John Deere · Armrest control unit (ACU) - tractor
John Deere Armrest control unit (ACU) tractor controls fault codes
The armrest control unit (ACU) reads the operator controls of the tractor: the single lever control and its hand presence switch, operator-in-seat detection, the hand throttle, the SCV control lever switches and the rear PTO system. It also reports ECU messages it did not receive over CAN, which means the engine controller is not sending.
Where this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
What do these codes mean?
John Deere codes ACU 000158.04 to ACU 523960.31 are all about the armrest control unit (ACU) tractor controls. The most common failure type is lost message (6 of 18); none needs an immediate stop. Start with this check: read which control the code names and check its switch or sensor at the armrest.
How urgent are they?
None of the 18 codes here means stop now; 17 can wait until the shift ends, but find the cause before the next one; 1 is information only.
- Check soon17
- Info1
What should I check first?
Read which control the code names and check its switch or sensor at the armrest
Shared checks18 of 18
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
John Deere ACU 000158.04Rear PTO system: low ACU voltage
The controller reads the rear PTO signal below its normal range, so it cannot use the value and the function that depends on it runs on a fallback or is switched off. The ACU sees low voltage on the rear PTO circuit.· Shorted lowShorted lowCheck soonCauses
- Signal wire of the rear PTO shorted to ground
- Broken or unplugged 5 V supply wire to the rear PTO
- The rear PTO failed internally with a stuck low output
Checks
- 1With the rear PTO unplugged and the key on, check for the 5 V supply on its harness plug; no supply means a broken feed wire or a faulty controller output
- 2Measure the signal wire to ground with both ends disconnected; a very low resistance means a short to ground in the harness
- 3Measure the supply and ground at the ACU and the PTO connector.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
John Deere BCU 000186.17Rear PTO speed not registered
The rear PTO reading is below its normal range, so the controller reports a low value; this can be a real condition on the machine and not only a wiring fault. The rear PTO speed is not registered, so PTO speed control is lost.· Lost messageLost messageCheck soonCauses
- A real low condition on the machine, such as low level, low pressure or a cold engine, behind the rear PTO
- The rear PTO reading low because of a drifting sensor
- Supply or feed problem that holds the value down
Checks
- 1Confirm the real value with an independent gauge or by inspection before blaming the rear PTO
- 2Look for related codes and for a physical cause such as a low level, leak or weak supply
- 3Check the PTO speed sender air gap and wire.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ACU 000974.02Hand throttle circuit voltage erratic
The controller sees an erratic, invalid or out-of-step signal from the hand throttle circuit, so it cannot rely on that input. The hand throttle signal is erratic or high, so engine speed may not follow the lever.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connection at the hand throttle circuit plug or in its harness
- Chafed wire that touches ground only when the machine moves
- The hand throttle circuit wearing out or failing intermittently
Checks
- 1Wiggle the hand throttle circuit harness and plug with the key on while watching the live value for jumps or dropouts
- 2Compare the live reading with the machine state (stopped, idling, working) to see when it goes wrong
- 3Move the hand throttle through its range and watch the value; it should change smoothly.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
John Deere ACU 000974.03Hand throttle circuit voltage high
The controller reads the hand throttle circuit signal above its normal range, so it cannot use the value and the function that depends on it runs on a fallback or is switched off. The hand throttle signal is erratic or high, so engine speed may not follow the lever.· Shorted highShorted highCheck soonCauses
- Signal wire of the hand throttle circuit shorted to the 5 V supply or to battery voltage
- Open return (ground) wire at the hand throttle circuit, which lets the signal float high
- The hand throttle circuit failed internally with a stuck high output
Checks
- 1Unplug the hand throttle circuit and, key on, measure the harness signal pin: a value near 5 V points to a harness short or a controller fault rather than the part
- 2Check continuity of the hand throttle circuit return wire to the controller sensor ground with both ends disconnected
- 3Move the hand throttle through its range and watch the value; it should change smoothly.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
John Deere BCU 000980.07Rear PTO switch fault
The rear PTO does not respond as commanded or is stuck, which the controller detects from its feedback. The rear PTO switch is stuck or not responding.· Part or controllerPart or controllerCheck soonCauses
- The rear PTO stuck from dirt, wear or damage
- Actuator or driver weak or failing
- Supply or wiring fault so the part is not driven properly
Checks
- 1Move or command the rear PTO while watching the response; no movement points at the part, movement with a code points at the feedback
- 2Check the supply voltage and the ground at the rear PTO plug while it is commanded
- 3Test the PTO switch with a meter in both positions.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
John Deere ACU 002000.09Communication system: ECU message missing
The controller does not receive the expected armrest control unit (ACU) CAN messages, or it arrives too slowly or with invalid data, so that data cannot be used. The ACU is not receiving the engine controller message, so engine data is missing.· Lost messageLost messageCheck soonCauses
- The unit that should send the armrest control unit (ACU) CAN messages is off, damaged or missing its power
- Broken, shorted or corroded CAN wire or connector between the units
- Missing or faulty CAN termination on the bus
Checks
- 1Check the power, ground and fuse of the unit that sends the armrest control unit (ACU) CAN messages before the CAN wiring
