 2Confirm with the telematics provider that the SIM subscription is active
    3. 3Check the terminal antenna cable and signal strength
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere DSZ 14023.02Security error

    The communication terminal reports a communication error with the main controller (MCZ), flagged as a security error.· Lost message
    Check soon

    Causes

    • CAN link between the terminal and the MCZ interrupted
    • MCZ replaced or reprogrammed, so security data no longer matches
    • Terminal firmware mismatch

    Checks

    1. 1Check the CAN wiring and connectors between the terminal and the MCZ
    2. 2Check whether MCZ communication codes are active at the same time
    3. 3Have the dealer pair the terminal and the MCZ again
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ICZ 14023.02Security error

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Lost message
    Check soon

    Causes

    • CAN link between the terminal and the MCZ interrupted
    • MCZ replaced or reprogrammed, so security data no longer matches
    • Terminal firmware mismatch

    Checks

    1. 1Check the CAN wiring and connectors between the terminal and the MCZ
    2. 2Check whether MCZ communication codes are active at the same time
    3. 3Have the dealer pair the terminal and the MCZ again
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Read the code prefix and note which message, security or terminal function is named
  2. 2Check the sender controller for power, ground and its fuse before the CAN wiring
  3. 3After a controller swap ask the dealer to re-register the controller and security data with the service tool
  4. 4For terminal codes check the SIM is seated, the subscription is active and the antenna cable is connected
  5. 5Inspect CAN connectors for corrosion and measure the CAN wire resistance with the battery off

Causes

  • CAN wire or connector fault between the ECU and the other controllers
  • Security or identification data not matching after a controller was replaced or reprogrammed
  • Communication terminal off, without antenna, SIM or subscription
  • Another controller not sending its message

Most common here: lost message (10 of 21)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: Engine information may be missing or default, the machine may not start after a controller swap, and remote monitoring may stop; digging is not affected by the terminal codes.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.