EF Logo

John Deere · Main controller (MCZ) - internal

John Deere Controller self-tests and memory faults (MCZ, ECF, monitor) fault codes

The main controller (MCZ), the engine controller (ECF) and the monitor each test their own memory when they start. The codes name the test that failed: EEPROM (saved settings), RAM (working memory), flash (the program), the analogue to digital converter or the sensor supply.

More about these parts

These are mostly internal faults, but low voltage or an interrupted update can set them.

FaultStopMCZ 11000.02John Deere · Controller self-tests and memory faults (MCZ, ECF, monitor)
Code shows hereFAULTMCZ 11000.02

Where this code shows

Turn the key on and open the monitor's diagnostic/fault screen.

What do these codes mean?

John Deere codes MCZ 11000.02 to ICZ 14008.02 are all about the controller self-tests and memory faults (MCZ, ECF, monitor). Most are part or controller faults; 16 need an immediate stop. Start with this check: check battery voltage and the controller ground connections first.

How urgent are they?

16 of 18 codes here mean stop now; the other 2 can wait until the shift ends, but find the cause before the next one.

  • Stop now16
  • Check soon2

What should I check first?

Check battery voltage and the controller ground connections first

Shared checks

18 of 18

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • John Deere MCZ 11000.02Main controller EEPROM fault

    The MCZ failed its memory (EEPROM) self-check.· Part or controller
    Stop now

    Causes

    • Corrupted calibration or configuration data in the MCZ memory after a power dip during a write
    • Failing internal memory in the MCZ itself
    • Very low or unstable supply voltage during start-up that interrupted a data write

    Checks

    1. 1Cycle the key off for a minute, restart and see whether the code returns; a one-off after a flat battery is not always a failed controller
    2. 2Measure battery voltage at the MCZ power pins while cranking and with the engine running
    3. 3Check the MCZ ground and power connectors for corrosion and heat marks
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere MCZ 11001.02Main controller RAM fault

    The MCZ working memory failed its self-check.· Part or controller
    Stop now

    Causes

    • Failing working memory (RAM) inside the MCZ
    • Brief supply voltage drops causing the controller to reset mid-process
    • Water damage or corrosion inside the MCZ housing

    Checks

    1. 1Check battery voltage and the main power and ground pins at the MCZ connector for a clean supply
    2. 2Inspect the MCZ housing and connector seals for water ingress and corrosion
    3. 3Clear the code and run the machine; if it returns at once the controller is likely faulty
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere MCZ 11002.02Abnormal A/D converter

    The main controller's analogue to digital converter, which turns sensor voltages into numbers, failed its self test, so all sensor readings are unreliable.· Other
    Stop now

    Causes

    • Low or unstable supply voltage when the controller started
    • A failing controller or damaged memory
    • Interrupted software update or power loss during a write

    Checks

    1. 1Check battery voltage and ground, then clear the code and see whether it returns after a restart
    2. 2If the code returns at once with good supply, the controller itself is the likely fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere MCZ 11003.03Main controller sensor supply voltage fault

    The MCZ saw its 5 V sensor supply out of range high.· Lost message
    Check soon

    Causes

    • A sensor harness shorted to a higher voltage wire, pulling the 5 V line up
    • Internal fault in the MCZ 5 V regulator
    • Corroded or water-filled MCZ connector letting a higher voltage leak into the 5 V circuit

    Checks

    1. 1Measure the 5 V supply at several sensor plugs with the key on; all reading high points to the MCZ itself
    2. 2Unplug the sensors one at a time and see whether the voltage returns to normal
    3. 3Inspect the harness for damage where it touches a battery or 24 V wire
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ECF 11600.02Abnormal EEPROM

    The engine controller (ECF) found an error in its EEPROM memory, which stores calibration and settings; the stored data cannot be trusted.· Part or controller
    Stop now

    Causes

    • Low or unstable supply voltage when the controller started
    • A failing controller or damaged memory
    • Interrupted software update or power loss during a write