- 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
- 3Check the ECU is powered and running before the CAN wiring.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ACU 002003.09Communication system: PTP/PTI message missing
The controller does not receive the expected armrest control unit (ACU) CAN messages, or it arrives too slowly or with invalid data, so that data cannot be used. The ACU is not receiving the PTP/PTI message.· Lost messageLost messageCheck soonCauses
- The unit that should send the armrest control unit (ACU) CAN messages is off, damaged or missing its power
- Broken, shorted or corroded CAN wire or connector between the units
- Missing or faulty CAN termination on the bus
Checks
- 1Check the power, ground and fuse of the unit that sends the armrest control unit (ACU) CAN messages before the CAN wiring
- 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
- 3Check the controller that sends PTP/PTI is powered and its CAN plug is seated.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ACU 002020.09Communication system: SFA message missing
The controller does not receive the expected armrest control unit (ACU) CAN messages, or it arrives too slowly or with invalid data, so that data cannot be used. The ACU is not receiving the SFA message.· Lost messageLost messageCheck soonCauses
- The unit that should send the armrest control unit (ACU) CAN messages is off, damaged or missing its power
- Broken, shorted or corroded CAN wire or connector between the units
- Missing or faulty CAN termination on the bus
Checks
- 1Check the power, ground and fuse of the unit that sends the armrest control unit (ACU) CAN messages before the CAN wiring
- 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
- 3Check the sender of the SFA message for power and CAN connection.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ACU 002049.09Communication system: CAB message missing
The controller does not receive the expected armrest control unit (ACU) CAN messages, or it arrives too slowly or with invalid data, so that data cannot be used. The ACU is not receiving the cab message.· Lost messageLost messageCheck soonCauses
- The unit that should send the armrest control unit (ACU) CAN messages is off, damaged or missing its power
- Broken, shorted or corroded CAN wire or connector between the units
- Missing or faulty CAN termination on the bus
Checks
- 1Check the power, ground and fuse of the unit that sends the armrest control unit (ACU) CAN messages before the CAN wiring
- 2Inspect the CAN connectors for corrosion and measure the CAN wire continuity and termination as the wiring manual describes
- 3Check the cab controller power and CAN connector.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere BCU 302071.31Rear PTO switch must be turned off
The controller has set a condition code for the rear PTO: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part. The rear PTO switch must be turned off before engaging.· OtherOtherInfoCauses
- The real condition behind the rear PTO is present
- A related component or circuit that causes the condition
- The message or reminder was not reset after the earlier service
Checks
- 1Confirm on the machine that the condition behind the rear PTO is real and act on it
- 2Read all other codes active at the same time, since this one is often a consequence of another fault
- 3Switch the PTO off, then on again, and watch the state.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere BCU 302073.31Rear PTO solenoid valve circuit trouble
The controller detects a short circuit on the rear PTO, so the circuit draws too much current or the signal is pulled to a fixed level. The rear PTO solenoid valve circuit is shorted, so the PTO cannot engage.· Short circuitShort circuitCheck soonCauses
- Wire to the rear PTO chafed through and touching ground or a supply wire
- Water or oil inside the rear PTO connector bridging pins
- Internal short inside the rear PTO
Checks
- 1Unplug the rear PTO and see whether the code changes from a short to an open; if it does, the part is the likely culprit
- 2Measure each wire to ground with both ends disconnected; a low reading means a harness short
- 3Measure the PTO solenoid coil and check its wire for a short.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
John Deere ACU 523775.02Single lever control: hand presence switch
The controller sees an erratic, invalid or out-of-step signal from the single lever control, so it cannot rely on that input. The single lever hand presence switch signal is erratic, so the lever may not enable.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connection at the single lever control plug or in its harness
- Chafed wire that touches ground only when the machine moves
- The single lever control wearing out or failing intermittently
Checks
- 1Wiggle the single lever control harness and plug with the key on while watching the live value for jumps or dropouts
- 2Compare the live reading with the machine state (stopped, idling, working) to see when it goes wrong
- 3Press and release the hand presence switch and watch its state on the service screen.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
John Deere ACU 523805.03Single lever control fault
The controller reads the single lever control signal above its normal range, so it cannot use the value and the function that depends on it runs on a fallback or is switched off. The single lever signal is above range, so lever functions are cut off.· OtherOtherCheck soonCauses
- Signal wire of the single lever control shorted to the 5 V supply or to battery voltage
- Open return (ground) wire at the single lever control, which lets the signal float high
- The single lever control failed internally with a stuck high output
Checks
- 1Unplug the single lever control and, key on, measure the harness signal pin: a value near 5 V points to a harness short or a controller fault rather than the part
- 2Check continuity of the single lever control return wire to the controller sensor ground with both ends disconnected
- 3Unplug the single lever and check the signal for a short to supply.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere ACU 523923.02Operator controls: SCV i control lever switch erratic
