EF Logo

John Deere · Climate controller (ACF) - sensors and controls

John Deere Climate controller (ACF) sensors, servomotors and communication fault codes

The air conditioner controller (ACF) reads an air recirculation sensor, an ambient air temperature sensor, a solar radiation sensor and an evaporator freeze switch, and flags each when the circuit is open or shorted. Servomotor codes cover the air flap and blower port motors, and a communication code covers the link to the rest of the machine.

FaultCheckACF 11John Deere · Climate controller (ACF) sensors, servomotors and communication
Code shows hereFAULTACF 11

Where this code shows

Turn the key on and open the monitor's diagnostic/fault screen.

What do these codes mean?

John Deere codes ACF 11 to ACF 92 are all about the climate controller (ACF) sensors, servomotors and communication. The most common failure type is short circuit (3 of 11); none needs an immediate stop. Start with this check: check which circuit the code names and unplug that sensor or switch.

How urgent are they?

None of the 11 codes here means stop now; all 11 can wait until the shift ends, but find the cause before the next one.

  • Check soon11

What should I check first?

Check which circuit the code names and unplug that sensor or switch

Shared checks

11 of 11

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • John Deere ACF 11Open circuit in air recirculation sensor

    The climate controller finds the air recirculation sensor circuit open, so it cannot tell whether cab air is being recirculated.· Open circuit
    Check soon

    Causes

    • Sensor plug unplugged or a pin pushed out at the recirculation actuator
    • Wire broken in the cab harness behind the dash
    • Failed sensor element

    Checks

    1. 1Check the recirculation sensor plug behind the dash or at the air box
    2. 2Measure sensor resistance and wire continuity; an infinite reading is an open
    3. 3Switch recirculation on and off and watch whether the air flap moves
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • John Deere ACF 12Short-circuited air recirculation sensor

    The climate controller finds the air recirculation sensor circuit shorted, so its signal is stuck at one level.· Short circuit
    Check soon

    Causes

    • Wire chafed to ground behind the dash
    • Sensor element shorted
    • Water in the sensor plug

    Checks

    1. 1Unplug the sensor and see whether the code changes to open; if so the short is in the sensor
    2. 2Measure sensor resistance against the manual; near zero is a short
    3. 3Look for a pinched wire at the air box
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

  • John Deere ACF 13Open circuit in ambient air temperature sensor

    The climate controller finds the ambient (outside) air temperature sensor circuit open, so outside temperature is unknown and automatic control may misjudge the load.· Open circuit
    Check soon

    Causes

    • Plug unplugged at the sensor outside the cab
    • Wire broken near the sensor from washing or vibration
    • Failed sensor

    Checks

    1. 1Look at the ambient sensor plug on the outside of the cab and the wire leading to it
    2. 2Measure sensor resistance and compare it with the manual table for the air temperature
    3. 3Check whether the display shows an outside temperature
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • John Deere ACF 14Short-circuited ambient air temperature sensor

    The climate controller finds the ambient air temperature sensor circuit shorted, so it reads a false very hot or very cold outside temperature.· Short circuit
    Check soon

    Causes

    • Wire chafed to ground near the sensor
    • Water in the sensor plug
    • Sensor element shorted

    Checks

    1. 1Unplug the ambient sensor and see whether the code changes to open
    2. 2Measure the sensor resistance; near zero is a short
    3. 3Inspect the wire along its run for chafing and the plug for water
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

  • John Deere ACF 18Short-circuited solar radiation sensor

    The climate controller finds the solar radiation sensor circuit shorted, so it cannot judge sun load on the cab.· Short circuit
    Check soon

    Causes

    • Solar sensor element shorted
    • Wire chafed under the dash top
    • Water in the plug

    Checks

    1. 1Unplug the solar sensor and check whether the code changes to open
    2. 2Measure the sensor with a meter in light and in shade; the reading should change
    3. 3Check the cable under the dash top for pinching
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

  • John Deere ACF 21Open circuit in air conditioner freeze control switch

    The climate controller finds the evaporator freeze control switch circuit open, so it cannot tell whether the evaporator is icing.· Open circuit
    Check soon

    Causes

    • Freeze switch plug off at the evaporator
    • Wire broken between the switch and the controller
    • Switch contacts failed open

    Checks

    1. 1Check the freeze switch plug near the air box
    2. 2Check continuity of the switch and its wire
    3. 3If the compressor never engages, an open freeze switch can be the reason
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • John Deere ACF 22Short-circuited air conditioner freeze control switch

    The climate controller finds the evaporator freeze control switch circuit shorted, which can stop the compressor from running.· Lost message
    Check soon

    Causes

    • Switch stuck closed or shorted
    • Wire shorted to ground
    • Water in the plug

    Checks

    1. 1Unplug the switch and see whether the code changes to open
    2. 2Measure the switch with a meter at room temperature and when the evaporator is cold
    3. 3Watch whether the compressor clutch cycles
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ACF 43Abnormal air conditioner and heater blower port change servomotor

    The air conditioner and heater servomotors does not respond as commanded or is stuck, which the controller detects from its feedback.· Other
    Check soon

    Causes

    • The air conditioner and heater servomotors stuck from dirt, wear or damage
    • Actuator or driver weak or failing
    • Supply or wiring fault so the part is not driven properly

    Checks

    1. 1Move or command the air conditioner and heater servomotors while watching the response; no movement points at the part, movement with a code points at the feedback
    2. 2Check the supply voltage and the ground at the air conditioner and heater servomotors plug while it is commanded
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ACF 44Abnormal air conditioner and heater mixer servomotor

    The air conditioner and heater servomotors does not respond as commanded or is stuck, which the controller detects from its feedback.· Other
    Check soon

    Causes

    • The air conditioner and heater servomotors stuck from dirt, wear or damage
    • Actuator or driver weak or failing
    • Supply or wiring fault so the part is not driven properly

    Checks

    1. 1Move or command the air conditioner and heater servomotors while watching the response; no movement points at the part, movement with a code points at the feedback
    2. 2Check the supply voltage and the ground at the air conditioner and heater servomotors plug while it is commanded
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ACF 91Communication error

    The controller does not receive the expected air conditioner controller (ACF) communication, or it arrives too slowly or with invalid data, so that data cannot be used.· Lost message
    Check soon

    Causes

    • The unit that should send the air conditioner controller (ACF) communication is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the air conditioner controller (ACF) communication before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ACF 92CAN bus off error

    The air conditioner controller has taken itself off the CAN bus after too many errors, so it no longer exchanges data with the other controllers.· Lost message
    Check soon

    Causes

    • The unit that should send the air conditioner controller (ACF) communication is off, damaged or missing its power
    • Broken, shorted or corroded CAN wire or connector between the units
    • Missing or faulty CAN termination on the bus

    Checks

    1. 1Check the power, ground and fuse of the unit that sends the air conditioner controller (ACF) communication before the CAN wiring
    2. 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Check which circuit the code names and unplug that sensor or switch
  2. 2Measure sensor resistance and wire continuity: infinite is an open, near zero is a short
  3. 3Operate the climate controls and watch each air flap move to confirm servomotors
  4. 4Check the ACF controller power, ground and fuse before the sensors
  5. 5Look for pinched or chafed wires behind the dash and at the air box

Causes

  • Sensor or switch failed, giving an open or shorted circuit
  • Plug off or wire broken behind the dash or at the air box
  • Servomotor jammed or its linkage broken
  • CAN or power fault on the ACF

Most common here: short circuit (3 of 11)

Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

When to stop

You'll notice: Cab climate control gives wrong temperature or airflow, or stops cooling; this does not stop the machine working.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.