    Checks

    1. 1Check battery voltage and ground, then clear the code and see whether it returns after a restart
    2. 2If the code returns at once with good supply, the controller itself is the likely fault
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere ECF 11601.02Abnormal RAM

    The engine controller (ECF) found an error in its working memory (RAM) during self test, so it cannot run reliably.· Part or controller
    Stop now

    Causes

    • Low or unstable supply voltage when the controller started
    • A failing controller or damaged memory
    • Interrupted software update or power loss during a write

    Checks

    1. 1Check battery voltage and ground, then clear the code and see whether it returns after a restart
    2. 2If the code returns at once with good supply, the controller itself is the likely fault
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere ECF 11602.02Abnormal A/D conversion

    The ECF analogue to digital converter, which turns sensor voltages into numbers, failed its self check, so sensor readings are unreliable.· Other
    Stop now

    Causes

    • Low or unstable supply voltage when the controller started
    • A failing controller or damaged memory
    • Interrupted software update or power loss during a write

    Checks

    1. 1Check battery voltage and ground, then clear the code and see whether it returns after a restart
    2. 2If the code returns at once with good supply, the controller itself is the likely fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECF 11603.03Abnormal sensor voltage

    The ECF found its sensor supply voltage outside the permitted range, which makes all the sensors it reads unreliable.· Other
    Check soon

    Causes

    • Signal wire of the engine controller (ECF) shorted to the 5 V supply or to battery voltage
    • Open return (ground) wire at the engine controller (ECF), which lets the signal float high
    • The engine controller (ECF) failed internally with a stuck high output

    Checks

    1. 1Unplug the engine controller (ECF) and, key on, measure the harness signal pin: a value near 5 V points to a harness short or a controller fault rather than the part
    2. 2Check continuity of the engine controller (ECF) return wire to the controller sensor ground with both ends disconnected
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere DSZ 13000.02Flash memory error 1

    The monitor failed the first check of its flash memory at start-up, so the program image or its checksum could not be read reliably.· Part or controller
    Stop now

    Causes

    • Program in flash damaged or checksum wrong after an interrupted update
    • Supply voltage dipped while the monitor was starting, corrupting the first read
    • Flash memory chip failing

    Checks

    1. 1Ask whether the monitor software was updated recently and whether the update finished
    2. 2Check battery voltage during cranking; a dip below the manual limit can corrupt the start-up read
    3. 3Cycle the key; if the code returns on every start, plan a software reload or a replacement monitor
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere DSZ 13001.02Flash memory error 2

    The monitor failed the second flash check, which covers the data area, so saved data or logs could not be read reliably.· Part or controller
    Stop now

    Causes

    • Saved data block in flash unreadable after power loss during a write
    • Flash chip wearing out
    • Software mismatch after a monitor swap

    Checks

    1. 1Note which settings or logs have been lost; that shows whether the data area is damaged
    2. 2Reload the monitor software and settings with the service tool and see whether the code clears
    3. 3Check the supply voltage on the monitor connector with the key on
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere DSZ 14001.02Flash memory read/write error

    The monitor failed to read or write its flash memory, so settings and logs may not be saved or loaded.· Part or controller
    Stop now

    Causes

    • Key turned off while the monitor was saving settings
    • Flash writes failing on worn memory
    • Low voltage while saving

    Checks

    1. 1Change a setting, switch the key off and on, and check whether the change was kept; if not, writes are failing
    2. 2Check battery condition and that the key-off does not cut power mid-save, for example a loose battery cable
    3. 3Replace the monitor only if a software reload does not stop the error
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere ICZ 14001.02Flash memory read/write error

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Part or controller
    Stop now

    Causes

    • Key turned off while the monitor was saving settings
    • Flash writes failing on worn memory
    • Low voltage while saving