The controller sees an erratic, invalid or out-of-step signal from the selective control valve (SCV) I control lever switch, so it cannot rely on that input. The SCV control lever switch signal is erratic, high or low, so the remote valve may not respond.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connection at the selective control valve (SCV) I control lever switch plug or in its harness
- Chafed wire that touches ground only when the machine moves
- The selective control valve (SCV) I control lever switch wearing out or failing intermittently
Checks
- 1Wiggle the selective control valve (SCV) I control lever switch harness and plug with the key on while watching the live value for jumps or dropouts
- 2Compare the live reading with the machine state (stopped, idling, working) to see when it goes wrong
- 3Operate the SCV lever and watch its switch value change on the service screen.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
John Deere ACU 523923.03Operator controls: SCV i control lever switch high
The controller reads the selective control valve (SCV) I control lever switch signal above its normal range, so it cannot use the value and the function that depends on it runs on a fallback or is switched off. The SCV control lever switch signal is erratic, high or low, so the remote valve may not respond.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Signal wire of the selective control valve (SCV) I control lever switch shorted to the 5 V supply or to battery voltage
- Open return (ground) wire at the selective control valve (SCV) I control lever switch, which lets the signal float high
- The selective control valve (SCV) I control lever switch failed internally with a stuck high output
Checks
- 1Unplug the selective control valve (SCV) I control lever switch and, key on, measure the harness signal pin: a value near 5 V points to a harness short or a controller fault rather than the part
- 2Check continuity of the selective control valve (SCV) I control lever switch return wire to the controller sensor ground with both ends disconnected
- 3Operate the SCV lever and watch its switch value change on the service screen.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
John Deere ACU 523923.04Operator controls: SCV i control lever switch low
The controller reads the selective control valve (SCV) I control lever switch signal below its normal range, so it cannot use the value and the function that depends on it runs on a fallback or is switched off. The SCV control lever switch signal is erratic, high or low, so the remote valve may not respond.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Signal wire of the selective control valve (SCV) I control lever switch shorted to ground
- Broken or unplugged 5 V supply wire to the selective control valve (SCV) I control lever switch
- The selective control valve (SCV) I control lever switch failed internally with a stuck low output
Checks
- 1With the selective control valve (SCV) I control lever switch unplugged and the key on, check for the 5 V supply on its harness plug; no supply means a broken feed wire or a faulty controller output
- 2Measure the signal wire to ground with both ends disconnected; a very low resistance means a short to ground in the harness
- 3Operate the SCV lever and watch its switch value change on the service screen.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
John Deere ACU 523960.17Operator not in seat at low speed
The operator presence (seat) sensor reading is below its normal range, so the controller reports a low value; this can be a real condition on the machine and not only a wiring fault. The seat sensor reads no operator, so the tractor may refuse to move at low speed.· Lost messageLost messageCheck soonCauses
- A real low condition on the machine, such as low level, low pressure or a cold engine, behind the operator presence (seat) sensor
- The operator presence (seat) sensor reading low because of a drifting sensor
- Supply or feed problem that holds the value down
Checks
- 1Confirm the real value with an independent gauge or by inspection before blaming the operator presence (seat) sensor
- 2Look for related codes and for a physical cause such as a low level, leak or weak supply
- 3Sit on the seat and watch the seat sensor state; adjust or replace the sensor.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ACU 523960.31Operator not in seat: sensor or absent operator
The controller has set a condition code for the operator presence (seat) sensor: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part. The seat sensor reads no operator, so the tractor may refuse to move at low speed.· OtherOtherCheck soonCauses
- The real condition behind the operator presence (seat) sensor is present
- A related component or circuit that causes the condition
- The message or reminder was not reset after the earlier service
Checks
- 1Confirm on the machine that the condition behind the operator presence (seat) sensor is real and act on it
- 2Read all other codes active at the same time, since this one is often a consequence of another fault
- 3Sit on the seat and watch the seat sensor state; adjust or replace the sensor.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Read which control the code names and check its switch or sensor at the armrest
- 2Read the live switch state on the service screen while operating the control; it should change clean, not flicker
- 3Check the armrest harness and connector for pinched wires and corrosion
- 4Check the ACU supply voltage and ground at its plug with the key on
- 5For message timeouts check the ECU is powered and running before the CAN wiring
Causes
- Switch, lever or sensor failed or erratic
- Wire chafed or broken in the armrest harness
- Low supply voltage at the ACU
- CAN message from the ECU or another controller not arriving
Most common here: lost message (6 of 18)
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
When to stop
You'll notice: The control named in the code does not respond or is cut off, the PTO may not engage, and the tractor may refuse to move when the operator is not detected in the seat.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