    Checks

    1. 1Change a setting, switch the key off and on, and check whether the change was kept; if not, writes are failing
    2. 2Check battery condition and that the key-off does not cut power mid-save, for example a loose battery cable
    3. 3Replace the monitor only if a software reload does not stop the error
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere DSZ 14002.02External RAM read/write error

    The monitor failed a read or write test on its external RAM, which it uses for the display and data handling.· Other
    Stop now

    Causes

    • Memory chip or solder joint failing from vibration or heat
    • Moisture or bent pins in the monitor connector
    • Low supply voltage during self test

    Checks

    1. 1Look for display glitches, frozen screens or garbled text that go with this code
    2. 2Check the monitor connector for water and bent pins, and the supply voltage
    3. 3Replace the monitor if the code is permanent and supply and plug are good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ICZ 14002.02External RAM read/write error

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Other
    Stop now

    Causes

    • Memory chip or solder joint failing from vibration or heat
    • Moisture or bent pins in the monitor connector
    • Low supply voltage during self test

    Checks

    1. 1Look for display glitches, frozen screens or garbled text that go with this code
    2. 2Check the monitor connector for water and bent pins, and the supply voltage
    3. 3Replace the monitor if the code is permanent and supply and plug are good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere DSZ 14003.02Abnormal EEPROM

    The monitor found a fault in its EEPROM, the small memory that holds saved settings.· Part or controller
    Stop now

    Causes

    • Saved-settings area failed or corrupted
    • Power lost during a settings save
    • EEPROM chip worn

    Checks

    1. 1Check whether language, units or work mode reset themselves after every key-off
    2. 2Re-enter the settings and test whether they survive a key cycle
    3. 3Replace the monitor if settings cannot be saved at all
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere ICZ 14003.02Abnormal EEPROM

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Part or controller
    Stop now

    Causes

    • Saved-settings area failed or corrupted
    • Power lost during a settings save
    • EEPROM chip worn

    Checks

    1. 1Check whether language, units or work mode reset themselves after every key-off
    2. 2Re-enter the settings and test whether they survive a key cycle
    3. 3Replace the monitor if settings cannot be saved at all
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere DSZ 14008.02Abnormal internal RAM

    The monitor found a fault in its internal RAM during self test, which is the processor own working memory.· Part or controller
    Stop now

    Causes

    • Processor internal memory fault
    • Heat or vibration damage on the monitor board
    • Low voltage at start

    Checks

    1. 1Check whether the monitor reboots or freezes by itself, which goes with an internal RAM fault
    2. 2Check supply and ground at the monitor plug
    3. 3Replace the monitor if the fault returns at once with good supply
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • John Deere ICZ 14008.02Abnormal internal RAM

    The information controller (ICZ) list carries the same code as the monitor (DSZ) list.· Part or controller
    Stop now

    Causes

    • Processor internal memory fault
    • Heat or vibration damage on the monitor board
    • Low voltage at start

    Checks

    1. 1Check whether the monitor reboots or freezes by itself, which goes with an internal RAM fault
    2. 2Check supply and ground at the monitor plug
    3. 3Replace the monitor if the fault returns at once with good supply
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

Shared checks

Checks, in order

  1. 1Check battery voltage and the controller ground connections first
  2. 2Clear the code, switch off, wait, restart, and see whether it returns at once
  3. 3For sensor supply codes unplug sensors one by one and watch whether the code clears, which finds a shorted sensor
  4. 4Check whether saved settings survive a key off and on; if not, the saved-settings memory is failing
  5. 5If the code returns at once with good supply and wiring, the controller itself is the likely fault

Causes

  • Low or unstable battery voltage or a poor ground at start-up
  • Power lost while the controller was saving settings or updating its software
  • A short on the 5 V sensor supply pulling the voltage down
  • Failed memory or controller internally

Most codes here: part or controller (12 of 18)

Check power and ground at the module connector with the key on, then its fuses.

When to stop

You'll notice: The machine may refuse to start work functions, the monitor may show garbage, restart or lose its settings, and a stored code may return after clearing.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.